X-Git-Url: http://git.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/06b58a94f0be3256853a97387fc7e5782ce335c7..1b492a97af74c0cb6c9886bce8b777d6bb50798d:/armsrc/lfops.c diff --git a/armsrc/lfops.c b/armsrc/lfops.c index 0755e1e5..5e01e9b0 100644 --- a/armsrc/lfops.c +++ b/armsrc/lfops.c @@ -17,6 +17,12 @@ #include "crapto1.h" #include "mifareutil.h" +// Sam7s has several timers, we will use the source TIMER_CLOCK1 (aka AT91C_TC_CLKS_TIMER_DIV1_CLOCK) +// TIMER_CLOCK1 = MCK/2, MCK is running at 48 MHz, Timer is running at 48/2 = 24 MHz +// Hitag units (T0) have duration of 8 microseconds (us), which is 1/125000 per second (carrier) +// T0 = TIMER_CLOCK1 / 125000 = 192 +#define T0 192 + #define SHORT_COIL() LOW(GPIO_SSC_DOUT) #define OPEN_COIL() HIGH(GPIO_SSC_DOUT) @@ -57,10 +63,9 @@ void SnoopLFRawAdcSamples(int divisor, int trigger_threshold) // split into two routines so we can avoid timing issues after sending commands // void DoAcquisition125k_internal(int trigger_threshold, bool silent) { - uint8_t *dest = mifare_get_bigbufptr(); - int n = 24000; - int i = 0; - memset(dest, 0x00, n); + uint8_t *dest = get_bigbufptr_recvrespbuf(); + uint16_t i = 0; + memset(dest, 0x00, FREE_BUFFER_SIZE); for(;;) { if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_TXRDY) { @@ -74,7 +79,7 @@ void DoAcquisition125k_internal(int trigger_threshold, bool silent) continue; else trigger_threshold = -1; - if (++i >= n) break; + if (++i >= FREE_BUFFER_SIZE) break; } } if (!silent){ @@ -91,25 +96,20 @@ void DoAcquisition125k() { void ModThenAcquireRawAdcSamples125k(int delay_off, int period_0, int period_1, uint8_t *command) { - - /* Make sure the tag is reset */ FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + + /* Make sure the tag is reset */ FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); SpinDelay(2500); - int divisor_used = 95; // 125 KHz + int divisor = 95; // 125 KHz // see if 'h' was specified - if (command[strlen((char *) command) - 1] == 'h') - divisor_used = 88; // 134.8 KHz + divisor = 88; // 134.8 KHz - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor_used); + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor); FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); // Give it a bit of time for the resonant antenna to settle. - SpinDelay(50); - - - // And a little more time for the tag to fully power up SpinDelay(2000); // Now set up the SSC to get the ADC samples that are now streaming at us. @@ -120,7 +120,7 @@ void ModThenAcquireRawAdcSamples125k(int delay_off, int period_0, int period_1, FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); LED_D_OFF(); SpinDelayUs(delay_off); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor_used); + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor); FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); LED_D_ON(); @@ -132,8 +132,7 @@ void ModThenAcquireRawAdcSamples125k(int delay_off, int period_0, int period_1, FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); LED_D_OFF(); SpinDelayUs(delay_off); - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor_used); - + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, divisor); FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); // now do the read @@ -455,72 +454,162 @@ void WriteTItag(uint32_t idhi, uint32_t idlo, uint16_t crc) // PIO_SODR = Set Output Data Register //#define LOW(x) AT91C_BASE_PIOA->PIO_CODR = (x) //#define HIGH(x) AT91C_BASE_PIOA->PIO_SODR = (x) -void SimulateTagLowFrequency(int period, int gap, int ledcontrol) +void SimulateTagLowFrequency( uint16_t period, uint32_t gap, uint8_t ledcontrol) { - int i = 0; + LED_D_ON(); + + uint16_t i = 0; + uint8_t send = 0; + + //int overflow = 0; + uint8_t *buf = (uint8_t *)BigBuf; + + FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT | FPGA_LF_EDGE_DETECT_READER_FIELD); + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz + SetAdcMuxFor(GPIO_MUXSEL_LOPKD); + RELAY_OFF(); + + // Configure output pin that is connected to the FPGA (for modulating) + AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT; + AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT; + + SHORT_COIL(); + + // Enable Peripheral Clock for TIMER_CLOCK0, used to measure exact timing before answering + AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_TC0); + + // Enable Peripheral Clock for TIMER_CLOCK1, used to capture edges of the reader frames + AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_TC1); + AT91C_BASE_PIOA->PIO_BSR = GPIO_SSC_FRAME; + + // Disable timer during configuration + AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKDIS; + + // Capture mode, default timer source = MCK/2 (TIMER_CLOCK1), TIOA is external trigger, + // external trigger rising edge, load RA on rising edge of TIOA. + AT91C_BASE_TC1->TC_CMR = AT91C_TC_CLKS_TIMER_DIV1_CLOCK | AT91C_TC_ETRGEDG_RISING | AT91C_TC_ABETRG | AT91C_TC_LDRA_RISING; + + // Enable and reset counter + //AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG; + AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG; + + while(!BUTTON_PRESS()) { + WDT_HIT(); + + // Receive frame, watch for at most T0*EOF periods + while (AT91C_BASE_TC1->TC_CV < T0 * 55) { + + // Check if rising edge in modulation is detected + if(AT91C_BASE_TC1->TC_SR & AT91C_TC_LDRAS) { + // Retrieve the new timing values + //int ra = (AT91C_BASE_TC1->TC_RA/T0) + overflow; + //Dbprintf("Timing value - %d %d", ra, overflow); + //overflow = 0; + + // Reset timer every frame, we have to capture the last edge for timing + AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG; + send = 1; + + LED_B_ON(); + } + } + + if ( send ) { + // Disable timer 1 with external trigger to avoid triggers during our own modulation + AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKDIS; + + // Wait for HITAG_T_WAIT_1 carrier periods after the last reader bit, + // not that since the clock counts since the rising edge, but T_Wait1 is + // with respect to the falling edge, we need to wait actually (T_Wait1 - T_Low) + // periods. The gap time T_Low varies (4..10). All timer values are in + // terms of T0 units + while(AT91C_BASE_TC0->TC_CV < T0 * 16 ); + + // datat kommer in som 1 bit för varje position i arrayn + for(i = 0; i < period; ++i) { + + // Reset clock for the next bit + AT91C_BASE_TC0->TC_CCR = AT91C_TC_SWTRG; + + if ( buf[i] > 0 ) + HIGH(GPIO_SSC_DOUT); + else + LOW(GPIO_SSC_DOUT); + + while(AT91C_BASE_TC0->TC_CV < T0 * 1 ); + } + // Drop modulation + LOW(GPIO_SSC_DOUT); + + // Enable and reset external trigger in timer for capturing future frames + AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG; + LED_B_OFF(); + } + + send = 0; + + // Save the timer overflow, will be 0 when frame was