]>
Commit | Line | Data |
---|---|---|
15c4dc5a | 1 | //----------------------------------------------------------------------------- |
2 | // Routines to load the FPGA image, and then to configure the FPGA's major | |
3 | // mode once it is configured. | |
4 | // | |
5 | // Jonathan Westhues, April 2006 | |
6 | //----------------------------------------------------------------------------- | |
e30c654b | 7 | #include "proxmark3.h" |
15c4dc5a | 8 | #include "apps.h" |
9 | ||
10 | //----------------------------------------------------------------------------- | |
11 | // Set up the Serial Peripheral Interface as master | |
12 | // Used to write the FPGA config word | |
13 | // May also be used to write to other SPI attached devices like an LCD | |
14 | //----------------------------------------------------------------------------- | |
15 | void SetupSpi(int mode) | |
16 | { | |
17 | // PA10 -> SPI_NCS2 chip select (LCD) | |
18 | // PA11 -> SPI_NCS0 chip select (FPGA) | |
19 | // PA12 -> SPI_MISO Master-In Slave-Out | |
20 | // PA13 -> SPI_MOSI Master-Out Slave-In | |
21 | // PA14 -> SPI_SPCK Serial Clock | |
22 | ||
23 | // Disable PIO control of the following pins, allows use by the SPI peripheral | |
24 | AT91C_BASE_PIOA->PIO_PDR = | |
25 | GPIO_NCS0 | | |
26 | GPIO_NCS2 | | |
27 | GPIO_MISO | | |
28 | GPIO_MOSI | | |
29 | GPIO_SPCK; | |
30 | ||
31 | AT91C_BASE_PIOA->PIO_ASR = | |
32 | GPIO_NCS0 | | |
33 | GPIO_MISO | | |
34 | GPIO_MOSI | | |
35 | GPIO_SPCK; | |
36 | ||
37 | AT91C_BASE_PIOA->PIO_BSR = GPIO_NCS2; | |
38 | ||
39 | //enable the SPI Peripheral clock | |
40 | AT91C_BASE_PMC->PMC_PCER = (1<<AT91C_ID_SPI); | |
41 | // Enable SPI | |
42 | AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIEN; | |
43 | ||
44 | switch (mode) { | |
45 | case SPI_FPGA_MODE: | |
46 | AT91C_BASE_SPI->SPI_MR = | |
47 | ( 0 << 24) | // Delay between chip selects (take default: 6 MCK periods) | |
48 | (14 << 16) | // Peripheral Chip Select (selects FPGA SPI_NCS0 or PA11) | |
49 | ( 0 << 7) | // Local Loopback Disabled | |
50 | ( 1 << 4) | // Mode Fault Detection disabled | |
51 | ( 0 << 2) | // Chip selects connected directly to peripheral | |
52 | ( 0 << 1) | // Fixed Peripheral Select | |
53 | ( 1 << 0); // Master Mode | |
54 | AT91C_BASE_SPI->SPI_CSR[0] = | |
55 | ( 1 << 24) | // Delay between Consecutive Transfers (32 MCK periods) | |
56 | ( 1 << 16) | // Delay Before SPCK (1 MCK period) | |
57 | ( 6 << 8) | // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud | |
58 | ( 8 << 4) | // Bits per Transfer (16 bits) | |
59 | ( 0 << 3) | // Chip Select inactive after transfer | |
60 | ( 1 << 1) | // Clock Phase data captured on leading edge, changes on following edge | |
61 | ( 0 << 0); // Clock Polarity inactive state is logic 0 | |
62 | break; | |
63 | case SPI_LCD_MODE: | |
64 | AT91C_BASE_SPI->SPI_MR = | |
65 | ( 0 << 24) | // Delay between chip selects (take default: 6 MCK periods) | |
66 | (11 << 16) | // Peripheral Chip Select (selects LCD SPI_NCS2 or PA10) | |
