--- /dev/null
+//-----------------------------------------------------------------------------
+//
+// Jonathan Westhues, April 2006
+//-----------------------------------------------------------------------------
+
+module hi_reader(
+ ck_1356meg,
+ pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
+ adc_d, adc_clk,
+ ssp_frame, ssp_din, ssp_dout, ssp_clk,
+ dbg,
+ subcarrier_frequency, minor_mode
+);
+ input ck_1356meg;
+ output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
+ input [7:0] adc_d;
+ output adc_clk;
+ input ssp_dout;
+ output ssp_frame, ssp_din, ssp_clk;
+ output dbg;
+ input [1:0] subcarrier_frequency;
+ input [2:0] minor_mode;
+
+assign adc_clk = ck_1356meg; // sample frequency is 13,56 MHz
+
+// When we're a reader, we just need to do the BPSK demod; but when we're an
+// eavesdropper, we also need to pick out the commands sent by the reader,
+// using AM. Do this the same way that we do it for the simulated tag.
+reg after_hysteresis, after_hysteresis_prev, after_hysteresis_prev_prev;
+reg [11:0] has_been_low_for;
+always @(negedge adc_clk)
+begin
+ if(& adc_d[7:0]) after_hysteresis <= 1'b1;
+ else if(~(| adc_d[7:0])) after_hysteresis <= 1'b0;
+
+ if(after_hysteresis)
+ begin
+ has_been_low_for <= 7'b0;
+ end
+ else
+ begin
+ if(has_been_low_for == 12'd4095)
+ begin
+ has_been_low_for <= 12'd0;
+ after_hysteresis <= 1'b1;
+ end
+ else
+ has_been_low_for <= has_been_low_for + 1;
+ end
+end
+
+
+// Let us report a correlation every 64 samples. I.e.
+// one Q/I pair after 4 subcarrier cycles for the 848kHz subcarrier,
+// one Q/I pair after 2 subcarrier cycles for the 424kHz subcarriers,
+// one Q/I pair for each subcarrier cyle for the 212kHz subcarrier.
+// We need a 6-bit counter for the timing.
+reg [5:0] corr_i_cnt;
+always @(negedge adc_clk)
+begin
+ corr_i_cnt <= corr_i_cnt + 1;
+end
+
+
+// A couple of registers in which to accumulate the correlations. From the 64 samples
+// we would add at most 32 times the difference between unmodulated and modulated signal. It should
+// be safe to assume that a tag will not be able to modulate the carrier signal by more than 25%.
+// 32 * 255 * 0,25 = 2040, which can be held in 11 bits. Add 1 bit for sign.
+// Temporary we might need more bits. For the 212kHz subcarrier we could possible add 32 times the
+// maximum signal value before a first subtraction would occur. 32 * 255 = 8160 can be held in 13 bits.
+// Add one bit for sign -> need 14 bit registers but final result will fit into 12 bits.
+reg signed [13:0] corr_i_accum;
+reg signed [13:0] corr_q_accum;
+// we will report maximum 8 significant bits
+reg signed [7:0] corr_i_out;
+reg signed [7:0] corr_q_out;
+
+
+// the amplitude of the subcarrier is sqrt(ci^2 + cq^2).
