X-Git-Url: https://git.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/0422e2a47109a7845998c2130ae40c6d04e56d09..a0a61c91ccefed75187e810cca0e3bcb319ecdcf:/armsrc/lfops.c diff --git a/armsrc/lfops.c b/armsrc/lfops.c index 6ac4e725..90b8d0b3 100644 --- a/armsrc/lfops.c +++ b/armsrc/lfops.c @@ -1,644 +1,1747 @@ -//----------------------------------------------------------------------------- -// Miscellaneous routines for low frequency tag operations. -// Tags supported here so far are Texas Instruments (TI), HID -// Also routines for raw mode reading/simulating of LF waveform -// -//----------------------------------------------------------------------------- -#include -#include "apps.h" -#include "../common/crc16.c" - -void AcquireRawAdcSamples125k(BOOL at134khz) -{ - if(at134khz) { - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - } else { - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - } - - // Connect the A/D to the peak-detected low-frequency path. - SetAdcMuxFor(GPIO_MUXSEL_LOPKD); - - // Give it a bit of time for the resonant antenna to settle. - SpinDelay(50); - - // Now set up the SSC to get the ADC samples that are now streaming at us. - FpgaSetupSsc(); - - // Now call the acquisition routine - DoAcquisition125k(at134khz); -} - -// split into two routines so we can avoid timing issues after sending commands // -void DoAcquisition125k(BOOL at134khz) -{ - BYTE *dest = (BYTE *)BigBuf; - int n = sizeof(BigBuf); - int i; - - memset(dest,0,n); - i = 0; - for(;;) { - if(SSC_STATUS & (SSC_STATUS_TX_READY)) { - SSC_TRANSMIT_HOLDING = 0x43; - LED_D_ON(); - } - if(SSC_STATUS & (SSC_STATUS_RX_READY)) { - dest[i] = (BYTE)SSC_RECEIVE_HOLDING; - i++; - LED_D_OFF(); - if(i >= n) { - break; - } - } - } - DbpIntegers(dest[0], dest[1], at134khz); -} - -void ModThenAcquireRawAdcSamples125k(int delay_off,int period_0,int period_1,BYTE *command) -{ - BOOL at134khz; - - // see if 'h' was specified - if(command[strlen((char *) command) - 1] == 'h') - at134khz= TRUE; - else - at134khz= FALSE; - - if(at134khz) { - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - } else { - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - } - - // Give it a bit of time for the resonant antenna to settle. - SpinDelay(50); - - // Now set up the SSC to get the ADC samples that are now streaming at us. - FpgaSetupSsc(); - - // now modulate the reader field - while(*command != '\0' && *command != ' ') - { - FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); - LED_D_OFF(); - SpinDelayUs(delay_off); - if(at134khz) { - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - } else { - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - } - LED_D_ON(); - if(*(command++) == '0') - SpinDelayUs(period_0); - else - SpinDelayUs(period_1); - } - FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); - LED_D_OFF(); - SpinDelayUs(delay_off); - if(at134khz) { - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - } else { - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - } - - // now do the read - DoAcquisition125k(at134khz); -} - -void AcquireTiType(void) -{ - int i; - // tag transmission is <20ms, sampling at 2M gives us 40K samples max - // each sample is 1 bit stuffed into a DWORD so we need 1250 DWORDS - int n = 1250; - - // clear buffer - DbpIntegers((DWORD)BigBuf, sizeof(BigBuf), 0x12345678); - memset(BigBuf,0,sizeof(BigBuf)); - - // Set up the synchronous serial port - PIO_DISABLE = (1<= n) return; - } - WDT_HIT(); - } - - // return stolen pin to SSP - PIO_DISABLE = (1<>8)&0xff); - crc = update_crc16(crc, (idlo>>16)&0xff); - crc = update_crc16(crc, (idlo>>24)&0xff); - crc = update_crc16(crc, (idhi)&0xff); - crc = update_crc16(crc, (idhi>>8)&0xff); - crc = update_crc16(crc, (idhi>>16)&0xff); - crc = update_crc16(crc, (idhi>>24)&0xff); - } - DbpString("Writing the following data to tag:"); - DbpIntegers(idhi, idlo, crc); - - // TI tags charge at 134.2Khz - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz - // Place FPGA in passthrough mode, in this mode the CROSS_LO line - // connects to SSP_DIN and the SSP_DOUT logic level controls - // whether we're modulating the antenna (high) - // or listening to the antenna (low) - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_PASSTHRU); - LED_A_ON(); - - // steal this pin from the SSP and use it to control the modulation - PIO_ENABLE = (1<>8 )&0xff ); - WriteTIbyte( (idlo>>16)&0xff ); - WriteTIbyte( (idlo>>24)&0xff ); - WriteTIbyte( (idhi )&0xff ); - WriteTIbyte( (idhi>>8 )&0xff ); - WriteTIbyte( (idhi>>16)&0xff ); - WriteTIbyte( (idhi>>24)&0xff ); // data hi to lo - WriteTIbyte( (crc )&0xff ); // crc lo - WriteTIbyte( (crc>>8 )&0xff ); // crc hi - WriteTIbyte(0x00); // write frame lo - WriteTIbyte(0x03); // write frame hi - PIO_OUTPUT_DATA_SET = (1<0xFFF) { - DbpString("Tags can only have 44 bits."); - return; - } - fc(0,&n); - // special start of frame marker containing invalid bit sequences - fc(8, &n); fc(8, &n); // invalid - fc(8, &n); fc(10, &n); // logical 0 - fc(10, &n); fc(10, &n); // invalid - fc(8, &n); fc(10, &n); // logical 0 - - WDT_HIT(); - // manchester encode bits 43 to 32 - for (i=11; i>=0; i--) { - if ((i%4)==3) fc(0,&n); - if ((hi>>i)&1) { - fc(10, &n); fc(8, &n); // low-high transition - } else { - fc(8, &n); fc(10, &n); // high-low transition - } - } - - WDT_HIT(); - // manchester encode bits 31 to 0 - for (i=31; i>=0; i--) { - if ((i%4)==3) fc(0,&n); - if ((lo>>i)&1) { - fc(10, &n); fc(8, &n); // low-high transition - } else { - fc(8, &n); fc(10, &n); // high-low transition - } - } - - if (ledcontrol) - LED_A_ON(); - SimulateTagLowFrequency(n, ledcontrol); - - if (ledcontrol) - LED_A_OFF(); -} - - -// loop to capture raw HID waveform then FSK demodulate the TAG ID from it -void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol) -{ - BYTE *dest = (BYTE *)BigBuf; - int m=0, n=0, i=0, idx=0, found=0, lastval=0; - DWORD hi=0, lo=0; - - FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz - FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_READER); - - // Connect the A/D to the peak-detected low-frequency path. - SetAdcMuxFor(GPIO_MUXSEL_LOPKD); - - // Give it a bit of time for the resonant antenna to settle. - SpinDelay(50); - - // Now set up the SSC to get the ADC samples that are now streaming at us. - FpgaSetupSsc(); - - for(;;) { - WDT_HIT(); - if (ledcontrol) - LED_A_ON(); - if(BUTTON_PRESS()) { - DbpString("Stopped"); - if (ledcontrol) - LED_A_OFF(); - return; - } - - i = 0; - m = sizeof(BigBuf); - memset(dest,128,m); - for(;;) { - if(SSC_STATUS & (SSC_STATUS_TX_READY)) { - SSC_TRANSMIT_HOLDING = 0x43; - if (ledcontrol) - LED_D_ON(); - } - if(SSC_STATUS & (SSC_STATUS_RX_READY)) { - dest[i] = (BYTE)SSC_RECEIVE_HOLDING; - // we don't care about actual value, only if it's more or less than a - // threshold essentially we capture zero crossings for