67 | ( 0 << 7) | // Local Loopback Disabled | |
68 | ( 1 << 4) | // Mode Fault Detection disabled | |
69 | ( 0 << 2) | // Chip selects connected directly to peripheral | |
70 | ( 0 << 1) | // Fixed Peripheral Select | |
71 | ( 1 << 0); // Master Mode | |
72 | AT91C_BASE_SPI->SPI_CSR[2] = | |
73 | ( 1 << 24) | // Delay between Consecutive Transfers (32 MCK periods) | |
74 | ( 1 << 16) | // Delay Before SPCK (1 MCK period) | |
75 | ( 6 << 8) | // Serial Clock Baud Rate (baudrate = MCK/6 = 24Mhz/6 = 4M baud | |
76 | ( 1 << 4) | // Bits per Transfer (9 bits) | |
77 | ( 0 << 3) | // Chip Select inactive after transfer | |
78 | ( 1 << 1) | // Clock Phase data captured on leading edge, changes on following edge | |
79 | ( 0 << 0); // Clock Polarity inactive state is logic 0 | |
80 | break; | |
81 | default: // Disable SPI | |
82 | AT91C_BASE_SPI->SPI_CR = AT91C_SPI_SPIDIS; | |
83 | break; | |
84 | } | |
85 | } | |
86 | ||
87 | //----------------------------------------------------------------------------- | |
88 | // Set up the synchronous serial port, with the one set of options that we | |
89 | // always use when we are talking to the FPGA. Both RX and TX are enabled. | |
90 | //----------------------------------------------------------------------------- | |
91 | void FpgaSetupSsc(void) | |
92 | { | |
93 | // First configure the GPIOs, and get ourselves a clock. | |
94 | AT91C_BASE_PIOA->PIO_ASR = | |
95 | GPIO_SSC_FRAME | | |
96 | GPIO_SSC_DIN | | |
97 | GPIO_SSC_DOUT | | |
98 | GPIO_SSC_CLK; | |
99 | AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DOUT; | |
100 | ||
101 | AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_SSC); | |
102 | ||
103 | // Now set up the SSC proper, starting from a known state. | |
104 | AT91C_BASE_SSC->SSC_CR = AT91C_SSC_SWRST; | |
105 | ||
106 | // RX clock comes from TX clock, RX starts when TX starts, data changes | |
107 | // on RX clock rising edge, sampled on falling edge | |
108 | AT91C_BASE_SSC->SSC_RCMR = SSC_CLOCK_MODE_SELECT(1) | SSC_CLOCK_MODE_START(1); | |
109 | ||
110 | // 8 bits per transfer, no loopback, MSB first, 1 transfer per sync | |
111 | // pulse, no output sync, start on positive-going edge of sync | |
112 | AT91C_BASE_SSC->SSC_RFMR = SSC_FRAME_MODE_BITS_IN_WORD(8) | | |
113 | AT91C_SSC_MSBF | SSC_FRAME_MODE_WORDS_PER_TRANSFER(0); | |
114 | ||
115 | // clock comes from TK pin, no clock output, outputs change on falling | |
116 | // edge of TK, start on rising edge of TF | |
117 | AT91C_BASE_SSC->SSC_TCMR = SSC_CLOCK_MODE_SELECT(2) | | |
118 | SSC_CLOCK_MODE_START(5); | |
119 | ||
120 | // tx framing is the same as the rx framing | |
121 | AT91C_BASE_SSC->SSC_TFMR = AT91C_BASE_SSC->SSC_RFMR; | |
122 | ||
123 | AT91C_BASE_SSC->SSC_CR = AT91C_SSC_RXEN | AT91C_SSC_TXEN; | |
124 | } | |
125 | ||
126 | //----------------------------------------------------------------------------- | |
127 | // Set up DMA to receive samples from the FPGA. We will use the PDC, with | |
