+ strncat(dst, "-suspect", len - strlen(dst) - 1);
+ }
+
+ strncat(dst, " ", len - strlen(dst) - 1);
+ strncat(dst, v->buildtime, len - strlen(dst) - 1);
+ strncat(dst, "\n", len - strlen(dst) - 1);
+}
+
+
+// -------------------------------------------------------------------------
+// timer lib
+// -------------------------------------------------------------------------
+// test procedure:
+//
+// ti = GetTickCount();
+// SpinDelay(1000);
+// ti = GetTickCount() - ti;
+// Dbprintf("timer(1s): %d t=%d", ti, GetTickCount());
+
+void StartTickCount()
+{
+ // This timer is based on the slow clock. The slow clock frequency is between 22kHz and 40kHz.
+ // We can determine the actual slow clock frequency by looking at the Main Clock Frequency Register.
+ uint16_t mainf = AT91C_BASE_PMC->PMC_MCFR & 0xffff; // = 16 * main clock frequency (16MHz) / slow clock frequency
+ // set RealTimeCounter divider to count at 1kHz:
+ AT91C_BASE_RTTC->RTTC_RTMR = AT91C_RTTC_RTTRST | ((256000 + (mainf/2)) / mainf);
+ // note: worst case precision is approx 2.5%
+}
+
+
+/*
+* Get the current count.
+*/
+uint32_t RAMFUNC GetTickCount(){
+ return AT91C_BASE_RTTC->RTTC_RTVR;// was * 2;
+}
+
+
+// -------------------------------------------------------------------------
+// microseconds timer
+// -------------------------------------------------------------------------
+void StartCountUS()
+{
+ AT91C_BASE_PMC->PMC_PCER |= (0x1 << 12) | (0x1 << 13) | (0x1 << 14);
+// AT91C_BASE_TCB->TCB_BMR = AT91C_TCB_TC1XC1S_TIOA0;
+ AT91C_BASE_TCB->TCB_BMR = AT91C_TCB_TC0XC0S_NONE | AT91C_TCB_TC1XC1S_TIOA0 | AT91C_TCB_TC2XC2S_NONE;
+
+ // fast clock
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKDIS; // timer disable
+ AT91C_BASE_TC0->TC_CMR = AT91C_TC_CLKS_TIMER_DIV3_CLOCK | // MCK(48MHz)/32 -- tick=1.5mks
+ AT91C_TC_WAVE | AT91C_TC_WAVESEL_UP_AUTO | AT91C_TC_ACPA_CLEAR |
+ AT91C_TC_ACPC_SET | AT91C_TC_ASWTRG_SET;
+ AT91C_BASE_TC0->TC_RA = 1;
+ AT91C_BASE_TC0->TC_RC = 0xBFFF + 1; // 0xC000
+
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKDIS; // timer disable
+ AT91C_BASE_TC1->TC_CMR = AT91C_TC_CLKS_XC1; // from timer 0
+
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKEN;
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKEN;
+ AT91C_BASE_TCB->TCB_BCR = 1;
+ }
+
+
+uint32_t RAMFUNC GetCountUS(){
+ return (AT91C_BASE_TC1->TC_CV * 0x8000) + ((AT91C_BASE_TC0->TC_CV * 2) / 3); //was /15) * 10);
+}
+
+
+static uint32_t GlobalUsCounter = 0;
+
+uint32_t RAMFUNC GetDeltaCountUS(){
+ uint32_t g_cnt = GetCountUS();
+ uint32_t g_res = g_cnt - GlobalUsCounter;
+ GlobalUsCounter = g_cnt;
+ return g_res;
+}
+
+
+// -------------------------------------------------------------------------
+// Timer for iso14443 commands. Uses ssp_clk from FPGA
+// -------------------------------------------------------------------------
+void StartCountSspClk()
+{
+ AT91C_BASE_PMC->PMC_PCER = (1 << AT91C_ID_TC0) | (1 << AT91C_ID_TC1) | (1 << AT91C_ID_TC2); // Enable Clock to all timers
+ AT91C_BASE_TCB->TCB_BMR = AT91C_TCB_TC0XC0S_TIOA1 // XC0 Clock = TIOA1
+ | AT91C_TCB_TC1XC1S_NONE // XC1 Clock = none
+ | AT91C_TCB_TC2XC2S_TIOA0; // XC2 Clock = TIOA0