later analysis - if(dest[i] < 127) dest[i] = 0; else dest[i] = 1; - i++; - if (ledcontrol) - LED_D_OFF(); - if(i >= m) { - break; - } - } - } - - // FSK demodulator - - // sync to first lo-hi transition - for( idx=1; idx>1)&0xffff); - /* if we're only looking for one tag */ - if (findone) - { - *high = hi; - *low = lo; - return; - } - hi=0; - lo=0; - found=0; - } - } - if (found) { - if (dest[idx] && (!dest[idx+1]) ) { - hi=(hi<<1)|(lo>>31); - lo=(lo<<1)|0; - } else if ( (!dest[idx]) && dest[idx+1]) { - hi=(hi<<1)|(lo>>31); - lo=(lo<<1)|1; - } else { - found=0; - hi=0; - lo=0; - } - idx++; - } - if ( dest[idx] && dest[idx+1] && dest[idx+2] && (!dest[idx+3]) && (!dest[idx+4]) && (!dest[idx+5]) ) - { - found=1; - idx+=6; - if (found && (hi|lo)) { - DbpString("TAG ID"); - DbpIntegers(hi, lo, (lo>>1)&0xffff); - /* if we're only looking for one tag */ - if (findone) - { - *high = hi; - *low = lo; - return; - } - hi=0; - lo=0; - found=0; - } - } - } - WDT_HIT(); - } -} +//----------------------------------------------------------------------------- +// This code is licensed to you under the terms of the GNU GPL, version 2 or, +// at your option, any later version. See the LICENSE.txt file for the text of +// the license. +//----------------------------------------------------------------------------- +// Miscellaneous routines for low frequency tag operations. +// Tags supported here so far are Texas Instruments (TI), HID +// Also routines for raw mode reading/simulating of LF waveform +//----------------------------------------------------------------------------- + +#include "proxmark3.h" +#include "apps.h" +#include "util.h" +#include "hitag2.h" +#include "crc16.h" +#include "string.h" +#include "lfdemod.h" +#include "lfsampling.h" +#include "protocols.h" +#include "usb_cdc.h" // for usb_poll_validate_length + +#ifndef SHORT_COIL +# define SHORT_COIL() LOW(GPIO_SSC_DOUT) +#endif +#ifndef OPEN_COIL +# define OPEN_COIL() HIGH(GPIO_SSC_DOUT) +#endif + +/** + * Function to do a modulation and then get samples. + * @param delay_off + * @param periods 0xFFFF0000 is period_0, 0x0000FFFF is period_1 + * @param useHighFreg + * @param command + */ +void ModThenAcquireRawAdcSamples125k(uint32_t delay_off, uint32_t periods, uint32_t useHighFreq, uint8_t *command) +{ + /* Make sure the tag is reset */ + FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + SpinDelay(200); + + uint16_t period_0 = periods >> 16; + uint16_t period_1 = periods & 0xFFFF; + + // 95 == 125 KHz 88 == 124.8 KHz + int divisor_used = (useHighFreq) ? 88 : 95; + sample_config sc = { 0,0,1, divisor_used, 0}; + setSamplingConfig(&sc); + + //clear read buffer + BigBuf_Clear_keep_EM(); + + LFSetupFPGAForADC(sc.divisor, 1); + + // And a little more time for the tag to fully power up + SpinDelay(50); + + // now modulate the reader field + while(*command != '\0' && *command != ' ') { + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + LED_D_OFF(); + WaitUS(delay_off); + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc.divisor); + + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); + LED_D_ON(); + if(*(command++) == '0') + WaitUS(period_0); + else + WaitUS(period_1); + } + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + LED_D_OFF(); + WaitUS(delay_off); + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc.divisor); + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); + + // now do the read + DoAcquisition_config(false); +} + +/* blank r/w tag data stream +...0000000000000000 01111111 +1010101010101010101010101010101010101010101010101010101010101010 +0011010010100001 +01111111 +101010101010101[0]000... + +[5555fe852c5555555555555555fe0000] +*/ +void ReadTItag(void) +{ + StartTicks(); + // some hardcoded initial params + // when we read a TI tag we sample the zerocross line at 2Mhz + // TI tags modulate a 1 as 16 cycles of 123.2Khz + // TI tags modulate a 0 as 16 cycles of 134.2Khz + #define FSAMPLE 2000000 + #define FREQLO 123200 + #define FREQHI 134200 + + signed char *dest = (signed char *)BigBuf_get_addr(); + uint16_t n = BigBuf_max_traceLen(); + // 128 bit shift register [shift3:shift2:shift1:shift0] + uint32_t shift3 = 0, shift2 = 0, shift1 = 0, shift0 = 0; + + int i, cycles=0, samples=0; + // how many sample points fit in 16 cycles of each frequency + uint32_t sampleslo = (FSAMPLE<<4)/FREQLO, sampleshi = (FSAMPLE<<4)/FREQHI; + // when to tell if we're close enough to one freq or another + uint32_t threshold = (sampleslo - sampleshi + 1)>>1; + + // TI tags charge at 134.2Khz + FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz + + // Place FPGA in passthrough mode, in this mode the CROSS_LO line + // connects to SSP_DIN and the SSP_DOUT logic level controls + // whether we're modulating the antenna (high) + // or listening to the antenna (low) + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_PASSTHRU); + + // get TI tag data into the buffer + AcquireTiType(); + + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + + for (i=0; i0) ) { + cycles++; + // after 16 cycles, measure the frequency + if (cycles>15) { + cycles=0; + samples=i-samples; // number of samples in these 16 cycles + + // TI bits are coming to us lsb first so shift them + // right through our 128 bit right shift register + shift0 = (shift0>>1) | (shift1 << 31); + shift1 = (shift1>>1) | (shift2 << 31); + shift2 = (shift2>>1) | (shift3 << 31); + shift3 >>= 1; + + // check if the cycles fall close to the number + // expected for either the low or high frequency + if ( (samples>(sampleslo-threshold)) && (samples<(sampleslo+threshold)) ) { + // low frequency represents a 1 + shift3 |= (1<<31); + } else if ( (samples>(sampleshi-threshold)) && (samples<(sampleshi+threshold)) ) { + // high frequency represents a 0 + } else { + // probably detected a gay waveform or noise + // use this as gaydar or discard shift register and start again + shift3 = shift2 = shift1 = shift0 = 0; + } + samples = i; + + // for each bit we receive, test if we've detected a valid tag + + // if we see 17 zeroes followed by 6 ones, we might have a tag + // remember the bits are backwards + if ( ((shift0 & 0x7fffff) == 0x7e0000) ) { + // if start and end bytes match, we have a tag so break out of the loop + if ( ((shift0>>16)&0xff) == ((shift3>>8)&0xff) ) { + cycles = 0xF0B; //use this as a flag (ugly but whatever) + break; + } + } + } + } + } + + // if flag is set we have a tag + if (cycles!