received + //overflow += (AT91C_BASE_TC1->TC_CV/T0); + + // Reset the timer to restart while-loop that receives frames + AT91C_BASE_TC1->TC_CCR = AT91C_TC_SWTRG; + } + + LED_B_OFF(); + LED_D_OFF(); + AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKDIS; + AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKDIS; + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + + DbpString("Sim Stopped"); +} + + +void SimulateTagLowFrequencyA(int len, int gap) +{ + //Dbprintf("LEN %d || Gap %d",len, gap); + uint8_t *buf = (uint8_t *)BigBuf; FpgaDownloadAndGo(FPGA_BITSTREAM_LF); FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT); + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT | FPGA_LF_EDGE_DETECT_TOGGLE_MODE); // new izsh toggle mode! // Connect the A/D to the peak-detected low-frequency path. SetAdcMuxFor(GPIO_MUXSEL_LOPKD); // Now set up the SSC to get the ADC samples that are now streaming at us. FpgaSetupSsc(); + SpinDelay(5); - // Configure output and enable pin that is connected to the FPGA (for modulating) - // AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT | GPIO_SSC_CLK; // (PIO_PER) PIO Enable Register - // AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT; // (PIO_OER) Output Enable Register - // AT91C_BASE_PIOA->PIO_ODR = GPIO_SSC_CLK; // (PIO_ODR) Output Disable Register - - AT91C_BASE_PIOA->PIO_OER = GPIO_PCK0; + AT91C_BASE_SSC->SSC_THR = 0x00; + int i = 0; while(!BUTTON_PRESS()) { WDT_HIT(); + if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_TXRDY) { + + if ( buf[i] > 0 ) + AT91C_BASE_SSC->SSC_THR = 0x43; + else + AT91C_BASE_SSC->SSC_THR = 0x00; - // PIO_PDSR = Pin Data Status Register - // GPIO_SSC_CLK = SSC Transmit Clock - // wait ssp_clk == high - while(!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK)) { - if(BUTTON_PRESS()) { - DbpString("Stopped at 0"); - return; - } - WDT_HIT(); - } - - if ( buf[i] > 0 ){ - OPEN_COIL(); - } else { - SHORT_COIL(); - } - - DbpString("Enter Sim3"); - // wait ssp_clk == low - while( (AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK) ) { - if(BUTTON_PRESS()) { - DbpString("stopped at 1"); - return; + ++i; + LED_A_ON(); + if (i >= len){ + i = 0; } - WDT_HIT(); } - DbpString("Enter Sim4 "); - //SpinDelayUs(512); - - ++i; - if(i == period) { - i = 0; - if (gap) { - SHORT_COIL(); - SpinDelay(gap); - } + if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { + volatile uint32_t r = AT91C_BASE_SSC->SSC_RHR; + (void)r; + LED_A_OFF(); } } - DbpString("Stopped"); - return; + DbpString("lf simulate stopped"); + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); } #define DEBUG_FRAME_CONTENTS 1 @@ -529,7 +618,7 @@ void SimulateTagLowFrequencyBidir(int divisor, int t0) } // compose fc/8 fc/10 waveform -static void fc(int c, int *n) { +static void fc(int c, uint16_t *n) { uint8_t *dest = (uint8_t *)BigBuf; int idx; @@ -577,9 +666,9 @@ static void fc(int c, int *n) { // prepare a waveform pattern in the buffer based on the ID given then // simulate a HID tag until the button is pressed -void CmdHIDsimTAG(int hi, int lo, int ledcontrol) +void CmdHIDsimTAG(int hi, int lo, uint8_t ledcontrol) { - int n=0, i=0; + uint16_t n=0, i=0; /* HID tag bitstream format The tag contains a 44bit unique code. This is sent out MSB first in sets of 4 bits @@ -632,14 +721,28 @@ void CmdHIDsimTAG(int hi, int lo, int ledcontrol) LED_A_OFF(); } +//translate