//----------------------------------------------------------------------------- // The FPGA is responsible for interfacing between the A/D, the coil drivers, // and the ARM. In the low-frequency modes it passes the data straight // through, so that the ARM gets raw A/D samples over the SSP. In the high- // frequency modes, the FPGA might perform some demodulation first, to // reduce the amount of data that we must send to the ARM. // // I am not really an FPGA/ASIC designer, so I am sure that a lot of this // could be improved. // // Jonathan Westhues, March 2006 // Added ISO14443-A support by Gerhard de Koning Gans, April 2008 // iZsh , June 2014 //----------------------------------------------------------------------------- `include "hi_read_tx.v" `include "hi_read_rx_xcorr.v" `include "hi_simulate.v" `include "hi_iso14443a.v" `include "hi_sniffer.v" `include "util.v" module fpga_hf( input spck, output miso, input mosi, input ncs, input pck0, input ck_1356meg, input ck_1356megb, output pwr_lo, output pwr_hi, output pwr_oe1, output pwr_oe2, output pwr_oe3, output pwr_oe4, input [7:0] adc_d, output adc_clk, output adc_noe, output ssp_frame, output ssp_din, input ssp_dout, output ssp_clk, input cross_hi, input cross_lo, output dbg ); //----------------------------------------------------------------------------- // The SPI receiver. This sets up the configuration word, which the rest of // the logic looks at to determine how to connect the A/D and the coil // drivers (i.e., which section gets it). Also assign some symbolic names // to the configuration bits, for use below. //----------------------------------------------------------------------------- reg [15:0] shift_reg; reg [7:0] conf_word; // We switch modes between transmitting to the 13.56 MHz tag and receiving // from it, which means that we must make sure that we can do so without // glitching, or else we will glitch the transmitted carrier. always @(posedge ncs) begin case(shift_reg[15:12]) 4'b0001: conf_word <= shift_reg[7:0]; // FPGA_CMD_SET_CONFREG endcase end always @(posedge spck) begin if(~ncs) begin shift_reg[15:1] <= shift_reg[14:0]; shift_reg[0] <= mosi; end end wire [2:0] major_mode; assign major_mode = conf_word[7:5]; // For the high-frequency transmit configuration: modulation depth, either // 100% (just quite driving antenna, steady LOW), or shallower (tri-state // some fraction of the buffers) wire hi_read_tx_shallow_modulation = conf_word[0]; // For the high-frequency receive correlator: frequency against which to // correlate. wire hi_read_rx_xcorr_848 = conf_word[0]; // and whether to drive the coil (reader) or just short it (snooper) wire hi_read_rx_xcorr_snoop = conf_word[1]; // divide subcarrier frequency by 4 wire hi_read_rx_xcorr_quarter = conf_word[2]; // For the high-frequency simulated tag: what kind of modulation to use. wire [2:0] hi_simulate_mod_type = conf_word[2:0]; //----------------------------------------------------------------------------- // And then we instantiate the modules corresponding to each of the FPGA's // major modes, and use muxes to connect the outputs of the