+// approximate by amplitude = max(|ci|,|cq|) + 1/2*min(|ci|,|cq|)
+reg [13:0] corr_amplitude, abs_ci, abs_cq, max_ci_cq;
+reg [12:0] min_ci_cq_2; // min_ci_cq / 2
+
+always @(*)
+begin
+ if (corr_i_accum[13] == 1'b0)
+ abs_ci <= corr_i_accum;
+ else
+ abs_ci <= -corr_i_accum;
+
+ if (corr_q_accum[13] == 1'b0)
+ abs_cq <= corr_q_accum;
+ else
+ abs_cq <= -corr_q_accum;
+
+ if (abs_ci > abs_cq)
+ begin
+ max_ci_cq <= abs_ci;
+ min_ci_cq_2 <= abs_cq / 2;
+ end
+ else
+ begin
+ max_ci_cq <= abs_cq;
+ min_ci_cq_2 <= abs_ci / 2;
+ end
+
+ corr_amplitude <= max_ci_cq + min_ci_cq_2;
+
+end
+
+
+// The subcarrier reference signals
+reg subcarrier_I;
+reg subcarrier_Q;
+
+always @(*)
+begin
+ if (subcarrier_frequency == `FPGA_HF_READER_SUBCARRIER_848_KHZ)
+ begin
+ subcarrier_I = ~corr_i_cnt[3];
+ subcarrier_Q = ~(corr_i_cnt[3] ^ corr_i_cnt[2]);
+ end
+ else if (subcarrier_frequency == `FPGA_HF_READER_SUBCARRIER_212_KHZ)
+ begin
+ subcarrier_I = ~corr_i_cnt[5];
+ subcarrier_Q = ~(corr_i_cnt[5] ^ corr_i_cnt[4]);
+ end
+ else
+ begin // 424 kHz
+ subcarrier_I = ~corr_i_cnt[4];
+ subcarrier_Q = ~(corr_i_cnt[4] ^ corr_i_cnt[3]);
+ end
+end
+
+
+// ADC data appears on the rising edge, so sample it on the falling edge
+always @(negedge adc_clk)
+begin
+ // These are the correlators: we correlate against in-phase and quadrature
+ // versions of our reference signal, and keep the (signed) results or the
+ // resulting amplitude to send out later over the SSP.
+ if(corr_i_cnt == 6'd0)
+ begin
+ if (minor_mode == `FPGA_HF_READER_MODE_SNIFF_AMPLITUDE)
+ begin
+ // send amplitude plus 2 bits reader signal
+ corr_i_out <= corr_amplitude[13:6];
+ corr_q_out <= {corr_amplitude[5:0], after_hysteresis_prev_prev, after_hysteresis_prev};
+ end
+ else if (minor_mode == `FPGA_HF_READER_MODE_SNIFF_IQ)
+ begin
+ // Send 7 most significant bits of in phase tag signal (signed), plus 1 bit reader signal
+ if (corr_i_accum[13:11] == 3'b000 || corr_i_accum[13:11] == 3'b111)
+ corr_i_out <= {corr_i_accum[11:5], after_hysteresis_prev_prev};
+ else // truncate to maximum value
+ if (corr_i_accum[13] == 1'b0)
+ corr_i_out <= {7'b0111111, after_hysteresis_prev_prev};
+ else
+ corr_i_out <= {7'b1000000, after_hysteresis_prev_prev};
+ // Send 7 most significant bits of quadrature phase tag signal (signed), plus 1 bit reader signal
+ if (corr_q_accum[13:11] == 3'b000 || corr_q_accum[13:11] == 3'b111)
+ corr_q_out <= {corr_q_accum[11:5], after_hysteresis_prev};
+ else // truncate to maximum value
+ if (corr_q_accum[13] == 1'b0)
+ corr_q_out <= {7'b0111111, after_hysteresis_prev};
+ else
+ corr_q_out <= {7'b1000000, after_hysteresis_prev};
+ end
+ else if (minor_mode == `FPGA_HF_READER_MODE_RECEIVE_AMPLITUDE)
+ begin
+ // send amplitude
+ corr_i_out <= {2'b00, corr_amplitude[13:8]};
+ corr_q_out <= corr_amplitude[7:0];
+ end
+ else if (minor_mode == `FPGA_HF_READER_MODE_RECEIVE_IQ)
+ begin
+ // Send 8 bits of in phase tag signal
+ if (corr_i_accum[13:11] == 3'b000 || corr_i_accum[13:11] == 3'b111)
+ corr_i_out <= corr_i_accum[11:4];
+ else // truncate to maximum value
+ if (corr_i_accum[13] == 1'b0)
+ corr_i_out <= 8'b01111111;
+ else
+ corr_i_out <= 8'b10000000;
+ // Send 8 bits of quadrature phase tag signal
+ if (corr_q_accum[13:11] == 3'b000 || corr_q_accum[13:11] == 3'b111)
+ corr_q_out <= corr_q_accum[11:4];
+ else // truncate to maximum value
+ if (corr_q_accum[13] == 1'b0)
+ corr_q_out <= 8'b01111111;
+ else
+ corr_q_out <= 8'b10000000;
+ end
+
+ // for each Q/I pair report two reader signal samples when sniffing. Store the 1st.
