-NOTICE:
-(2014-03-17)
-Moving the repository from google code to GitHub is up for discussion!
-Please check out the following thread and post your comments...
-http://www.proxmark.org/forum/viewtopic.php?id=1902
-Discussions will close on March 31st.
-
-INTRO:
-
-This file contains enough software, logic (for the FPGA), and design
-documentation for the hardware that you could, at least in theory,
-do something useful with a proxmark3. It has commands to:
-
- * read any kind of 125 kHz unidirectional tag
- * simulate any kind of 125 kHz unidirectional tag
-
-(This is enough to perform all of the silly cloning attacks, like the
-ones that I did at the Capitol in Sacramento, or anything involving
-a Verichip. From a technical standpoint, these are not that exciting,
-although the `software radio' architecture of the proxmark3 makes it
-easy and fun to support new formats.)
-
-As a bonus, I include some code to use the 13.56 MHz hardware, so you can:
-
- * do anything that a (medium-range) ISO 15693 reader could
- * read an ISO 14443 tag, if you know the higher-layer protocol
- * pretend to be an ISO 14443 tag, if you know the higher-layer protocol
- * snoop on an ISO 14443 transaction
-
-I am not actively developing any of this. I have other projects that
-seem to be more useful.
-
-USING THE PACKAGE:
-
-The software tools required to build include:
-
- * cygwin or other unix-like tools for Windows
- * devkitPro (http://wiki.devkitpro.org/index.php/Getting_Started/devkitARM)
- * Xilinx's WebPack tools
- * Modelsim (for test only)
- * perl
-
-When installing devkitPro, you only need to install the compiler itself. Additional
-support libraries are not required.
-
-Documentation is minimal, but see the doc/ directory for what exists. A
-previous familiarity with the ARM, with digital signal processing,
-and with embedded programming in general is assumed.
-
-The device is used through a specialized command line interface; for
-example, to clone a Verichip, you might type:
-
- loread ; this reads the tag, and stores the
- ; raw samples in memory on the ARM
-
- losamples ; then we download the samples to
- ; the PC
-
- vchdemod clone ; demodulate the ID, and then put it
- ; back in a format that we can replay
-
- losim ; and then replay it
-
-To read an ISO 15693 tag, you might type:
-
- hiread ; read the tag; this involves sending a
- ; particular command, and then getting
- ; the response (which is stored as raw
- ; samples in memory on the ARM)
-
- hisamples ; then download those samples to the PC
-
- hi15demod ; and demod them to bits (and check the
- ; CRC etc. at the same time)
-
-Notice that in both cases the signal processing mostly happened on the PC
-side; that is of course not practical for a real reader, but it is easier
-to initially write your code and debug on the PC side than on the ARM. As
-long as you use integer math (and I do), it's trivial to port it over
-when you're done.
-
-The USB driver and bootloader are documented (and available separately
-for download, if you wish to use them in another project) at
+The iceman fork.
- http://cq.cx/trivia.pl
-
-
-OBTAINING HARDWARE:
-
-Most of the ultra-low-volume contract assemblers that have sprung up
-(Screaming Circuits, the various cheap Asian suppliers, etc.) could put
-something like this together with a reasonable yield. A run of around
-a dozen units is probably cost-effective. The BOM includes (possibly-
-outdated) component pricing, and everything is available from Digikey
-and the usual distributors.
-
-If you've never assembled a modern circuit board by hand, then this is
-not a good place to start. Some of the components (e.g. the crystals)
-must not be assembled with a soldering iron, and require hot air.
-
-The schematics are included; the component values given are not
-necessarily correct for all situations, but it should be possible to do
-nearly anything you would want with appropriate population options.
-
-The printed circuit board artwork is also available, as Gerbers and an
-Excellon drill file.
-
-
-FUTURE PLANS, ENHANCEMENTS THAT YOU COULD MAKE:
-
-At some point I should write software involving a proper real-time
-operating system for the ARM. I would then provide interrupt-driven
-drivers for many of the peripherals that are polled now (the USB,
-the data stream from the FPGA), which would make it easier to develop
-complex applications.
-
-It would not be all that hard to implement the ISO 15693 reader properly
-(with anticollision, all the commands supported, and so on)--the signal
-processing is already written, so it is all straightforward applications
-work.
-
-I have basic support for ISO 14443 as well: a sniffer, a simulated
-tag, and a reader. It won't do anything useful unless you fill in the
-high-layer protocol.