wave to 11111100000 (1 for each short wave 0 for each long wave) size_t fsk_demod(uint8_t * dest, size_t size) { uint32_t last_transition = 0; uint32_t idx = 1; - - // we don't care about actual value, only if it's more or less than a - // threshold essentially we capture zero crossings for later analysis - uint8_t threshold_value = 127; + uint32_t maxVal=0; + // // we don't care about actual value, only if it's more or less than a + // // threshold essentially we capture zero crossings for later analysis + + // we do care about the actual value as sometimes near the center of the + // wave we may get static that changes direction of wave for one value + // if our value is too low it might affect the read. and if our tag or + // antenna is weak a setting too high might not see anything. [marshmellow] + if (size<100) return size; + for(idx=1; idx<100; idx++){ + if(maxVal= 2000) return 2000;//something bad happened + return (uint32_t) (f + (float)0.5); +} -size_t aggregate_bits(uint8_t *dest,size_t size, uint8_t h2l_crossing_value,uint8_t l2h_crossing_value, uint8_t maxConsequtiveBits ) +//translate 11111100000 to 10 +size_t aggregate_bits(uint8_t *dest,size_t size, uint8_t rfLen, uint8_t maxConsequtiveBits, uint8_t invert )// uint8_t h2l_crossing_value,uint8_t l2h_crossing_value, { uint8_t lastval=dest[0]; uint32_t idx=0; @@ -680,16 +789,22 @@ size_t aggregate_bits(uint8_t *dest,size_t size, uint8_t h2l_crossing_value,uint continue; } //if lastval was 1, we have a 1->0 crossing - if ( dest[idx-1] ) { - n=(n+1) / h2l_crossing_value; + if ( dest[idx-1]==1 ) { + n=myround((float)(n+1)/((float)(rfLen)/(float)8)); + //n=(n+1) / h2l_crossing_value; } else {// 0->1 crossing - n=(n+1) / l2h_crossing_value; + n=myround((float)(n+1)/((float)(rfLen-2)/(float)10)); + //n=(n+1) / l2h_crossing_value; } if (n == 0) n = 1; if(n < maxConsequtiveBits) { - memset(dest+numBits, dest[idx-1] , n); + if ( invert==0) + memset(dest+numBits, dest[idx-1] , n); + else + memset(dest+numBits, dest[idx-1]^1 , n); + numBits += n; } n=0; @@ -699,13 +814,13 @@ size_t aggregate_bits(uint8_t *dest,size_t size, uint8_t h2l_crossing_value,uint return numBits; } -// loop to capture raw HID waveform then FSK demodulate the TAG ID from it +// loop to get raw HID waveform then FSK demodulate the TAG ID from it void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol) { - uint8_t *dest = (uint8_t *)BigBuf; + uint8_t *dest = get_bigbufptr_recvrespbuf(); size_t size=0,idx=0; //, found=0; - uint32_t hi2=0, hi=0, lo=0; + uint32_t hi2=0, hi=0, lo=0; // Configure to go in 125Khz listen mode LFSetupFPGAForADC(0, true); @@ -716,15 +831,15 @@ void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol) if (ledcontrol) LED_A_ON(); DoAcquisition125k_internal(-1,true); - size = sizeof(BigBuf); // FSK demodulator - size = fsk_demod(dest, size); + size = fsk_demod(dest, FREE_BUFFER_SIZE); // we now have a set of cycle counts, loop over previous results and aggregate data into bit patterns - // 1->0 : fc/8 in sets of 6 - // 0->1 : fc/10 in sets of 5 - size = aggregate_bits(dest,size, 6,5,5); + // 1->0 : fc/8 in sets of 6 (RF/50 / 8 = 6.25) + // 0->1 : fc/10 in sets of 5 (RF/50 / 10= 5) + // do not invert + size = aggregate_bits(dest,size, 50,5,0); //6,5,5,0 WDT_HIT(); @@ -733,8 +848,11 @@ void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol) uint8_t