+ after_hysteresis_prev_prev <= after_hysteresis;
+ // Initialize next correlation.
+ // Both I and Q reference signals are high when corr_i_nct == 0. Therefore need to accumulate.
+ corr_i_accum <= $signed({1'b0,adc_d});
+ corr_q_accum <= $signed({1'b0,adc_d});
+ end
+ else
+ begin
+ if (subcarrier_I)
+ corr_i_accum <= corr_i_accum + $signed({1'b0,adc_d});
+ else
+ corr_i_accum <= corr_i_accum - $signed({1'b0,adc_d});
+
+ if (subcarrier_Q)
+ corr_q_accum <= corr_q_accum + $signed({1'b0,adc_d});
+ else
+ corr_q_accum <= corr_q_accum - $signed({1'b0,adc_d});
+ end
+
+ // for each Q/I pair report two reader signal samples when sniffing. Store the 2nd.
+ if(corr_i_cnt == 6'd32)
+ after_hysteresis_prev <= after_hysteresis;
+
+ // Then the result from last time is serialized and send out to the ARM.
+ // We get one report each cycle, and each report is 16 bits, so the
+ // ssp_clk should be the adc_clk divided by 64/16 = 4.
+ // ssp_clk frequency = 13,56MHz / 4 = 3.39MHz
+
+ if(corr_i_cnt[1:0] == 2'b00)
+ begin
+ // Don't shift if we just loaded new data, obviously.
+ if(corr_i_cnt != 6'd0)
+ begin
+ corr_i_out[7:0] <= {corr_i_out[6:0], corr_q_out[7]};
+ corr_q_out[7:1] <= corr_q_out[6:0];
+ end
+ end
+
+end
+
+
+// ssp clock and frame signal for communication to and from ARM
+reg ssp_clk;
+reg ssp_frame;
+
+always @(negedge adc_clk)
+begin
+ if (corr_i_cnt[1:0] == 2'b00)
+ ssp_clk <= 1'b1;
+ if (corr_i_cnt[1:0] == 2'b10)
+ ssp_clk <= 1'b0;
+
+ // set ssp_frame signal for corr_i_cnt = 1..3
+ // (send one frame with 16 Bits)
+ if (corr_i_cnt == 6'd2)
+ ssp_frame <= 1'b1;
+ if (corr_i_cnt == 6'd14)
+ ssp_frame <= 1'b0;
+end
+
+
+assign ssp_din = corr_i_out[7];
+
+
+// Antenna drivers
+reg pwr_hi, pwr_oe4;
+
+always @(*)
+begin
+ if (minor_mode == `FPGA_HF_READER_MODE_SEND_SHALLOW_MOD)
+ begin
+ pwr_hi = ck_1356meg;
+ pwr_oe4 = ssp_dout;
+ end
+ else if (minor_mode == `FPGA_HF_READER_MODE_SEND_FULL_MOD)
+ begin
+ pwr_hi = ck_1356meg & ~ssp_dout;
+ pwr_oe4 = 1'b0;
+ end
+ else if (minor_mode == `FPGA_HF_READER_MODE_SNIFF_IQ
+ || minor_mode == `FPGA_HF_READER_MODE_SNIFF_AMPLITUDE
+ || minor_mode == `FPGA_HF_READER_MODE_SNIFF_PHASE)
+ begin
+ pwr_hi = 1'b0;
+ pwr_oe4 = 1'b0;
+ end
+ else // receiving from tag
+ begin
+ pwr_hi = ck_1356meg;
+ pwr_oe4 = 1'b0;
+ end
+end
+
+// always on
+assign pwr_oe1 = 1'b0;
+assign pwr_oe3 = 1'b0;
+
+// Unused.
+assign pwr_lo = 1'b0;
+assign pwr_oe2 = 1'b0;
+
+// Debug Output
+assign dbg = corr_i_cnt[3];
+
+endmodule
projects / proxmark3-svn / blobdiff