-
-Nicer (i.e., closer-to-optimal) implementations of all kinds of signal
-processing would be useful as well.
-
-A practical implementation of the learning-the-tag's-ID-from-what-the-
-reader-broadcasts-during-anticollision attacks would be relatively
-straightforward. This would involve some signal processing on the FPGA,
-but not much else after that.
-
-It would be neat to write a driver that could stream samples from the A/Ds
-over USB to the PC, using the full available bandwidth of USB. I am not
-yet sure what that would be good for, but surely something. This would
-require a kernel-mode driver under Windows, though, which is more work.
-
-
-LICENSING:
-
-This program is free software; you can redistribute it and/or modify
-it under the terms of the GNU General Public License as published by
-the Free Software Foundation; either version 2 of the License, or
-(at your option) any later version.
-
-This program is distributed in the hope that it will be useful,
-but WITHOUT ANY WARRANTY; without even the implied warranty of
-MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
-GNU General Public License for more details.
-
-You should have received a copy of the GNU General Public License
-along with this program; if not, write to the Free Software
-Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
-
-
-Jonathan Westhues
-user jwesthues, at host cq.cx
-
-May 2007, Cambridge MA
+NOTICE:
+The official Proxmark repository is found here: https://github.com/Proxmark/proxmark3
+
+
+NEWS:
+
+Whats in this fork? I have scraped the web for different enhancements to the PM3 source code and not all of them ever found their way to the master branch.
+Among the stuff is
+
+ * Jonor's hf 14a raw timing patch
+ * Piwi's updates. (usually gets into the master)
+ * Holiman's iclass, (usually gets into the master)
+ * Marshmellow's LF fixes
+ * Midnitesnake's Ultralight, Ultralight-c enhancements
+ * Izsh's lf peak modification / iir-filtering
+ * Aspers's tips and tricks from inside the PM3-gui-tool, settings.xml and other stuff.
+ * My own desfire, Ultralight extras, LF T55xx enhancements, bugs fixes (filelength, hf mf commands ), TNP3xxx lua scripts, Awid26, skidata scripts (will come)
+ * other obscure patches like for the sammy-mode, (offline you know), tagidentifications, defaultkeys.
+
+Give me a hint, and I'll see if I can't merge in the stuff you have.
+
+I don't actually know how to make small pull-request to github :( and that is the number one reason for me not pushing a lot of things back to the PM3 master.
+
+PM3 GUI:
+
+I do tend to rename and move stuff around, the official PM3-GUI from Gaucho will not work so well. *sorry*
+
+
+DEVELOPMENT:
+
+This fork is adjusted to compile on windows/mingw environment with Qt5.3.1 & GCC 4.8
+For people with linux you will need to patch some source code and some small change to one makefile. If you are lazy, you google the forum and find asper's or holimans makefile or you find your solution below.
+
+Common errors linux/macOS finds
+Error:
+ * loclass/fileutils.c:15:2: warning: implicit declaration of function ‘_stat’ [-Wimplicit-function-declaration]
+Solution:
+ * Remove the "unscore" sign. In linux you use without underscore, in windows you need a underscore.
+
+Error:
+ * \client\makefile the parameter -lgdi32
+Solution:
+ * Remove parameter.
+
+Error:
+ * Using older Qt4.6 gives compilation errors.
+Solution
+ * Upgrade to Qt5.3.1
+ OR
+ * Change these two line in \client\makefile
+ CXXFLAGS = -I$(QTDIR)/include -I$(QTDIR)/include/QtCore -I$(QTDIR)/include/QtGui -I$(QTDIR)/include/QtWidgets -I/mingw/include
+ QTLDLIBS = -L$(QTDIR)/lib -lQt5Core -lQt5Gui -lQt5Widgets
+
+ TO
+
+ CXXFLAGS = -I$(QTDIR)/include -I$(QTDIR)/include/QtCore -I$(QTDIR)/include/QtGui
+ QTLDLIBS = -L$(QTDIR)/lib -lQtCore4 -lQtGui4
+
+
+An old Qt4 version makefile is found here: http://www.icesql.se/proxmark3/code/linuxmakefile.txt but this one doesn't have all new files in it. So I don't recommend it.
+
+
+
+January 2015, Sweden
+iceman at host iuse.se
\ No newline at end of file
projects / proxmark3-svn / blobdiff