128 | // a single buffer as a circular buffer (so that we just chain back to | |
129 | // ourselves, not to another buffer). The stuff to manipulate those buffers | |
130 | // is in apps.h, because it should be inlined, for speed. | |
131 | //----------------------------------------------------------------------------- | |
132 | void FpgaSetupSscDma(BYTE *buf, int len) | |
133 | { | |
134 | AT91C_BASE_PDC_SSC->PDC_RPR = (DWORD)buf; | |
135 | AT91C_BASE_PDC_SSC->PDC_RCR = len; | |
136 | AT91C_BASE_PDC_SSC->PDC_RNPR = (DWORD)buf; | |
137 | AT91C_BASE_PDC_SSC->PDC_RNCR = len; | |
138 | AT91C_BASE_PDC_SSC->PDC_PTCR = AT91C_PDC_RXTEN; | |
139 | } | |
140 | ||
141 | static void DownloadFPGA_byte(unsigned char w) | |
142 | { | |
143 | #define SEND_BIT(x) { if(w & (1<<x) ) HIGH(GPIO_FPGA_DIN); else LOW(GPIO_FPGA_DIN); HIGH(GPIO_FPGA_CCLK); LOW(GPIO_FPGA_CCLK); } | |
144 | SEND_BIT(7); | |
145 | SEND_BIT(6); | |
146 | SEND_BIT(5); | |
147 | SEND_BIT(4); | |
148 | SEND_BIT(3); | |
149 | SEND_BIT(2); | |
150 | SEND_BIT(1); | |
151 | SEND_BIT(0); | |
152 | } | |
153 | ||
154 | // Download the fpga image starting at FpgaImage and with length FpgaImageLen bytes | |
155 | // If bytereversal is set: reverse the byte order in each 4-byte word | |
156 | static void DownloadFPGA(const char *FpgaImage, int FpgaImageLen, int bytereversal) | |
157 | { | |
158 | int i=0; | |
159 | ||
160 | AT91C_BASE_PIOA->PIO_OER = GPIO_FPGA_ON; | |
161 | AT91C_BASE_PIOA->PIO_PER = GPIO_FPGA_ON; | |
162 | HIGH(GPIO_FPGA_ON); // ensure everything is powered on | |
163 | ||
164 | SpinDelay(50); | |
165 | ||
166 | LED_D_ON(); | |
167 | ||
168 | // These pins are inputs | |
169 | AT91C_BASE_PIOA->PIO_ODR = | |
170 | GPIO_FPGA_NINIT | | |
171 | GPIO_FPGA_DONE; | |
172 | // PIO controls the following pins | |
173 | AT91C_BASE_PIOA->PIO_PER = | |
174 | GPIO_FPGA_NINIT | | |
175 | GPIO_FPGA_DONE; | |
176 | // Enable pull-ups | |
177 | AT91C_BASE_PIOA->PIO_PPUER = | |
178 | GPIO_FPGA_NINIT | | |
179 | GPIO_FPGA_DONE; | |
180 | ||
181 | // setup initial logic state | |
182 | HIGH(GPIO_FPGA_NPROGRAM); | |
183 | LOW(GPIO_FPGA_CCLK); | |
184 | LOW(GPIO_FPGA_DIN); | |
185 | // These pins are outputs | |
186 | AT91C_BASE_PIOA->PIO_OER = | |
187 | GPIO_FPGA_NPROGRAM | | |
188 | GPIO_FPGA_CCLK | | |
189 | GPIO_FPGA_DIN; | |
190 | ||
191 | // enter FPGA configuration mode | |
192 | LOW(GPIO_FPGA_NPROGRAM); | |
193 | SpinDelay(50); | |
194 | HIGH(GPIO_FPGA_NPROGRAM); | |
195 | ||
196 | i=100000; | |
197 | // wait for FPGA ready to accept data signal | |
198 | while ((i) && ( !(AT91C_BASE_PIOA->PIO_PDSR & GPIO_FPGA_NINIT ) ) ) { | |
199 | i--; | |
200 | } | |
201 | ||
202 | // crude error indicator, leave both red LEDs on and return | |
203 | if (i==0){ | |
204 | LED_C_ON(); | |
205 | LED_D_ON(); | |
206 | return; | |
207 | } | |
208 | ||
209 | if(bytereversal) { | |
210 | /* This is only supported for DWORD aligned images */ | |
211 | if( ((int)FpgaImage % sizeof(DWORD)) == 0 ) { | |
