/*
* LEGIC RF simulation code
- *
+ *
* (c) 2009 Henryk Plötz <henryk@ploetzli.ch>
*/
-#include <proxmark3.h>
+#include "proxmark3.h"
#include "apps.h"
#include "legicrf.h"
-#include "unistd.h"
-#include "stdint.h"
+#include <stdint.h>
+
+#include "legic_prng.h"
+#include "crc.h"
static struct legic_frame {
int bits;
- uint16_t data;
+ uint32_t data;
} current_frame;
+
+static crc_t legic_crc;
+
AT91PS_TC timer;
static void setup_timer(void)
#define FUZZ_EQUAL(value, target, fuzz) ((value) > ((target)-(fuzz)) && (value) < ((target)+(fuzz)))
-static const struct legic_frame queries[] = {
- {7, 0x55}, /* 1010 101 */
-};
-
-static const struct legic_frame responses[] = {
- {6, 0x3b}, /* 1101 11 */
-};
-
-/* Send a frame in tag mode, the FPGA must have been set up by
- * LegicRfSimulate
- */
-static void frame_send_tag(uint16_t response, int bits)
-{
-#if 0
- /* Use the SSC to send a response. 8-bit transfers, LSBit first, 100us per bit */
-#else
- /* Bitbang the response */
- AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
- AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT;
- AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT;
-
- /* Wait for the frame start */
- while(timer->TC_CV < TAG_TIME_WAIT) ;
-
- int i;
- for(i=0; i<bits; i++) {
- int nextbit = timer->TC_CV + TAG_TIME_BIT;
- int bit = response & 1;
- response = response >> 1;
- if(bit)
- AT91C_BASE_PIOA->PIO_SODR = GPIO_SSC_DOUT;
- else
- AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
- while(timer->TC_CV < nextbit) ;
- }
- AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
-#endif
-}
-
/* Send a frame in reader mode, the FPGA must have been set up by
* LegicRfReader
*/
-static void frame_send_rwd(uint16_t data, int bits)
+static void frame_send_rwd(uint32_t data, int bits)
{
/* Start clock */
timer->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
while(timer->TC_CV > 1) ; /* Wait till the clock has reset */
-
+
int i;
for(i=0; i<bits; i++) {
int starttime = timer->TC_CV;
int pause_end = starttime + RWD_TIME_PAUSE, bit_end;
int bit = data & 1;
data = data >> 1;
-
- if(bit) {
+
+ if(bit ^ legic_prng_get_bit()) {
bit_end = starttime + RWD_TIME_1;
} else {
bit_end = starttime + RWD_TIME_0;
}
-
+
/* RWD_TIME_PAUSE time off, then some time on, so that the complete bit time is
* RWD_TIME_x, where x is the bit to be transmitted */
AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
while(timer->TC_CV < pause_end) ;
AT91C_BASE_PIOA->PIO_SODR = GPIO_SSC_DOUT;
+ legic_prng_forward(1); /* bit duration is longest. use this time to forward the lfsr */
+
while(timer->TC_CV < bit_end) ;
}
-
+
{
/* One final pause to mark the end of the frame */
int pause_end = timer->TC_CV + RWD_TIME_PAUSE;
while(timer->TC_CV < pause_end) ;
AT91C_BASE_PIOA->PIO_SODR = GPIO_SSC_DOUT;
}
-
+
/* Reset the timer, to measure time until the start of the tag frame */
timer->TC_CCR = AT91C_TC_SWTRG;
+ while(timer->TC_CV > 1) ; /* Wait till the clock has reset */
}
/* Receive a frame from the card in reader emulation mode, the FPGA and
* timer must have been set up by LegicRfReader and frame_send_rwd.
- *
+ *
* The LEGIC RF protocol from card to reader does not include explicit
* frame start/stop information or length information. The reader must
* know beforehand how many bits it wants to receive. (Notably: a card
* sending a stream of 0-bits is indistinguishable from no card present.)