frame_marker_mask[] = {1,1,1,0,0,0}; int numshifts = 0; idx = 0; + //one scan + uint8_t sameCardCount =0; while( idx + sizeof(frame_marker_mask) < size) { // search for a start of frame marker + if (sameCardCount>2) break; //only up to 2 valid sets of data for the same read of looping card data if ( memcmp(dest+idx, frame_marker_mask, sizeof(frame_marker_mask)) == 0) { // frame marker found idx+=sizeof(frame_marker_mask); @@ -743,7 +861,7 @@ void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol) { // Keep going until next frame marker (or error) // Shift in a bit. Start by shifting high registers - hi2=(hi2<<1)|(hi>>31); + hi2=(hi2<<1)|(hi>>31); hi=(hi<<1)|(lo>>31); //Then, shift in a 0 or one into low if (dest[idx] && !dest[idx+1]) // 1 0 @@ -758,25 +876,71 @@ void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol) // Hopefully, we read a tag and hit upon the next frame marker if(idx + sizeof(frame_marker_mask) < size) { - if ( memcmp(dest+idx, frame_marker_mask, sizeof(frame_marker_mask)) == 0) - { - if (hi2 != 0){ - Dbprintf("TAG ID: %x%08x%08x (%d)", - (unsigned int) hi2, (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); + if ( memcmp(dest+idx, frame_marker_mask, sizeof(frame_marker_mask)) == 0) + { + if (hi2 != 0){ //extra large HID tags + Dbprintf("TAG ID: %x%08x%08x (%d)", + (unsigned int) hi2, (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); + } + else { //standard HID tags <38 bits + //Dbprintf("TAG ID: %x%08x (%d)",(unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); //old print cmd + uint8_t bitlen = 0; + uint32_t fc = 0; + uint32_t cardnum = 0; + if (((hi>>5)&1)==1){//if bit 38 is set then < 37 bit format is used + uint32_t lo2=0; + lo2=(((hi & 31) << 12) | (lo>>20)); //get bits 21-37 to check for format len bit + uint8_t idx3 = 1; + while(lo2>1){ //find last bit set to 1 (format len bit) + lo2=lo2>>1; + idx3++; + } + bitlen =idx3+19; + fc =0; + cardnum=0; + if(bitlen==26){ + cardnum = (lo>>1)&0xFFFF; + fc = (lo>>17)&0xFF; + } + if(bitlen==37){ + cardnum = (lo>>1)&0x7FFFF; + fc = ((hi&0xF)<<12)|(lo>>20); + } + if(bitlen==34){ + cardnum = (lo>>1)&0xFFFF; + fc= ((hi&1)<<15)|(lo>>17); + } + if(bitlen==35){ + cardnum = (lo>>1)&0xFFFFF; + fc = ((hi&1)<<11)|(lo>>21); + } + } + else { //if bit 38 is not set then 37 bit format is used + bitlen= 37; + fc =0; + cardnum=0; + if(bitlen==37){ + cardnum = (lo>>1)&0x7FFFF; + fc = ((hi&0xF)<<12)|(lo>>20); + } + } + //Dbprintf("TAG ID: %x%08x (%d)", + // (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); + Dbprintf("TAG ID: %x%08x (%d) - Format Len: %dbit - FC: %d - Card: %d", + (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF, + (unsigned int) bitlen, (unsigned int) fc, (unsigned int) cardnum); + } + sameCardCount++; + if (findone){ + if (ledcontrol) LED_A_OFF(); + return; + } } - else { - Dbprintf("TAG ID: %x%08x (%d)", - (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); - } - } - } - // reset hi2 = hi = lo = 0; numshifts = 0; - }else - { + } else { idx++; } } @@ -802,62 +966,85 @@ uint32_t bytebits_to_byte(uint8_t* src, int numbits) void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol) { uint8_t *dest = (uint8_t *)BigBuf; - size_t size=0, idx=0; uint32_t code=0, code2=0; - + uint8_t isFinish = 0; + // Configure to go in 125Khz listen mode LFSetupFPGAForADC(0, true); - while(!BUTTON_PRESS()) { + while(!BUTTON_PRESS() & !isFinish) { + WDT_HIT(); + if (ledcontrol) LED_A_ON(); DoAcquisition125k_internal(-1,true); size = sizeof(BigBuf); - + //make sure buffer has data + if (size < 64) return; + //test samples are not just noise + uint8_t testMax=0; + for(idx=0;idx<64;idx++){ + if (testMax170){ + //Dbprintf("testMax: %d",testMax); // FSK demodulator size = fsk_demod(dest, size); - // we now have a set of cycle counts, loop over previous results and aggregate data into bit patterns - // 1->0 : fc/8 in sets of 7 - // 0->1 : fc/10 in sets of 6 - size = aggregate_bits(dest, size, 7,6,13); - - WDT_HIT(); - + // 1->0 : fc/8 in sets of 7 (RF/64 / 8 = 8) + // 0->1 : fc/10 in sets of 6 (RF/64 / 10 = 6.4) + size = aggregate_bits(dest, size, 64, 13, 1); //13 max Consecutive should be ok as most 0s in row should be 10 for init seq - invert bits + WDT_HIT(); + //Index map + //0 10 20 30 40 50 60 + //| | | | | | | + //01234567 8 90123456 7 89012345 6 78901234 5 67890123 4 56789012 3 45678901 23 + //----------------------------------------------------------------------------- + //00000000 0 11110000 1 facility 1 version* 1 code*one 1 code*two 1 ???????? 11 + // + //XSF(version)facility:codeone+codetwo //Handle the data + uint8_t sameCardCount=0; uint8_t mask[] = {0,0,0,0,0,0,0,0,0,1}; - for( idx=0; idx < size - 64; idx++) { - - if ( memcmp(dest + idx, mask, sizeof(mask)) ) continue; - - Dbprintf("%d%d%d%d%d%d%d%d",dest[idx], dest[idx+1], dest[idx+2],dest[idx+3],dest[idx+4],dest[idx+5],dest[idx+6],dest[idx+7]); - Dbprintf("%d%d%d%d%d%d%d%d",dest[idx+8], dest[idx+9], dest[idx+10],dest[idx+11],dest[idx+12],dest[idx+13],dest[idx+14],dest[idx+15]); - Dbprintf("%d%d%d%d%d%d%d%d",dest[idx+16],dest[idx+17],dest[idx+18],dest[idx+19],dest[idx+20],dest[idx+21],dest[idx+22],dest[idx+23]); - Dbprintf("%d%d%d%d%d%d%d%d",dest[idx+24],dest[idx+25],dest[idx+26],dest[idx+27],dest[idx+28],dest[idx+29],dest[idx+30],dest[idx+31]); - Dbprintf("%d%d%d%d%d%d%d%d",dest[idx+32],dest[idx+33],dest[idx+34],dest[idx+35],dest[idx+36],dest[idx+37],dest[idx+38],dest[idx+39]); - Dbprintf("%d%d%d%d%d%d%d%d",dest[idx+40],dest[idx+41],dest[idx+42],dest[idx+43],dest[idx+44],dest[idx+45],dest[idx+46],dest[idx+47]); - Dbprintf("%d%d%d%d%d%d%d%d",dest[idx+48],dest[idx+49],dest[idx+50],dest[idx+51],dest[idx+52],dest[idx+53],dest[idx+54],dest[idx+55]); - Dbprintf("%d%d%d%d%d%d%d%d",dest[idx+56],dest[idx+57],dest[idx+58],dest[idx+59],dest[idx+60],dest[idx+61],dest[idx+62],dest[idx+63]); - - code = bytebits_to_byte(dest+idx,32); - code2 = bytebits_to_byte(dest+idx+32,32); + for( idx=0; idx < (size - 74); idx++) { + if (sameCardCount>2) break; + if ( memcmp(dest + idx, mask, sizeof(mask))==0) { + //frame marker found + if (!dest[idx+8] && dest[idx+17]==1 && dest[idx+26]==1 && dest[idx+35]==1 && dest[idx+44]==1 && dest[idx+53]==1){ + //confirmed proper separator bits found + if(findone){ //only print binary if we are doing one + Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx], dest[idx+1], dest[idx+2],dest[idx+3],dest[idx+4],dest[idx+5],dest[idx+6],dest[idx+7],dest[idx+8]); + Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+9], dest[idx+10],dest[idx+11],dest[idx+12],dest[idx+13],dest[idx+14],dest[idx+15],dest[idx+16],dest[idx+17]); + Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+18],dest[idx+19],dest[idx+20],dest[idx+21],dest[idx+22],dest[idx+23],dest[idx+24],dest[idx+25],dest[idx+26]); + Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+27],dest[idx+28],dest[idx+29],dest[idx+30],dest[idx+31],dest[idx+32],dest[idx+33],dest[idx+34],dest[idx+35]); + Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+36],dest[idx+37],dest[idx+38],dest[idx+39],dest[idx+40],dest[idx+41],dest[idx+42],dest[idx+43],dest[idx+44]); + Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+45],dest[idx+46],dest[idx+47],dest[idx+48],dest[idx+49],dest[idx+50],dest[idx+51],dest[idx+52],dest[idx+53]); + Dbprintf("%d%d%d%d%d%d%d%d %d%d",dest[idx+54],dest[idx+55],dest[idx+56],dest[idx+57],dest[idx+58],dest[idx+59],dest[idx+60],dest[idx+61],dest[idx+62],dest[idx+63]); + } + code = bytebits_to_byte(dest+idx,32); + code2 = bytebits_to_byte(dest+idx+32,32); + short version = bytebits_to_byte(dest+idx+27,8); //14,4 + uint8_t facilitycode = bytebits_to_byte(dest+idx+19,8) ; + uint16_t number = (bytebits_to_byte(dest+idx+36,8)<<8)|(bytebits_to_byte(dest+idx+45,8)); //36,9 + + Dbprintf("XSF(%02d)%02x:%d (%08x%08x)",version,facilitycode,number,code,code2); - short version = bytebits_to_byte(dest+idx+14,4); - char unknown = bytebits_to_byte(dest+idx+19,8) ; - uint16_t number = bytebits_to_byte(dest+idx+36,9); - - Dbprintf("XSF(%02d)%02x:%d (%08x%08x)",version,unknown,number,code,code2); - if (ledcontrol) LED_D_OFF(); - - // if we're only looking for one tag - if (findone){ - LED_A_OFF(); - return; + // if we're only looking for one tag + if (findone){ + if (ledcontrol) LED_A_OFF(); + isFinish = 1; + break; + } + sameCardCount++; + } + } + } } - } - WDT_HIT(); + WDT_HIT(); } DbpString("Stopped"); if (ledcontrol) LED_A_OFF(); @@ -994,7 +1181,7 @@ void T55xxWriteBlock(uint32_t Data, uint32_t Block, uint32_t Pwd, uint8_t PwdMod // Read one card block in page 0 void T55xxReadBlock(uint32_t Block, uint32_t Pwd, uint8_t PwdMode) { - uint8_t *dest = mifare_get_bigbufptr(); + uint8_t *dest = get_bigbufptr_recvrespbuf(); uint16_t bufferlength = T55xx_SAMPLES_SIZE; uint32_t i = 0; @@ -1030,13 +1217,14 @@ void T55xxReadBlock(uint32_t Block, uint32_t Pwd, uint8_t PwdMode) for(;;) { if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_TXRDY) { AT91C_BASE_SSC->SSC_THR = 0x43; + //AT91C_BASE_SSC->SSC_THR = 0xff; LED_D_ON(); } if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { dest[i] = (uint8_t)AT91C_BASE_SSC->SSC_RHR; ++i; LED_D_OFF(); - if (i > bufferlength) break; + if (i >= bufferlength) break; } } @@ -1047,9 +1235,9 @@ void T55xxReadBlock(uint32_t Block, uint32_t Pwd, uint8_t PwdMode) // Read card traceability data (page 1) void T55xxReadTrace(void){ - uint8_t *dest = mifare_get_bigbufptr(); + uint8_t *dest = get_bigbufptr_recvrespbuf(); uint16_t bufferlength = T55xx_SAMPLES_SIZE; - int i=0; + uint32_t i = 0; // Clear destination buffer before sending the command 0x80 = average memset(dest, 0x80, bufferlength); @@ -1502,9 +1690,12 @@ int DemodPCF7931(uint8_t **outBlocks) { block_done = 0; half_switch = 0; } + if(i < GraphTraceLen) + { if (GraphBuffer[i-1] > GraphBuffer[i]) dir=0; else dir = 1; } + } if(bitidx==255) bitidx=0; warnings = 0; @@ -1808,7 +1999,7 @@ void EM4xLogin(uint32_t Password) { void EM4xReadWord(uint8_t Address, uint32_t Pwd, uint8_t PwdMode) { - uint8_t *dest = mifare_get_bigbufptr(); + uint8_t *dest = get_bigbufptr_recvrespbuf(); uint16_t bufferlength = 12000; uint32_t i = 0;