212 | i=0; | |
213 | while(FpgaImageLen-->0) | |
214 | DownloadFPGA_byte(FpgaImage[(i++)^0x3]); | |
e30c654b | 215 | /* Explanation of the magic in the above line: |
15c4dc5a | 216 | * i^0x3 inverts the lower two bits of the integer i, counting backwards |
217 | * for each 4 byte increment. The generated sequence of (i++)^3 is | |
e30c654b | 218 | * 3 2 1 0 7 6 5 4 11 10 9 8 15 14 13 12 etc. pp. |
15c4dc5a | 219 | */ |
220 | } | |
221 | } else { | |
222 | while(FpgaImageLen-->0) | |
223 | DownloadFPGA_byte(*FpgaImage++); | |
224 | } | |
225 | ||
226 | // continue to clock FPGA until ready signal goes high | |
227 | i=100000; | |
228 | while ( (i--) && ( !(AT91C_BASE_PIOA->PIO_PDSR & GPIO_FPGA_DONE ) ) ) { | |
229 | HIGH(GPIO_FPGA_CCLK); | |
230 | LOW(GPIO_FPGA_CCLK); | |
231 | } | |
232 | // crude error indicator, leave both red LEDs on and return | |
233 | if (i==0){ | |
234 | LED_C_ON(); | |
235 | LED_D_ON(); | |
236 | return; | |
237 | } | |
238 | LED_D_OFF(); | |
239 | } | |
240 | ||
241 | static char *bitparse_headers_start; | |
242 | static char *bitparse_bitstream_end; | |
243 | static int bitparse_initialized; | |
244 | /* Simple Xilinx .bit parser. The file starts with the fixed opaque byte sequence | |
245 | * 00 09 0f f0 0f f0 0f f0 0f f0 00 00 01 | |
246 | * After that the format is 1 byte section type (ASCII character), 2 byte length | |
247 | * (big endian), <length> bytes content. Except for section 'e' which has 4 bytes | |
248 | * length. | |
249 | */ | |
250 | static const char _bitparse_fixed_header[] = {0x00, 0x09, 0x0f, 0xf0, 0x0f, 0xf0, 0x0f, 0xf0, 0x0f, 0xf0, 0x00, 0x00, 0x01}; | |
251 | static int bitparse_init(void * start_address, void *end_address) | |
252 | { | |
253 | bitparse_initialized = 0; | |
e30c654b | 254 | |
15c4dc5a | 255 | if(memcmp(_bitparse_fixed_header, start_address, sizeof(_bitparse_fixed_header)) != 0) { |
256 | return 0; /* Not matched */ | |
257 | } else { | |
258 | bitparse_headers_start= ((char*)start_address) + sizeof(_bitparse_fixed_header); | |
259 | bitparse_bitstream_end= (char*)end_address; | |
260 | bitparse_initialized = 1; | |
261 | return 1; | |
262 | } | |
263 | } | |
264 | ||
265 | int bitparse_find_section(char section_name, char **section_start, unsigned int *section_length) | |
266 | { | |
267 | char *pos = bitparse_headers_start; | |
268 | int result = 0; | |
269 | ||
270 | if(!bitparse_initialized) return 0; | |
271 | ||
272 | while(pos < bitparse_bitstream_end) { | |
273 | char current_name = *pos++; | |
274 | unsigned int current_length = 0; | |
275 | if(current_name < 'a' || current_name > 'e') { | |
276 | /* Strange section name, abort */ | |
277 | break; | |
278 | } | |
279 | current_length = 0; | |
280 | switch(current_name) { | |
281 | case 'e': | |
282 | /* Four byte length field */ | |
283 | current_length += (*pos++) << 24; | |
284 | current_length += (*pos++) << 16; | |
285 | default: /* Fall through, two byte length field */ | |
286 | current_length += (*pos++) << 8; | |