- *
+ *
* Receive methodology: There is a fancy correlator in hi_read_rx_xcorr, but
* I'm not smart enough to use it. Instead I have patched hi_read_tx to output
* the ADC signal with hysteresis on SSP_DIN. Bit-bang that signal and look
* expected for a 212kHz subcarrier, this was a 1-bit. For timing we use the
* timer that's still running from frame_send_rwd in order to get a synchronization
* with the frame that we just sent.
- *
- * FIXME: Because we're relying on the hysteresis to just do the right thing
+ *
+ * FIXME: Because we're relying on the hysteresis to just do the right thing
* the range is severely reduced (and you'll probably also need a good antenna).
- * So this should be fixed some time in the future for a proper receiver.
+ * So this should be fixed some time in the future for a proper receiver.
*/
-static void frame_receive_rwd(struct legic_frame * const f, int bits)
+static void frame_receive_rwd(struct legic_frame * const f, int bits, int crypt)
{
- uint16_t the_bit = 1; /* Use a bitmask to save on shifts */
- uint16_t data=0;
+ uint32_t the_bit = 1; /* Use a bitmask to save on shifts */
+ uint32_t data=0;
int i, old_level=0, edges=0;
int next_bit_at = TAG_TIME_WAIT;
-
-
+
+
if(bits > 16)
bits = 16;
AT91C_BASE_PIOA->PIO_ODR = GPIO_SSC_DIN;
AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DIN;
+ /* we have some time now, precompute the cipher
+ * since we cannot compute it on the fly while reading */
+ legic_prng_forward(2);
+
+ if(crypt)
+ {
+ for(i=0; i<bits; i++) {
+ data |= legic_prng_get_bit() << i;
+ legic_prng_forward(1);
+ }
+ }
+
while(timer->TC_CV < next_bit_at) ;
+
next_bit_at += TAG_TIME_BIT;
-
+
for(i=0; i<bits; i++) {
edges = 0;
+
while(timer->TC_CV < next_bit_at) {
int level = (AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_DIN);
if(level != old_level)
old_level = level;
}
next_bit_at += TAG_TIME_BIT;
-
+
if(edges > 20 && edges < 60) { /* expected are 42 edges */
- data |= the_bit;
+ data ^= the_bit;
}
-
-
+
the_bit <<= 1;
}
-
+
f->data = data;
f->bits = bits;
-}
-/* Figure out a response to a frame in tag mode */
-static void frame_respond_tag(struct legic_frame const * const f)
-{
- LED_D_ON();
- int i, r_size;
- uint16_t r_data;
-
- for(i=0; i<sizeof(queries)/sizeof(queries[0]); i++) {
- if(f->bits == queries[i].bits && f->data == queries[i].data) {
- r_data = responses[i].data;
- r_size = responses[i].bits;
- break;
- }
- }
-
- if(r_size != 0) {
- frame_send_tag(r_data, r_size);
- LED_A_ON();
- } else {
- LED_A_OFF();
- }
-
- LED_D_OFF();
-}
-
-static void frame_append_bit(struct legic_frame * const f, int bit)
-{
- if(f->bits >= 15)
- return; /* Overflow, won't happen */
- f->data |= (bit<<f->bits);
- f->bits++;
-}
-
-static int frame_is_empty(struct legic_frame const * const f)
-{
- return( f->bits <= 4 );
-}
-
-/* Handle (whether to respond) a frame in tag mode */
-static void frame_handle_tag(struct legic_frame const * const f)
-{
- if(f->bits == 6) {
- /* Short path */
- return;
- }
- if( !frame_is_empty(f) ) {
- frame_respond_tag(f);
- }
+ /* Reset the timer, to synchronize the next frame */
+ timer->TC_CCR = AT91C_TC_SWTRG;
+ while(timer->TC_CV > 1) ; /* Wait till the clock has reset */
}
static void frame_clean(struct legic_frame * const f)
f->bits = 0;
}
-enum emit_mode {
- EMIT_RWD, /* Emit in tag simulation mode, e.g. the source is the RWD */
- EMIT_TAG /* Emit in reader simulation mode, e.g. the source is the TAG */
-};
-static void emit(enum emit_mode mode, int bit)
+static uint32_t perform_setup_phase_rwd(int iv)
{
- if(bit == -1) {
- if(mode == EMIT_RWD) {
- frame_handle_tag(¤t_frame);
- }
- frame_clean(¤t_frame);
- } else if(bit == 0) {
- frame_append_bit(¤t_frame, 0);
- } else if(bit == 1) {
- frame_append_bit(¤t_frame, 1);
- }
-}
-void LegicRfSimulate(void)
-{
- /* ADC path high-frequency peak detector, FPGA in high-frequency simulator mode,
- * modulation mode set to 212kHz subcarrier. We are getting the incoming raw
- * envelope waveform on DIN and should send our response on DOUT.
