+ LEDsoff();
+ LED(selected + 1, 0);
+ // Finished recording
+
+ // If we were previously playing, set playing off
+ // so next button push begins playing what we recorded
+ playing = 0;
+ }
+
+ // Change where to record (or begin playing)
+ else if (button_pressed)
+ {
+ // Next option if we were previously playing
+ if (playing)
+ selected = (selected + 1) % OPTS;
+ playing = !playing;
+
+ LEDsoff();
+ LED(selected + 1, 0);
+
+ // Begin transmitting
+ if (playing)
+ {
+ LED(LED_GREEN, 0);
+ DbpString("Playing");
+ // wait for button to be released
+ while(BUTTON_PRESS())
+ WDT_HIT();
+ Dbprintf("%x %x %x", selected, high[selected], low[selected]);
+ CmdHIDsimTAG(high[selected], low[selected], 0);
+ DbpString("Done playing");
+ if (BUTTON_HELD(1000) > 0)
+ {
+ DbpString("Exiting");
+ LEDsoff();
+ return;
+ }
+
+ /* We pressed a button so ignore it here with a delay */
+ SpinDelay(300);
+
+ // when done, we're done playing, move to next option
+ selected = (selected + 1) % OPTS;
+ playing = !playing;
+ LEDsoff();
+ LED(selected + 1, 0);
+ }
+ else
+ while(BUTTON_PRESS())
+ WDT_HIT();
+ }
+ }
+}
+#endif
+
+/*
+OBJECTIVE
+Listen and detect an external reader. Determine the best location
+for the antenna.
+
+INSTRUCTIONS:
+Inside the ListenReaderField() function, there is two mode.
+By default, when you call the function, you will enter mode 1.
+If you press the PM3 button one time, you will enter mode 2.
+If you press the PM3 button a second time, you will exit the function.
+
+DESCRIPTION OF MODE 1:
+This mode just listens for an external reader field and lights up green
+for HF and/or red for LF. This is the original mode of the detectreader
+function.
+
+DESCRIPTION OF MODE 2:
+This mode will visually represent, using the LEDs, the actual strength of the
+current compared to the maximum current detected. Basically, once you know
+what kind of external reader is present, it will help you spot the best location to place
+your antenna. You will probably not get some good results if there is a LF and a HF reader
+at the same place! :-)
+
+LIGHT SCHEME USED:
+*/
+static const char LIGHT_SCHEME[] = {
+ 0x0, /* ---- | No field detected */
+ 0x1, /* X--- | 14% of maximum current detected */
+ 0x2, /* -X-- | 29% of maximum current detected */
+ 0x4, /* --X- | 43% of maximum current detected */
+ 0x8, /* ---X | 57% of maximum current detected */
+ 0xC, /* --XX | 71% of maximum current detected */
+ 0xE, /* -XXX | 86% of maximum current detected */
+ 0xF, /* XXXX | 100% of maximum current detected */
+};
+static const int LIGHT_LEN = sizeof(LIGHT_SCHEME)/sizeof(LIGHT_SCHEME[0]);
+
+void ListenReaderField(int limit)
+{
+ int lf_av, lf_av_new, lf_baseline= 0, lf_count= 0, lf_max;
+ int hf_av, hf_av_new, hf_baseline= 0, hf_count= 0, hf_max;
+ int mode=1, display_val, display_max, i;
+
+#define LF_ONLY 1
+#define HF_ONLY 2
+
+ LEDsoff();
+
+ lf_av=lf_max=ReadAdc(ADC_CHAN_LF);
+
+ if(limit != HF_ONLY) {
+ Dbprintf("LF 125/134 Baseline: %d", lf_av);
+ lf_baseline = lf_av;
+ }
+
+ hf_av=hf_max=ReadAdc(ADC_CHAN_HF);
+
+ if (limit != LF_ONLY) {
+ Dbprintf("HF 13.56 Baseline: %d", hf_av);