+
+ // configure TC1 to create a short pulse on TIOA1 when a rising edge on TIOB1 (= ssp_clk from FPGA) occurs:
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKDIS; // disable TC1
+ AT91C_BASE_TC1->TC_CMR = AT91C_TC_CLKS_TIMER_DIV1_CLOCK // TC1 Clock = MCK(48MHz)/2 = 24MHz
+ | AT91C_TC_CPCSTOP // Stop clock on RC compare
+ | AT91C_TC_EEVTEDG_RISING // Trigger on rising edge of Event
+ | AT91C_TC_EEVT_TIOB // Event-Source: TIOB1 (= ssp_clk from FPGA = 13,56MHz/16)
+ | AT91C_TC_ENETRG // Enable external trigger event
+ | AT91C_TC_WAVESEL_UP // Upmode without automatic trigger on RC compare
+ | AT91C_TC_WAVE // Waveform Mode
+ | AT91C_TC_AEEVT_SET // Set TIOA1 on external event
+ | AT91C_TC_ACPC_CLEAR; // Clear TIOA1 on RC Compare
+ AT91C_BASE_TC1->TC_RC = 0x04; // RC Compare value = 0x04
+
+ // use TC0 to count TIOA1 pulses
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKDIS; // disable TC0
+ AT91C_BASE_TC0->TC_CMR = AT91C_TC_CLKS_XC0 // TC0 clock = XC0 clock = TIOA1
+ | AT91C_TC_WAVE // Waveform Mode
+ | AT91C_TC_WAVESEL_UP // just count
+ | AT91C_TC_ACPA_CLEAR // Clear TIOA0 on RA Compare
+ | AT91C_TC_ACPC_SET; // Set TIOA0 on RC Compare
+ AT91C_BASE_TC0->TC_RA = 1; // RA Compare value = 1; pulse width to TC2
+ AT91C_BASE_TC0->TC_RC = 0; // RC Compare value = 0; increment TC2 on overflow
+
+ // use TC2 to count TIOA0 pulses (giving us a 32bit counter (TC0/TC2) clocked by ssp_clk)
+ AT91C_BASE_TC2->TC_CCR = AT91C_TC_CLKDIS; // disable TC2
+ AT91C_BASE_TC2->TC_CMR = AT91C_TC_CLKS_XC2 // TC2 clock = XC2 clock = TIOA0
+ | AT91C_TC_WAVE // Waveform Mode
+ | AT91C_TC_WAVESEL_UP; // just count
+
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKEN; // enable TC0
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKEN; // enable TC1
+ AT91C_BASE_TC2->TC_CCR = AT91C_TC_CLKEN; // enable TC2
+
+ //
+ // synchronize the counter with the ssp_frame signal. Note: FPGA must be in any iso14443 mode, otherwise SSC_FRAME and SSC_CLK signals would not be present
+ //
+ while(!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_FRAME)); // wait for ssp_frame to go high (start of frame)
+ while(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_FRAME); // wait for ssp_frame to be low
+ while(!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK)); // wait for ssp_clk to go high
+ // note: up to now two ssp_clk rising edges have passed since the rising edge of ssp_frame
+ // it is now safe to assert a sync signal. This sets all timers to 0 on next active clock edge
+ AT91C_BASE_TCB->TCB_BCR = 1; // assert Sync (set all timers to 0 on next active clock edge)
+ // at the next (3rd) ssp_clk rising edge, TC1 will be reset (and not generate a clock signal to TC0)
+ // at the next (4th) ssp_clk rising edge, TC0 (the low word of our counter) will be reset. From now on,
+ // whenever the last three bits of our counter go 0, we can be sure to be in the middle of a frame transfer.
+ // (just started with the transfer of the 4th Bit).
+ // The high word of the counter (TC2) will not reset until the low word (TC0) overflows. Therefore need to wait quite some time before
+ // we can use the counter.