287 | current_length += (*pos++) << 0; | |
288 | } | |
e30c654b | 289 | |
15c4dc5a | 290 | if(current_name != 'e' && current_length > 255) { |
291 | /* Maybe a parse error */ | |
292 | break; | |
293 | } | |
e30c654b | 294 | |
15c4dc5a | 295 | if(current_name == section_name) { |
296 | /* Found it */ | |
297 | *section_start = pos; | |
298 | *section_length = current_length; | |
299 | result = 1; | |
300 | break; | |
301 | } | |
e30c654b | 302 | |
15c4dc5a | 303 | pos += current_length; /* Skip section */ |
304 | } | |
e30c654b | 305 | |
15c4dc5a | 306 | return result; |
307 | } | |
308 | ||
309 | //----------------------------------------------------------------------------- | |
310 | // Find out which FPGA image format is stored in flash, then call DownloadFPGA | |
311 | // with the right parameters to download the image | |
312 | //----------------------------------------------------------------------------- | |
313 | extern char _binary_fpga_bit_start, _binary_fpga_bit_end; | |
314 | void FpgaDownloadAndGo(void) | |
315 | { | |
316 | /* Check for the new flash image format: Should have the .bit file at &_binary_fpga_bit_start | |
317 | */ | |
318 | if(bitparse_init(&_binary_fpga_bit_start, &_binary_fpga_bit_end)) { | |
319 | /* Successfully initialized the .bit parser. Find the 'e' section and | |
320 | * send its contents to the FPGA. | |
321 | */ | |
322 | char *bitstream_start; | |
323 | unsigned int bitstream_length; | |
324 | if(bitparse_find_section('e', &bitstream_start, &bitstream_length)) { | |
325 | DownloadFPGA(bitstream_start, bitstream_length, 0); | |
e30c654b | 326 | |
15c4dc5a | 327 | return; /* All done */ |
328 | } | |
329 | } | |
e30c654b | 330 | |
15c4dc5a | 331 | /* Fallback for the old flash image format: Check for the magic marker 0xFFFFFFFF |
e30c654b | 332 | * 0xAA995566 at address 0x102000. This is raw bitstream with a size of 336,768 bits |
15c4dc5a | 333 | * = 10,524 DWORDs, stored as DWORDS e.g. little-endian in memory, but each DWORD |
334 | * is still to be transmitted in MSBit first order. Set the invert flag to indicate | |
335 | * that the DownloadFPGA function should invert every 4 byte sequence when doing | |
336 | * the bytewise download. | |
337 | */ | |
338 | if( *(DWORD*)0x102000 == 0xFFFFFFFF && *(DWORD*)0x102004 == 0xAA995566 ) | |
339 | DownloadFPGA((char*)0x102000, 10524*4, 1); | |
340 | } | |
341 | ||
342 | void FpgaGatherVersion(char *dst, int len) | |
343 | { | |
e30c654b | 344 | char *fpga_info; |
15c4dc5a | 345 | unsigned int fpga_info_len; |
346 | dst[0] = 0; | |
347 | if(!bitparse_find_section('e', &fpga_info, &fpga_info_len)) { | |
348 | strncat(dst, "FPGA image: legacy image without version information", len-1); | |
349 | } else { | |
350 | strncat(dst, "FPGA image built", len-1); | |
351 | /* USB packets only have 48 bytes data payload, so be terse */ | |
352 | #if 0 | |
353 | if(bitparse_find_section('a', &fpga_info, &fpga_info_len) && fpga_info[fpga_info_len-1] == 0 ) { | |