+ hf_baseline = hf_av;
+ }
+
+ for(;;) {
+ if (BUTTON_PRESS()) {
+ SpinDelay(500);
+ switch (mode) {
+ case 1:
+ mode=2;
+ DbpString("Signal Strength Mode");
+ break;
+ case 2:
+ default:
+ DbpString("Stopped");
+ LEDsoff();
+ return;
+ break;
+ }
+ }
+ WDT_HIT();
+
+ if (limit != HF_ONLY) {
+ if(mode==1) {
+ if (abs(lf_av - lf_baseline) > 10) LED_D_ON();
+ else LED_D_OFF();
+ }
+
+ ++lf_count;
+ lf_av_new= ReadAdc(ADC_CHAN_LF);
+ // see if there's a significant change
+ if(abs(lf_av - lf_av_new) > 10) {
+ Dbprintf("LF 125/134 Field Change: %x %x %x", lf_av, lf_av_new, lf_count);
+ lf_av = lf_av_new;
+ if (lf_av > lf_max)
+ lf_max = lf_av;
+ lf_count= 0;
+ }
+ }
+
+ if (limit != LF_ONLY) {
+ if (mode == 1){
+ if (abs(hf_av - hf_baseline) > 10) LED_B_ON();
+ else LED_B_OFF();
+ }
+
+ ++hf_count;
+ hf_av_new= ReadAdc(ADC_CHAN_HF);
+ // see if there's a significant change
+ if(abs(hf_av - hf_av_new) > 10) {
+ Dbprintf("HF 13.56 Field Change: %x %x %x", hf_av, hf_av_new, hf_count);
+ hf_av = hf_av_new;
+ if (hf_av > hf_max)
+ hf_max = hf_av;
+ hf_count= 0;
+ }
+ }
+
+ if(mode == 2) {
+ if (limit == LF_ONLY) {
+ display_val = lf_av;
+ display_max = lf_max;
+ } else if (limit == HF_ONLY) {
+ display_val = hf_av;
+ display_max = hf_max;
+ } else { /* Pick one at random */
+ if( (hf_max - hf_baseline) > (lf_max - lf_baseline) ) {
+ display_val = hf_av;
+ display_max = hf_max;
+ } else {
+ display_val = lf_av;
+ display_max = lf_max;
+ }
+ }
+ for (i=0; i<LIGHT_LEN; i++) {
+ if (display_val >= ((display_max/LIGHT_LEN)*i) && display_val <= ((display_max/LIGHT_LEN)*(i+1))) {
+ if (LIGHT_SCHEME[i] & 0x1) LED_C_ON(); else LED_C_OFF();
+ if (LIGHT_SCHEME[i] & 0x2) LED_A_ON(); else LED_A_OFF();
+ if (LIGHT_SCHEME[i] & 0x4) LED_B_ON(); else LED_B_OFF();
+ if (LIGHT_SCHEME[i] & 0x8) LED_D_ON(); else LED_D_OFF();
+ break;
+ }
+ }
+ }
+ }
+}
+
+void UsbPacketReceived(uint8_t *packet, int len)
+{
+ UsbCommand *c = (UsbCommand *)packet;
+ UsbCommand ack;
+ ack.cmd = CMD_ACK;
+
+ switch(c->cmd) {
+#ifdef WITH_LF
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_125K:
+ AcquireRawAdcSamples125k(c->arg[0]);
+ UsbSendPacket((uint8_t*)&ack, sizeof(ack));
+ break;
+ case CMD_MOD_THEN_ACQUIRE_RAW_ADC_SAMPLES_125K:
+ ModThenAcquireRawAdcSamples125k(c->arg[0],c->arg[1],c->arg[2],c->d.asBytes);
+ break;
+ case CMD_HID_DEMOD_FSK:
+ CmdHIDdemodFSK(0, 0, 0, 1); // Demodulate HID tag
+ break;
+ case CMD_HID_SIM_TAG:
+ CmdHIDsimTAG(c->arg[0], c->arg[1], 1); // Simulate HID tag by ID
+ break;
+ case CMD_HID_CLONE_TAG:
+ CopyHIDtoT5567(c->arg[0], c->arg[1]); // Clone HID tag by ID to T55x7
+ break;
+ case CMD_EM410X_WRITE_TAG:
+ WriteEM410x(c->arg[0], c->arg[1], c->arg[2]);
+ break;
+ case CMD_READ_TI_TYPE:
+ ReadTItag();
+ break;
+ case CMD_WRITE_TI_TYPE:
+ WriteTItag(c->arg[0],c->arg[1],c->arg[2]);
+ break;
+ case CMD_SIMULATE_TAG_125K:
+ LED_A_ON();
+ SimulateTagLowFrequency(c->arg[0], c->arg[1], 1);
+ LED_A_OFF();
+ break;
+ case CMD_LF_SIMULATE_BIDIR:
+ SimulateTagLowFrequencyBidir(c->arg[0], c->arg[1]);
+ break;
+#endif
+
+#ifdef WITH_ISO15693
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_15693:
