// Jonathan Westhues, October 2006
//-----------------------------------------------------------------------------
-// possible mod_types:
-`define NO_MODULATION 3'b000
-`define MODULATE_BPSK 3'b001
-`define MODULATE_212K 3'b010
-`define MODULATE_424K 3'b100
-`define MODULATE_424K_8BIT 3'b101
-
module hi_simulate(
- pck0, ck_1356meg, ck_1356megb,
+ ck_1356meg,
pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
adc_d, adc_clk,
ssp_frame, ssp_din, ssp_dout, ssp_clk,
- cross_hi, cross_lo,
dbg,
mod_type
);
- input pck0, ck_1356meg, ck_1356megb;
+ input ck_1356meg;
output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
input [7:0] adc_d;
output adc_clk;
input ssp_dout;
output ssp_frame, ssp_din, ssp_clk;
- input cross_hi, cross_lo;
output dbg;
- input [2:0] mod_type;
+ input [3:0] mod_type;
+assign adc_clk = ck_1356meg;
// The comparator with hysteresis on the output from the peak detector.
reg after_hysteresis;
-assign adc_clk = ck_1356meg;
+reg [11:0] has_been_low_for;
always @(negedge adc_clk)
begin
- if(& adc_d[7:5]) after_hysteresis = 1'b1;
- else if(~(| adc_d[7:5])) after_hysteresis = 1'b0;
+ if (& adc_d[7:5]) after_hysteresis <= 1'b1; // if (adc_d >= 224)
+ else if (~(| adc_d[7:5])) after_hysteresis <= 1'b0; // if (adc_d <= 31)
+
+ if (adc_d >= 224)
+ begin
+ has_been_low_for <= 12'd0;
+ end
+ else
+ begin
+ if (has_been_low_for == 12'd4095)
+ begin
+ has_been_low_for <= 12'd0;
+ after_hysteresis <= 1'b1;
+ end
+ else
+ begin
+ has_been_low_for <= has_been_low_for + 1;
+ end
+ end
end
// Divide 13.56 MHz to produce various frequencies for SSP_CLK
// and modulation.
-reg [7:0] ssp_clk_divider;
+reg [8:0] ssp_clk_divider;
-always @(posedge adc_clk)
+always @(negedge adc_clk)
ssp_clk_divider <= (ssp_clk_divider + 1);
reg ssp_clk;
always @(negedge adc_clk)
begin
- if(mod_type == `MODULATE_424K_8BIT)
+ if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_424K_8BIT)
// Get bit every at 53KHz (every 8th carrier bit of 424kHz)
- ssp_clk <= ssp_clk_divider[7];
- else if(mod_type == `MODULATE_212K)
+ ssp_clk <= ~ssp_clk_divider[7];
+ else if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_212K)
// Get next bit at 212kHz
- ssp_clk <= ssp_clk_divider[5];
+ ssp_clk <= ~ssp_clk_divider[5];
else
// Get next bit at 424Khz
- ssp_clk <= ssp_clk_divider[4];
+ ssp_clk <= ~ssp_clk_divider[4];
end
-// Divide SSP_CLK by 8 to produce the byte framing signal; the phase of
-// this is arbitrary, because it's just a bitstream.
-// One nasty issue, though: I can't make it work with both rx and tx at
-// once. The phase wrt ssp_clk must be changed. TODO to find out why
-// that is and make a better fix.
-reg [2:0] ssp_frame_divider_to_arm;
-always @(posedge ssp_clk)
- ssp_frame_divider_to_arm <= (ssp_frame_divider_to_arm + 1);
-reg [2:0] ssp_frame_divider_from_arm;
-always @(negedge ssp_clk)
- ssp_frame_divider_from_arm <= (ssp_frame_divider_from_arm + 1);
-
-
+// Produce the byte framing signal; the phase of this signal
+// is arbitrary, because it's just a bit stream in this module.
reg ssp_frame;
-always @(ssp_frame_divider_to_arm or ssp_frame_divider_from_arm or mod_type)
- if(mod_type == `NO_MODULATION) // not modulating, so listening, to ARM
- ssp_frame = (ssp_frame_divider_to_arm == 3'b000);
- else
- ssp_frame = (ssp_frame_divider_from_arm == 3'b000);
+always @(negedge adc_clk)
+begin
+ if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_212K)
+ begin
+ if (ssp_clk_divider[8:5] == 4'd1)
+ ssp_frame <= 1'b1;
+ if (ssp_clk_divider[8:5] == 4'd5)
+ ssp_frame <= 1'b0;
+ end
+ else
+ begin
+ if (ssp_clk_divider[7:4] == 4'd1)
+ ssp_frame <= 1'b1;
+ if (ssp_clk_divider[7:4] == 4'd5)
+ ssp_frame <= 1'b0;
+ end
+end
+
// Synchronize up the after-hysteresis signal, to produce DIN.
reg ssp_din;
// Modulating carrier frequency is fc/64 (212kHz) to fc/16 (848kHz). Reuse ssp_clk divider for that.
reg modulating_carrier;
-always @(mod_type or ssp_clk or ssp_dout)
- if (mod_type == `NO_MODULATION)
+always @(*)
+ if (mod_type == `FPGA_HF_SIMULATOR_NO_MODULATION)
modulating_carrier <= 1'b0; // no modulation
- else if (mod_type == `MODULATE_BPSK)
+ else if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_BPSK)
modulating_carrier <= ssp_dout ^ ssp_clk_divider[3]; // XOR means BPSK
- else if (mod_type == `MODULATE_212K)
+ else if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_212K)
modulating_carrier <= ssp_dout & ssp_clk_divider[5]; // switch 212kHz subcarrier on/off
- else if (mod_type == `MODULATE_424K || mod_type == `MODULATE_424K_8BIT)
+ else if (mod_type == `FPGA_HF_SIMULATOR_MODULATE_424K || mod_type == `FPGA_HF_SIMULATOR_MODULATE_424K_8BIT)
modulating_carrier <= ssp_dout & ssp_clk_divider[4]; // switch 424kHz modulation on/off
else
modulating_carrier <= 1'b0; // yet unused
// modulation than a real tag would.
assign pwr_hi = 1'b0; // HF antenna connected to GND
assign pwr_oe3 = 1'b0; // 10k Load
-assign pwr_oe1 = modulating_carrier; // 33 Ohms Load
+assign pwr_oe1 = 1'b0; // 33 Ohms Load
assign pwr_oe4 = modulating_carrier; // 33 Ohms Load
// This is all LF and doesn't matter
assign pwr_oe2 = 1'b0;
-assign dbg = ssp_din;
+assign dbg = ssp_frame;
endmodule
projects / proxmark3-svn / blobdiff