active mode to // the output pins. //----------------------------------------------------------------------------- hi_read_tx ht( pck0, ck_1356meg, ck_1356megb, ht_pwr_lo, ht_pwr_hi, ht_pwr_oe1, ht_pwr_oe2, ht_pwr_oe3, ht_pwr_oe4, adc_d, ht_adc_clk, ht_ssp_frame, ht_ssp_din, ssp_dout, ht_ssp_clk, cross_hi, cross_lo, ht_dbg, hi_read_tx_shallow_modulation ); hi_read_rx_xcorr hrxc( pck0, ck_1356meg, ck_1356megb, hrxc_pwr_lo, hrxc_pwr_hi, hrxc_pwr_oe1, hrxc_pwr_oe2, hrxc_pwr_oe3, hrxc_pwr_oe4, adc_d, hrxc_adc_clk, hrxc_ssp_frame, hrxc_ssp_din, ssp_dout, hrxc_ssp_clk, cross_hi, cross_lo, hrxc_dbg, hi_read_rx_xcorr_848, hi_read_rx_xcorr_snoop, hi_read_rx_xcorr_quarter ); hi_simulate hs( pck0, ck_1356meg, ck_1356megb, hs_pwr_lo, hs_pwr_hi, hs_pwr_oe1, hs_pwr_oe2, hs_pwr_oe3, hs_pwr_oe4, adc_d, hs_adc_clk, hs_ssp_frame, hs_ssp_din, ssp_dout, hs_ssp_clk, cross_hi, cross_lo, hs_dbg, hi_simulate_mod_type ); hi_iso14443a hisn( pck0, ck_1356meg, ck_1356megb, hisn_pwr_lo, hisn_pwr_hi, hisn_pwr_oe1, hisn_pwr_oe2, hisn_pwr_oe3, hisn_pwr_oe4, adc_d, hisn_adc_clk, hisn_ssp_frame, hisn_ssp_din, ssp_dout, hisn_ssp_clk, cross_hi, cross_lo, hisn_dbg, hi_simulate_mod_type ); hi_sniffer he( pck0, ck_1356meg, ck_1356megb, he_pwr_lo, he_pwr_hi, he_pwr_oe1, he_pwr_oe2, he_pwr_oe3, he_pwr_oe4, adc_d, he_adc_clk, he_ssp_frame, he_ssp_din, ssp_dout, he_ssp_clk, cross_hi, cross_lo, he_dbg, hi_read_rx_xcorr_848, hi_read_rx_xcorr_snoop, hi_read_rx_xcorr_quarter ); // Major modes: // 000 -- HF reader, transmitting to tag; modulation depth selectable // 001 -- HF reader, receiving from tag, correlating as it goes; frequency selectable // 010 -- HF simulated tag // 011 -- HF ISO14443-A // 100 -- HF Snoop // 111 -- everything off mux8 mux_ssp_clk (major_mode, ssp_clk, ht_ssp_clk, hrxc_ssp_clk, hs_ssp_clk, hisn_ssp_clk, he_ssp_clk, 1'b0, 1'b0, 1'b0); mux8 mux_ssp_din (major_mode, ssp_din, ht_ssp_din, hrxc_ssp_din, hs_ssp_din, hisn_ssp_din, he_ssp_din, 1'b0, 1'b0, 1'b0); mux8 mux_ssp_frame (major_mode, ssp_frame, ht_ssp_frame, hrxc_ssp_frame, hs_ssp_frame, hisn_ssp_frame, he_ssp_frame, 1'b0, 1'b0, 1'b0); mux8 mux_pwr_oe1 (major_mode, pwr_oe1, ht_pwr_oe1, hrxc_pwr_oe1, hs_pwr_oe1, hisn_pwr_oe1, he_pwr_oe1, 1'b0, 1'b0, 1'b0); mux8 mux_pwr_oe2 (major_mode, pwr_oe2, ht_pwr_oe2, hrxc_pwr_oe2, hs_pwr_oe2, hisn_pwr_oe2, he_pwr_oe2, 1'b0, 1'b0, 1'b0); mux8 mux_pwr_oe3 (major_mode, pwr_oe3, ht_pwr_oe3, hrxc_pwr_oe3, hs_pwr_oe3, hisn_pwr_oe3, he_pwr_oe3, 1'b0, 1'b0, 1'b0); mux8 mux_pwr_oe4 (major_mode, pwr_oe4, ht_pwr_oe4, hrxc_pwr_oe4, hs_pwr_oe4, hisn_pwr_oe4, he_pwr_oe4, 1'b0, 1'b0, 1'b0); mux8 mux_pwr_lo (major_mode, pwr_lo, ht_pwr_lo, hrxc_pwr_lo, hs_pwr_lo, hisn_pwr_lo, he_pwr_lo, 1'b0, 1'b0, 1'b0); mux8 mux_pwr_hi (major_mode, pwr_hi, ht_pwr_hi, hrxc_pwr_hi, hs_pwr_hi, hisn_pwr_hi, he_pwr_hi, 1'b0, 1'b0, 1'b0); mux8 mux_adc_clk (major_mode, adc_clk, ht_adc_clk, hrxc_adc_clk, hs_adc_clk, hisn_adc_clk, he_adc_clk, 1'b0, 1'b0, 1'b0); mux8 mux_dbg (major_mode, dbg, ht_dbg, hrxc_dbg, hs_dbg, hisn_dbg, he_dbg, 1'b0, 1'b0, 1'b0); // In all modes, let the ADC's outputs be enabled. assign adc_noe = 1'b0; endmodule