X-Git-Url: http://git.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/8e7a6ce40927baad799e6433422d87edef8d489d..9e130475f9d8c727a5d99db54bc6d52b88a13e78:/fpga/lo_passthru.v?ds=sidebyside

diff --git a/fpga/lo_passthru.v b/fpga/lo_passthru.v
index e1cb2ef2..5c59d11c 100644
--- a/fpga/lo_passthru.v
+++ b/fpga/lo_passthru.v
@@ -1,56 +1,56 @@
-//-----------------------------------------------------------------------------
-// For reading TI tags, we need to place the FPGA in pass through mode
-// and pass everything through to the ARM
-//-----------------------------------------------------------------------------
-
-module lo_passthru(
-    pck0, ck_1356meg, ck_1356megb,
-    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
-    adc_d, adc_clk,
-    ssp_frame, ssp_din, ssp_dout, ssp_clk,
-    cross_hi, cross_lo,
-    dbg, divisor
-);
-    input pck0, ck_1356meg, ck_1356megb;
-    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
-    input [7:0] adc_d;
-    output adc_clk;
-    input ssp_dout;
-    output ssp_frame, ssp_din, ssp_clk;
-    input cross_hi, cross_lo;
-    output dbg;
-    input [7:0] divisor;
-
-reg [7:0] pck_divider;
-reg ant_lo;
-
-// this task runs on the rising egde of pck0 clock (24Mhz) and creates ant_lo
-// which is high for (divisor+1) pck0 cycles and low for the same duration
-// ant_lo is therefore a 50% duty cycle clock signal with a frequency of
-// 12Mhz/(divisor+1) which drives the antenna as well as the ADC clock adc_clk
-always @(posedge pck0)
-begin
-	if(pck_divider == divisor[7:0])
-		begin
-			pck_divider <= 8'd0;
-			ant_lo = !ant_lo;
-		end
-	else
-	begin
-		pck_divider <= pck_divider + 1;
-	end
-end
-
-// the antenna is modulated when ssp_dout = 1, when 0 the
-// antenna drivers stop modulating and go into listen mode
-assign pwr_oe3 = 1'b0;
-assign pwr_oe1 = ssp_dout;
-assign pwr_oe2 = ssp_dout;
-assign pwr_oe4 = ssp_dout;
-assign pwr_lo = ant_lo && ssp_dout;
-assign pwr_hi = 1'b0;
-assign adc_clk = 1'b0;
-assign ssp_din = cross_lo;
-assign dbg = cross_lo;
-
-endmodule
+//-----------------------------------------------------------------------------
+// For reading TI tags, we need to place the FPGA in pass through mode
+// and pass everything through to the ARM
+//-----------------------------------------------------------------------------
+
+module lo_passthru(
+    pck0, ck_1356meg, ck_1356megb,
+    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
+    adc_d, adc_clk,
+    ssp_frame, ssp_din, ssp_dout, ssp_clk,
+    cross_hi, cross_lo,
+    dbg, divisor
+);
+    input pck0, ck_1356meg, ck_1356megb;
+    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
+    input [7:0] adc_d;
+    output adc_clk;
+    input ssp_dout;
+    output ssp_frame, ssp_din, ssp_clk;
+    input cross_hi, cross_lo;
+    output dbg;
+    input [7:0] divisor;
+
+reg [7:0] pck_divider;
+reg ant_lo;
+
+// this task runs on the rising egde of pck0 clock (24Mhz) and creates ant_lo
+// which is high for (divisor+1) pck0 cycles and low for the same duration
+// ant_lo is therefore a 50% duty cycle clock signal with a frequency of
+// 12Mhz/(divisor+1) which drives the antenna as well as the ADC clock adc_clk
+always @(posedge pck0)
+begin
+	if(pck_divider == divisor[7:0])
+		begin
+			pck_divider <= 8'd0;
+			ant_lo = !ant_lo;
+		end
+	else
+	begin
+		pck_divider <= pck_divider + 1;
+	end
+end
+
+// the antenna is modulated when ssp_dout = 1, when 0 the
+// antenna drivers stop modulating and go into listen mode
+assign pwr_oe3 = 1'b0;
+assign pwr_oe1 = ssp_dout;
+assign pwr_oe2 = ssp_dout;
+assign pwr_oe4 = ssp_dout;
+assign pwr_lo = ant_lo && ssp_dout;
+assign pwr_hi = 1'b0;
+assign adc_clk = 1'b0;
+assign ssp_din = cross_lo;
+assign dbg = cross_lo;
+
+endmodule