+ AcquireRawAdcSamplesIso15693();
+ break;
+ case CMD_RECORD_RAW_ADC_SAMPLES_ISO_15693:
+ RecordRawAdcSamplesIso15693();
+ break;
+
+ case CMD_ISO_15693_COMMAND:
+ DirectTag15693Command(c->arg[0],c->arg[1],c->arg[2],c->d.asBytes);
+ break;
+
+ case CMD_ISO_15693_FIND_AFI:
+ BruteforceIso15693Afi(c->arg[0]);
+ break;
+
+ case CMD_ISO_15693_DEBUG:
+ SetDebugIso15693(c->arg[0]);
+ break;
+
+ case CMD_READER_ISO_15693:
+ ReaderIso15693(c->arg[0]);
+ break;
+ case CMD_SIMTAG_ISO_15693:
+ SimTagIso15693(c->arg[0]);
+ break;
+#endif
+
+#ifdef WITH_LEGICRF
+ case CMD_SIMULATE_TAG_LEGIC_RF:
+ LegicRfSimulate(c->arg[0], c->arg[1], c->arg[2]);
+ break;
+
+ case CMD_WRITER_LEGIC_RF:
+ LegicRfWriter(c->arg[1], c->arg[0]);
+ break;
+
+ case CMD_READER_LEGIC_RF:
+ LegicRfReader(c->arg[0], c->arg[1]);
+ break;
+#endif
+
+#ifdef WITH_ISO14443b
+ case CMD_ACQUIRE_RAW_ADC_SAMPLES_ISO_14443:
+ AcquireRawAdcSamplesIso14443(c->arg[0]);
+ break;
+ case CMD_READ_SRI512_TAG:
+ ReadSRI512Iso14443(c->arg[0]);
+ break;
+ case CMD_READ_SRIX4K_TAG:
+ ReadSRIX4KIso14443(c->arg[0]);
+ break;
+ case CMD_SNOOP_ISO_14443:
+ SnoopIso14443();
+ break;
+ case CMD_SIMULATE_TAG_ISO_14443:
+ SimulateIso14443Tag();
+ break;
+#endif
+
+#ifdef WITH_ISO14443a
+ case CMD_SNOOP_ISO_14443a:
+ SnoopIso14443a();
+ break;
+ case CMD_READER_ISO_14443a:
+ ReaderIso14443a(c, &ack);
+ break;
+ case CMD_SIMULATE_TAG_ISO_14443a:
+ SimulateIso14443aTag(c->arg[0], c->arg[1]); // ## Simulate iso14443a tag - pass tag type & UID
+ break;
+
+ case CMD_READER_MIFARE:
+ ReaderMifare(c->arg[0]);
+ break;
+ case CMD_MIFARE_READBL:
+ MifareReadBlock(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_MIFARE_READSC:
+ MifareReadSector(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_MIFARE_WRITEBL:
+ MifareWriteBlock(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_MIFARE_NESTED:
+ MifareNested(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_MIFARE_CHKKEYS:
+ MifareChkKeys(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_SIMULATE_MIFARE_CARD:
+ Mifare1ksim(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+
+ // emulator
+ case CMD_MIFARE_SET_DBGMODE:
+ MifareSetDbgLvl(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_MIFARE_EML_MEMCLR:
+ MifareEMemClr(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_MIFARE_EML_MEMSET:
+ MifareEMemSet(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_MIFARE_EML_MEMGET:
+ MifareEMemGet(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+ case CMD_MIFARE_EML_CARDLOAD:
+ MifareECardLoad(c->arg[0], c->arg[1], c->arg[2], c->d.asBytes);
+ break;
+#endif
+
+#ifdef WITH_ICLASS
+ // Makes use of ISO14443a FPGA Firmware
+ case CMD_SNOOP_ICLASS:
+ SnoopIClass();
+ break;
+#endif
+
+ case CMD_SIMULATE_TAG_HF_LISTEN:
+ SimulateTagHfListen();
+ break;
+
+ case CMD_BUFF_CLEAR:
+ BufferClear();
+ break;
+
+ case CMD_MEASURE_ANTENNA_TUNING:
+ MeasureAntennaTuning();
+ break;
+
+ case CMD_MEASURE_ANTENNA_TUNING_HF:
+ MeasureAntennaTuningHf();
+ break;
+
+ case CMD_LISTEN_READER_FIELD:
+ ListenReaderField(c->arg[0]);
projects / proxmark3-svn / blobdiff