- *
- * The LEGIC RF protocol is pulse-pause-encoding from reader to card, so we'll
- * measure the time between two rising edges on DIN, and no encoding on the
- * subcarrier from card to reader, so we'll just shift out our verbatim data
- * on DOUT, 1 bit is 100us. The time from reader to card frame is still unclear,
- * seems to be 300us-ish.
- */
- SetAdcMuxFor(GPIO_MUXSEL_HIPKD);
- FpgaSetupSsc();
- FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_SIMULATOR | FPGA_HF_SIMULATOR_MODULATE_212K);
-
- /* Bitbang the receiver */
- AT91C_BASE_PIOA->PIO_ODR = GPIO_SSC_DIN;
- AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DIN;
-
- setup_timer();
-
- int old_level = 0;
- int active = 0;
-
- while(!BUTTON_PRESS()) {
- int level = !!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_DIN);
- int time = timer->TC_CV;
-
- if(level != old_level) {
- if(level == 1) {
- timer->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
- if(FUZZ_EQUAL(time, RWD_TIME_1, RWD_TIME_FUZZ)) {
- /* 1 bit */
- emit(EMIT_RWD, 1);
- active = 1;
- LED_B_ON();
- } else if(FUZZ_EQUAL(time, RWD_TIME_0, RWD_TIME_FUZZ)) {
- /* 0 bit */
- emit(EMIT_RWD, 0);
- active = 1;
- LED_B_ON();
- } else if(active) {
- /* invalid */
- emit(EMIT_RWD, -1);
- active = 0;
- LED_B_OFF();
- }
- }
- }
-
- if(time >= (RWD_TIME_1+RWD_TIME_FUZZ) && active) {
- /* Frame end */
- emit(EMIT_RWD, -1);
- active = 0;
- LED_B_OFF();
- }
-
- if(time >= (20*RWD_TIME_1) && (timer->TC_SR & AT91C_TC_CLKSTA)) {
- timer->TC_CCR = AT91C_TC_CLKDIS;
- }
-
-
- old_level = level;
- WDT_HIT();
- }
+ /* Switch on carrier and let the tag charge for 1ms */
+ AT91C_BASE_PIOA->PIO_SODR = GPIO_SSC_DOUT;
+ SpinDelay(1);
+
+ legic_prng_init(0); /* no keystream yet */
+ frame_send_rwd(iv, 7);
+ legic_prng_init(iv);
+
+ frame_clean(¤t_frame);
+ frame_receive_rwd(¤t_frame, 6, 1);
+ legic_prng_forward(1); /* we wait anyways */
+ while(timer->TC_CV < 387) ; /* ~ 258us */
+ frame_send_rwd(0x19, 6);
+
+ return current_frame.data;
}
-void LegicRfReader(void)
-{
+static void LegicCommonInit(void) {
SetAdcMuxFor(GPIO_MUXSEL_HIPKD);
FpgaSetupSsc();
FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_READER_TX);
-
+
/* Bitbang the transmitter */
AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT;
AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT;
-
+
setup_timer();
-
- while(!BUTTON_PRESS()) {
- /* Switch on carrier and let the tag charge for 1ms */
- AT91C_BASE_PIOA->PIO_SODR = GPIO_SSC_DOUT;
- SpinDelay(1);
-
- LED_A_ON();
- frame_send_rwd(queries[0].data, queries[0].bits);
- LED_A_OFF();
-
- frame_clean(¤t_frame);
- LED_B_ON();
- frame_receive_rwd(¤t_frame, responses[0].bits);
- LED_B_OFF();
-