+ while (AT91C_BASE_TC0->TC_CV < 0xFFFF);
+ // Note: needs one more SSP_CLK cycle (1.18 us) until TC2 resets. Don't call GetCountSspClk() that soon.
+}
+
+
+void ResetSspClk(void) {
+ //enable clock of timer and software trigger
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ AT91C_BASE_TC2->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ while (AT91C_BASE_TC2->TC_CV > 0);
+}
+
+
+uint32_t RAMFUNC GetCountSspClk(){
+ uint32_t tmp_count;
+ tmp_count = (AT91C_BASE_TC2->TC_CV << 16) | AT91C_BASE_TC0->TC_CV;
+ if ((tmp_count & 0x0000ffff) == 0) { //small chance that we may have missed an increment in TC2
+ return (AT91C_BASE_TC2->TC_CV << 16);
+ }
+ else {
+ return tmp_count;
+ }
+}
+
+
+// -------------------------------------------------------------------------
+// Timer for bitbanging, or LF stuff when you need a very precis timer
+// 1us = 1.5ticks
+// -------------------------------------------------------------------------
+void StartTicks(void){
+ //initialization of the timer
+ // tc1 is higher 0xFFFF0000
+ // tc0 is lower 0x0000FFFF
+ AT91C_BASE_PMC->PMC_PCER |= (1 << AT91C_ID_TC0) | (1 << AT91C_ID_TC1);
+ AT91C_BASE_TCB->TCB_BMR = AT91C_TCB_TC0XC0S_NONE | AT91C_TCB_TC1XC1S_TIOA0 | AT91C_TCB_TC2XC2S_NONE;
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKDIS;
+ AT91C_BASE_TC0->TC_CMR = AT91C_TC_CLKS_TIMER_DIV3_CLOCK | // MCK(48MHz) / 32
+ AT91C_TC_WAVE | AT91C_TC_WAVESEL_UP_AUTO | AT91C_TC_ACPA_CLEAR |
+ AT91C_TC_ACPC_SET | AT91C_TC_ASWTRG_SET;
+ AT91C_BASE_TC0->TC_RA = 1;
+ AT91C_BASE_TC0->TC_RC = 0;
+
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKDIS; // timer disable
+ AT91C_BASE_TC1->TC_CMR = AT91C_TC_CLKS_XC1; // from TC0
+
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ AT91C_BASE_TCB->TCB_BCR = 1;
+
+ // wait until timer becomes zero.
+ while (AT91C_BASE_TC1->TC_CV > 0);
+}
+
+
+// Wait - Spindelay in ticks.
+// if called with a high number, this will trigger the WDT...
+void WaitTicks(uint32_t ticks){
+ if ( ticks == 0 ) return;
+ ticks += GET_TICKS;
+ while (GET_TICKS < ticks);
+}
+
+
+// Wait / Spindelay in us (microseconds)
+// 1us = 1.5ticks.
+void WaitUS(uint16_t us){
+ if ( us == 0 ) return;
+ WaitTicks( (uint32_t)(us * 1.5) );
+}
+
+
+void WaitMS(uint16_t ms){
+ if (ms == 0) return;
+ WaitTicks( (uint32_t)(ms * 1500) );
+}
+
+
+// Starts Clock and waits until its reset
+void ResetTicks(void){
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ while (AT91C_BASE_TC1->TC_CV > 0);
+}
+
+
+void ResetTimer(AT91PS_TC timer){
+ timer->TC_CCR = AT91C_TC_CLKEN | AT91C_TC_SWTRG;
+ while(timer->TC_CV > 0) ;
+}
+
+
+// stop clock
+void StopTicks(void){
+ AT91C_BASE_TC0->TC_CCR = AT91C_TC_CLKDIS;
+ AT91C_BASE_TC1->TC_CCR = AT91C_TC_CLKDIS;
+}
+
+
+static uint64_t next_random = 1;
+
+/* Generates a (non-cryptographically secure) 32-bit random number.
+ *
+ * We don't have an implementation of the "rand" function or a clock to seed it
+ * with, so we just call GetTickCount the first time to seed ourselves.
+ */
+uint32_t prand() {
+ if (next_random == 1) {
+ next_random = GetTickCount();
projects / proxmark3-svn / blobdiff