354 | strncat(dst, " from ", len-1); | |
355 | strncat(dst, fpga_info, len-1); | |
356 | } | |
357 | if(bitparse_find_section('b', &fpga_info, &fpga_info_len) && fpga_info[fpga_info_len-1] == 0 ) { | |
358 | strncat(dst, " for ", len-1); | |
359 | strncat(dst, fpga_info, len-1); | |
360 | } | |
361 | #endif | |
362 | if(bitparse_find_section('c', &fpga_info, &fpga_info_len) && fpga_info[fpga_info_len-1] == 0 ) { | |
363 | strncat(dst, " on ", len-1); | |
364 | strncat(dst, fpga_info, len-1); | |
365 | } | |
366 | if(bitparse_find_section('d', &fpga_info, &fpga_info_len) && fpga_info[fpga_info_len-1] == 0 ) { | |
367 | strncat(dst, " at ", len-1); | |
368 | strncat(dst, fpga_info, len-1); | |
369 | } | |
370 | } | |
371 | } | |
372 | ||
373 | //----------------------------------------------------------------------------- | |
374 | // Send a 16 bit command/data pair to the FPGA. | |
375 | // The bit format is: C3 C2 C1 C0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 | |
376 | // where C is the 4 bit command and D is the 12 bit data | |
377 | //----------------------------------------------------------------------------- | |
378 | void FpgaSendCommand(WORD cmd, WORD v) | |
379 | { | |
380 | SetupSpi(SPI_FPGA_MODE); | |
381 | while ((AT91C_BASE_SPI->SPI_SR & AT91C_SPI_TXEMPTY) == 0); // wait for the transfer to complete | |
382 | AT91C_BASE_SPI->SPI_TDR = AT91C_SPI_LASTXFER | cmd | v; // send the data | |
383 | } | |
384 | //----------------------------------------------------------------------------- | |
385 | // Write the FPGA setup word (that determines what mode the logic is in, read | |
386 | // vs. clone vs. etc.). This is now a special case of FpgaSendCommand() to | |
387 | // avoid changing this function's occurence everywhere in the source code. | |
388 | //----------------------------------------------------------------------------- | |
389 | void FpgaWriteConfWord(BYTE v) | |
390 | { | |
391 | FpgaSendCommand(FPGA_CMD_SET_CONFREG, v); | |
392 | } | |
393 | ||
394 | //----------------------------------------------------------------------------- | |
395 | // Set up the CMOS switches that mux the ADC: four switches, independently | |
396 | // closable, but should only close one at a time. Not an FPGA thing, but | |
397 | // the samples from the ADC always flow through the FPGA. | |
398 | //----------------------------------------------------------------------------- | |
399 | void SetAdcMuxFor(DWORD whichGpio) | |
400 | { | |
401 | AT91C_BASE_PIOA->PIO_OER = | |
402 | GPIO_MUXSEL_HIPKD | | |
403 | GPIO_MUXSEL_LOPKD | | |
404 | GPIO_MUXSEL_LORAW | | |
405 | GPIO_MUXSEL_HIRAW; | |
406 | ||
407 | AT91C_BASE_PIOA->PIO_PER = | |
408 | GPIO_MUXSEL_HIPKD | | |
409 | GPIO_MUXSEL_LOPKD | | |
410 | GPIO_MUXSEL_LORAW | | |
411 | GPIO_MUXSEL_HIRAW; | |
412 | ||
413 | LOW(GPIO_MUXSEL_HIPKD); | |
414 | LOW(GPIO_MUXSEL_HIRAW); | |
415 | LOW(GPIO_MUXSEL_LORAW); | |
416 | LOW(GPIO_MUXSEL_LOPKD); | |
417 | ||
418 | HIGH(whichGpio); | |
419 | } |