=0xF0B) { + DbpString("Info: No valid tag detected."); + } else { + // put 64 bit data into shift1 and shift0 + shift0 = (shift0>>24) | (shift1 << 8); + shift1 = (shift1>>24) | (shift2 << 8); + + // align 16 bit crc into lower half of shift2 + shift2 = ((shift2>>24) | (shift3 << 8)) & 0x0ffff; + + // if r/w tag, check ident match + if (shift3 & (1<<15) ) { + DbpString("Info: TI tag is rewriteable"); + // only 15 bits compare, last bit of ident is not valid + if (((shift3 >> 16) ^ shift0) & 0x7fff ) { + DbpString("Error: Ident mismatch!"); + } else { + DbpString("Info: TI tag ident is valid"); + } + } else { + DbpString("Info: TI tag is readonly"); + } + + // WARNING the order of the bytes in which we calc crc below needs checking + // i'm 99% sure the crc algorithm is correct, but it may need to eat the + // bytes in reverse or something + // calculate CRC + uint32_t crc=0; + + crc = update_crc16(crc, (shift0)&0xff); + crc = update_crc16(crc, (shift0>>8)&0xff); + crc = update_crc16(crc, (shift0>>16)&0xff); + crc = update_crc16(crc, (shift0>>24)&0xff); + crc = update_crc16(crc, (shift1)&0xff); + crc = update_crc16(crc, (shift1>>8)&0xff); + crc = update_crc16(crc, (shift1>>16)&0xff); + crc = update_crc16(crc, (shift1>>24)&0xff); + + Dbprintf("Info: Tag data: %x%08x, crc=%x", (unsigned int)shift1, (unsigned int)shift0, (unsigned int)shift2 & 0xFFFF); + if (crc != (shift2&0xffff)) { + Dbprintf("Error: CRC mismatch, expected %x", (unsigned int)crc); + } else { + DbpString("Info: CRC is good"); + } + } + StopTicks(); +} + +void WriteTIbyte(uint8_t b) +{ + int i = 0; + + // modulate 8 bits out to the antenna + for (i=0; i<8; i++) + { + if ( b & ( 1 << i ) ) { + // stop modulating antenna 1ms + LOW(GPIO_SSC_DOUT); + WaitUS(1000); + // modulate antenna 1ms + HIGH(GPIO_SSC_DOUT); + WaitUS(1000); + } else { + // stop modulating antenna 1ms + LOW(GPIO_SSC_DOUT); + WaitUS(300); + // modulate antenna 1m + HIGH(GPIO_SSC_DOUT); + WaitUS(1700); + } + } +} + +void AcquireTiType(void) +{ + int i, j, n; + // tag transmission is <20ms, sampling at 2M gives us 40K samples max + // each sample is 1 bit stuffed into a uint32_t so we need 1250 uint32_t + #define TIBUFLEN 1250 + + // clear buffer + uint32_t *buf = (uint32_t *)BigBuf_get_addr(); + + //clear buffer now so it does not interfere with timing later + BigBuf_Clear_ext(false); + + // Set up the synchronous serial port + AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DIN; + AT91C_BASE_PIOA->PIO_ASR = GPIO_SSC_DIN; + + // steal this pin from the SSP and use it to control the modulation + AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT; + AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT; + + AT91C_BASE_SSC->SSC_CR = AT91C_SSC_SWRST; + AT91C_BASE_SSC->SSC_CR = AT91C_SSC_RXEN | AT91C_SSC_TXEN; + + // Sample at 2 Mbit/s, so TI tags are 16.2 vs. 14.9 clocks long + // 48/2 = 24 MHz clock must be divided by 12 + AT91C_BASE_SSC->SSC_CMR = 12; + + AT91C_BASE_SSC->SSC_RCMR = SSC_CLOCK_MODE_SELECT(0); + AT91C_BASE_SSC->SSC_RFMR = SSC_FRAME_MODE_BITS_IN_WORD(32) | AT91C_SSC_MSBF; + AT91C_BASE_SSC->SSC_TCMR = 0; + AT91C_BASE_SSC->SSC_TFMR = 0; + // iceman, FpgaSetupSsc() ?? the code above? can it be replaced? + LED_D_ON(); + + // modulate antenna + HIGH(GPIO_SSC_DOUT); + + // Charge TI tag for 50ms. + WaitMS(50); + + // stop modulating antenna and listen + LOW(GPIO_SSC_DOUT); + + LED_D_OFF(); + + i = 0; + for(;;) { + if(AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { + buf[i] = AT91C_BASE_SSC->SSC_RHR; // store 32 bit values in buffer + i++; if(i >= TIBUFLEN) break; + } + WDT_HIT(); + } + + // return stolen pin to SSP + AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DOUT; + AT91C_BASE_PIOA->PIO_ASR = GPIO_SSC_DIN | GPIO_SSC_DOUT; + + char *dest = (char *)BigBuf_get_addr(); + n = TIBUFLEN * 32; + + // unpack buffer + for (i = TIBUFLEN-1; i >= 0; i--) { + for (j = 0; j < 32; j++) { + if(buf[i] & (1 << j)) { + dest[--n] = 1; + } else { + dest[--n] = -1; + } + } + } +} + +// arguments: 64bit data split into 32bit idhi:idlo and optional 16bit crc +// if crc provided, it will be written with the data verbatim (even if bogus) +// if not provided a valid crc will be computed from the data and written. +void WriteTItag(uint32_t idhi, uint32_t idlo, uint16_t crc) +{ + StartTicks(); + FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + if(crc == 0) { + crc = update_crc16(crc, (idlo)&0xff); + crc = update_crc16(crc, (idlo>>8)&0xff); + crc = update_crc16(crc, (idlo>>16)&0xff); + crc = update_crc16(crc, (idlo>>24)&0xff); + crc = update_crc16(crc, (idhi)&0xff); + crc = update_crc16(crc, (idhi>>8)&0xff); + crc = update_crc16(crc, (idhi>>16)&0xff); + crc = update_crc16(crc, (idhi>>24)&0xff); + } + Dbprintf("Writing to tag: %x%08x, crc=%x", (unsigned int) idhi, (unsigned int) idlo, crc); + + // TI tags charge at 134.2Khz + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz + // Place FPGA in passthrough mode, in this mode the CROSS_LO line + // connects to SSP_DIN and the SSP_DOUT logic level controls + // whether we're modulating the antenna (high) + // or listening to the antenna (low) + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_PASSTHRU); + LED_A_ON(); + + // steal this pin from the SSP and use it to control the modulation + AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT; + AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT; + + // writing algorithm: + // a high bit consists of a field off for 1ms and field on for 1ms + // a low bit consists of a field off for 0.3ms and field on for 1.7ms + // initiate a charge time of 50ms (field on) then immediately start writing bits + // start by writing 0xBB (keyword) and 0xEB (password) + // then write 80 bits of data (or 64 bit data + 16 bit crc if you prefer) + // finally end with 0x0300 (write frame) + // all data is sent lsb first + // finish with 15ms programming time + + // modulate antenna + HIGH(GPIO_SSC_DOUT); + WaitMS(50); // charge time + + WriteTIbyte(0xbb); // keyword + WriteTIbyte(0xeb); // password + WriteTIbyte( (idlo )&0xff ); + WriteTIbyte( (idlo>>8 )&0xff ); + WriteTIbyte( (idlo>>16)&0xff ); + WriteTIbyte( (idlo>>24)&0xff ); + WriteTIbyte( (idhi )&0xff ); + WriteTIbyte( (idhi>>8 )&0xff ); + WriteTIbyte( (idhi>>16)&0xff ); + WriteTIbyte( (idhi>>24)&0xff ); // data hi to lo + WriteTIbyte( (crc )&0xff ); // crc lo + WriteTIbyte( (crc>>8 )&0xff ); // crc hi + WriteTIbyte(0x00); // write frame lo + WriteTIbyte(0x03); // write frame hi + HIGH(GPIO_SSC_DOUT); + WaitMS(50); // programming time + + LED_A_OFF(); + + // get TI tag data into the buffer + AcquireTiType(); + + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + DbpString("Now use `lf ti read` to check"); + StopTicks(); +} + +void SimulateTagLowFrequency(int period, int gap, int ledcontrol) +{ + int i = 0; + uint8_t *buf = BigBuf_get_addr(); + + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT); + //FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT | FPGA_LF_EDGE_DETECT_READER_FIELD); + //FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT | FPGA_LF_EDGE_DETECT_TOGGLE_MODE ); + + // set frequency, get values from 'lf config' command + sample_config *sc = getSamplingConfig(); + + if ( (sc->divisor == 1) || (sc->divisor < 0) || (sc->divisor > 255) ) + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 88); //134.8Khz + else if (sc->divisor == 0) + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz + else + FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc->divisor); + + SetAdcMuxFor(GPIO_MUXSEL_LOPKD); + + AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT | GPIO_SSC_CLK; + AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT; + AT91C_BASE_PIOA->PIO_ODR = GPIO_SSC_CLK; + + // power on antenna + // OPEN_COIL(); + // SpinDelay(50); + + for(;;) { + WDT_HIT(); + + if (ledcontrol) LED_D_ON(); + + // wait until SSC_CLK goes HIGH + // used as a simple detection of a reader field? + while(!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK)) { + WDT_HIT(); + if ( usb_poll_validate_length() || BUTTON_PRESS() ) + goto OUT; + } + + if(buf[i]) + OPEN_COIL(); + else + SHORT_COIL(); + + //wait until SSC_CLK goes LOW + while(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK) { + WDT_HIT(); + if ( usb_poll_validate_length() || BUTTON_PRESS() ) + goto OUT; + } + + i++; + if(i == period) { + i = 0; + if (gap) { + WDT_HIT(); + SHORT_COIL(); + SpinDelayUs(gap); + } + } + + if (ledcontrol) LED_D_OFF(); + } +OUT: + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + LED_D_OFF(); + DbpString("Simulation stopped"); + return; +} + +#define DEBUG_FRAME_CONTENTS 1 +void SimulateTagLowFrequencyBidir(int divisor, int t0) +{ +} + +// compose fc/8 fc/10 waveform (FSK2) +static void fc(int c, int *n) +{ + uint8_t *dest = BigBuf_get_addr(); + int idx; + + // for when we want an fc8 pattern every 4 logical bits + if(c==0) { + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + } + + // an fc/8 encoded bit is a bit pattern of 11110000 x6 = 48 samples + if(c==8) { + for (idx=0; idx<6; idx++) { + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + } + } + + // an fc/10 encoded bit is a bit pattern of 1111100000 x5 = 50 samples + if(c==10) { + for (idx=0; idx<5; idx++) { + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=1; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + dest[((*n)++)]=0; + } + } +} +// compose fc/X fc/Y waveform (FSKx) +static void fcAll(uint8_t fc, int *n, uint8_t clock, uint16_t *modCnt) +{ + uint8_t *dest = BigBuf_get_addr(); + uint8_t halfFC = fc/2; + uint8_t wavesPerClock = clock/fc; + uint8_t mod = clock % fc; //modifier + uint8_t modAdj = fc/mod; //how often to apply modifier + bool modAdjOk = !(fc % mod); //if (fc % mod==0) modAdjOk=TRUE; + // loop through clock - step field clock + for (uint8_t idx=0; idx < wavesPerClock; idx++){ + // put 1/2 FC length 1's and 1/2 0's per field clock wave (to create the wave) + memset(dest+(*n), 0, fc-halfFC); //in case of odd number use extra here + memset(dest+(*n)+(fc-halfFC), 1, halfFC); + *n += fc; + } + if (mod>0) (*modCnt)++; + if ((mod>0) && modAdjOk){ //fsk2 + if ((*modCnt % modAdj) == 0){ //if 4th 8 length wave in a rf/50 add extra 8 length wave + memset(dest+(*n), 0, fc-halfFC); + memset(dest+(*n)+(fc-halfFC), 1, halfFC); + *n += fc; + } + } + if (mod>0 && !modAdjOk){ //fsk1 + memset(dest+(*n), 0, mod-(mod/2)); + memset(dest+(*n)+(mod-(mod/2)), 1, mod/2); + *n += mod; + } +} + +// prepare a waveform pattern in the buffer based on the ID given then +// simulate a HID tag until the button is pressed +void CmdHIDsimTAG(int hi, int lo, int ledcontrol) +{ + FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + set_tracing(FALSE); + + int n = 