Add command to manually set ADC mux source

[proxmark3-svn] / fpga / hi_simulate.v

//-----------------------------------------------------------------------------\r
// Pretend to be an ISO 14443 tag. We will do this by alternately short-\r
// circuiting and open-circuiting the antenna coil, with the tri-state\r
// pins. \r
//\r
// We communicate over the SSP, as a bitstream (i.e., might as well be\r
// unframed, though we still generate the word sync signal). The output\r
// (ARM -> FPGA) tells us whether to modulate or not. The input (FPGA\r
// -> ARM) is us using the A/D as a fancy comparator; this is with\r
// (software-added) hysteresis, to undo the high-pass filter.\r
//\r
// At this point only Type A is implemented. This means that we are using a\r
// bit rate of 106 kbit/s, or fc/128. Oversample by 4, which ought to make\r
// things practical for the ARM (fc/32, 423.8 kbits/s, ~50 kbytes/s)\r
//\r
// Jonathan Westhues, October 2006\r
//-----------------------------------------------------------------------------\r
\r
module hi_simulate(\r
    pck0, ck_1356meg, ck_1356megb,\r
    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,\r
    adc_d, adc_clk,\r
    ssp_frame, ssp_din, ssp_dout, ssp_clk,\r
    cross_hi, cross_lo,\r
    dbg,\r
    mod_type\r
);\r
    input pck0, ck_1356meg, ck_1356megb;\r
    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;\r
    input [7:0] adc_d;\r
    output adc_clk;\r
    input ssp_dout;\r
    output ssp_frame, ssp_din, ssp_clk;\r
    input cross_hi, cross_lo;\r
    output dbg;\r
    input [2:0] mod_type;\r
\r
// Power amp goes between LOW and tri-state, so pwr_hi (and pwr_lo) can\r
// always be low.\r
assign pwr_hi = 1'b0;\r
assign pwr_lo = 1'b0;\r
\r
// The comparator with hysteresis on the output from the peak detector.\r
reg after_hysteresis;\r
assign adc_clk = ck_1356meg;\r
\r
always @(negedge adc_clk)\r
begin\r
    if(& adc_d[7:5]) after_hysteresis = 1'b1;\r
    else if(~(| adc_d[7:5])) after_hysteresis = 1'b0;\r
end\r
\r
// Divide 13.56 MHz by 32 to produce the SSP_CLK\r
reg [4:0] ssp_clk_divider;\r
always @(posedge adc_clk)\r
    ssp_clk_divider <= (ssp_clk_divider + 1);\r
assign ssp_clk = ssp_clk_divider[4];\r
\r
// Divide SSP_CLK by 8 to produce the byte framing signal; the phase of\r
// this is arbitrary, because it's just a bitstream.\r
// One nasty issue, though: I can't make it work with both rx and tx at\r
// once. The phase wrt ssp_clk must be changed. TODO to find out why\r
// that is and make a better fix.\r
reg [2:0] ssp_frame_divider_to_arm;\r
always @(posedge ssp_clk)\r
    ssp_frame_divider_to_arm <= (ssp_frame_divider_to_arm + 1);\r
reg [2:0] ssp_frame_divider_from_arm;\r
always @(negedge ssp_clk)\r
    ssp_frame_divider_from_arm <= (ssp_frame_divider_from_arm + 1);\r
\r
reg ssp_frame;\r
always @(ssp_frame_divider_to_arm or ssp_frame_divider_from_arm or mod_type)\r
    if(mod_type == 3'b000) // not modulating, so listening, to ARM\r
        ssp_frame = (ssp_frame_divider_to_arm == 3'b000);\r
    else\r
        ssp_frame = (ssp_frame_divider_from_arm == 3'b000);\r
\r
// Synchronize up the after-hysteresis signal, to produce DIN.\r
reg ssp_din;\r
always @(posedge ssp_clk)\r
    ssp_din = after_hysteresis;\r
\r
// Modulating carrier frequency is fc/16, reuse ssp_clk divider for that\r
reg modulating_carrier;\r
always @(mod_type or ssp_clk or ssp_dout)\r
    if(mod_type == 3'b000)\r
        modulating_carrier <= 1'b0;                          // no modulation\r
    else if(mod_type == 3'b001)\r
        modulating_carrier <= ssp_dout ^ ssp_clk_divider[3]; // XOR means BPSK\r
    else\r
        modulating_carrier <= 1'b0;                           // yet unused\r
\r
// This one is all LF, so doesn't matter\r
assign pwr_oe2 = modulating_carrier;\r
\r
// Toggle only one of these, since we are already producing much deeper\r
// modulation than a real tag would.\r
assign pwr_oe1 = modulating_carrier;\r
assign pwr_oe4 = modulating_carrier;\r
\r
// This one is always on, so that we can watch the carrier.\r
assign pwr_oe3 = 1'b0;\r
\r
assign dbg = after_hysteresis;\r
\r
endmodule\r