- /* Switch off carrier, make sure tag is reset */
- AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
- SpinDelay(10);
-
- WDT_HIT();
+
+ crc_init(&legic_crc, 4, 0x19 >> 1, 0x5, 0);
+}
+
+static void switch_off_tag_rwd(void)
+{
+ /* Switch off carrier, make sure tag is reset */
+ AT91C_BASE_PIOA->PIO_CODR = GPIO_SSC_DOUT;
+ SpinDelay(10);
+
+ WDT_HIT();
+}
+/* calculate crc for a legic command */
+static int LegicCRC(int byte_index, int value, int cmd_sz) {
+ crc_clear(&legic_crc);
+ crc_update(&legic_crc, 1, 1); /* CMD_READ */
+ crc_update(&legic_crc, byte_index, cmd_sz-1);
+ crc_update(&legic_crc, value, 8);
+ return crc_finish(&legic_crc);
+}
+
+int legic_read_byte(int byte_index, int cmd_sz) {
+ int byte;
+
+ legic_prng_forward(4); /* we wait anyways */
+ while(timer->TC_CV < 387) ; /* ~ 258us + 100us*delay */
+
+ frame_send_rwd(1 | (byte_index << 1), cmd_sz);
+ frame_clean(¤t_frame);
+
+ frame_receive_rwd(¤t_frame, 12, 1);
+
+ byte = current_frame.data & 0xff;
+ if( LegicCRC(byte_index, byte, cmd_sz) != (current_frame.data >> 8) ) {
+ Dbprintf("!!! crc mismatch: expected %x but got %x !!!", LegicCRC(byte_index, current_frame.data & 0xff, cmd_sz), current_frame.data >> 8);
+ return -1;
}
-
+
+ return byte;
}
+
+/* legic_write_byte() is not included, however it's trivial to implement
+ * and here are some hints on what remains to be done:
+ *
+ * * assemble a write_cmd_frame with crc and send it
+ * * wait until the tag sends back an ACK ('1' bit unencrypted)
+ * * forward the prng based on the timing
+ */
+
+
+void LegicRfReader(int offset, int bytes) {
+ int byte_index=0, cmd_sz=0, card_sz=0;
+
+ LegicCommonInit();
+
+ memset(BigBuf, 0, 1024);
+
+ DbpString("setting up legic card");
+ uint32_t tag_type = perform_setup_phase_rwd(0x55);
+ switch(tag_type) {
+ case 0x1d:
+ DbpString("MIM 256 card found, reading card ...");
+ cmd_sz = 9;
+ card_sz = 256;
+ break;
+ case 0x3d:
+ DbpString("MIM 1024 card found, reading card ...");
+ cmd_sz = 11;
+ card_sz = 1024;
+ break;
+ default:
+ Dbprintf("Unknown card format: %x",tag_type);
+ switch_off_tag_rwd();
+ return;
+ }
+ if(bytes == -1) {
+ bytes = card_sz;
+ }
+ if(bytes+offset >= card_sz) {
+ bytes = card_sz-offset;
+ }
+
+ switch_off_tag_rwd(); //we lost to mutch time with dprintf
+ perform_setup_phase_rwd(0x55);
+
+ while(byte_index < bytes) {
+ int r = legic_read_byte(byte_index+offset, cmd_sz);
+ if(r == -1) {
+ Dbprintf("aborting");
+ switch_off_tag_rwd();
+ return;
+ }
+ ((uint8_t*)BigBuf)[byte_index] = r;
+ byte_index++;
+ }
+ switch_off_tag_rwd();
+ Dbprintf("Card read, use 'hf legic decode' or 'data hexsamples %d' to view results", (bytes+7) & ~7);
+}
+
projects / proxmark3-svn / blobdiff