0, i = 0; + /* + HID tag bitstream format + The tag contains a 44bit unique code. This is sent out MSB first in sets of 4 bits + A 1 bit is represented as 6 fc8 and 5 fc10 patterns + A 0 bit is represented as 5 fc10 and 6 fc8 patterns + A fc8 is inserted before every 4 bits + A special start of frame pattern is used consisting a0b0 where a and b are neither 0 + nor 1 bits, they are special patterns (a = set of 12 fc8 and b = set of 10 fc10) + */ + + if (hi > 0xFFF) { + DbpString("Tags can only have 44 bits. - USE lf simfsk for larger tags"); + return; + } + fc(0,&n); + // special start of frame marker containing invalid bit sequences + fc(8, &n); fc(8, &n); // invalid + fc(8, &n); fc(10, &n); // logical 0 + fc(10, &n); fc(10, &n); // invalid + fc(8, &n); fc(10, &n); // logical 0 + + WDT_HIT(); + // manchester encode bits 43 to 32 + for (i=11; i>=0; i--) { + if ((i%4)==3) fc(0,&n); + if ((hi>>i)&1) { + fc(10, &n); fc(8, &n); // low-high transition + } else { + fc(8, &n); fc(10, &n); // high-low transition + } + } + + WDT_HIT(); + // manchester encode bits 31 to 0 + for (i=31; i>=0; i--) { + if ((i%4)==3) fc(0,&n); + if ((lo>>i)&1) { + fc(10, &n); fc(8, &n); // low-high transition + } else { + fc(8, &n); fc(10, &n); // high-low transition + } + } + WDT_HIT(); + + if (ledcontrol) LED_A_ON(); + SimulateTagLowFrequency(n, 0, ledcontrol); + if (ledcontrol) LED_A_OFF(); +} + +// prepare a waveform pattern in the buffer based on the ID given then +// simulate a FSK tag until the button is pressed +// arg1 contains fcHigh and fcLow, arg2 contains invert and clock +void CmdFSKsimTAG(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream) +{ + FpgaDownloadAndGo(FPGA_BITSTREAM_LF); + + // free eventually allocated BigBuf memory + BigBuf_free(); BigBuf_Clear_ext(false); + clear_trace(); + set_tracing(FALSE); + + int ledcontrol = 1, n = 0, i = 0; + uint8_t fcHigh = arg1 >> 8; + uint8_t fcLow = arg1 & 0xFF; + uint16_t modCnt = 0; + uint8_t clk = arg2 & 0xFF; + uint8_t invert = (arg2 >> 8) & 1; + + for (i=0; i> 8) & 0xFF; + uint8_t encoding = arg1 & 0xFF; + uint8_t separator = arg2 & 1; + uint8_t invert = (arg2 >> 8) & 1; + + if (encoding == 2){ //biphase + uint8_t phase = 0; + for (i=0; i> 8; + uint8_t carrier = arg1 & 0xFF; + uint8_t invert = arg2 & 0xFF; + uint8_t curPhase = 0; + for (i=0; i0 && lo>0 && (size==96 || size==192)){ + // go over previously decoded manchester data and decode into usable tag ID + if (hi2 != 0){ //extra large HID tags 88/192 bits + Dbprintf("TAG ID: %x%08x%08x (%d)", + (unsigned int) hi2, + (unsigned int) hi, + (unsigned int) lo, + (unsigned int) (lo>>1) & 0xFFFF + ); + } else { //standard HID tags 44/96 bits + uint8_t bitlen = 0; + uint32_t fc = 0; + uint32_t cardnum = 0; + + if (((hi>>5)&1) == 1){//if bit 38 is set then < 37 bit format is used + uint32_t lo2=0; + lo2=(((hi & 31) << 12) | (lo>>20)); //get bits 21-37 to check for format len bit + uint8_t idx3 = 1; + while(lo2 > 1){ //find last bit set to 1 (format len bit) + lo2=lo2 >> 1; + idx3++; + } + bitlen = idx3+19; + fc =0; + cardnum=0; + if(bitlen == 26){ + cardnum = (lo>>1)&0xFFFF; + fc = (lo>>17)&0xFF; + } + if(bitlen == 37){ + cardnum = (lo>>1)&0x7FFFF; + fc = ((hi&0xF)<<12)|(lo>>20); + } + if(bitlen == 34){ + cardnum = (lo>>1)&0xFFFF; + fc= ((hi&1)<<15)|(lo>>17); + } + if(bitlen == 35){ + cardnum = (lo>>1)&0xFFFFF; + fc = ((hi&1)<<11)|(lo>>21); + } + } + else { //if bit 38 is not set then 37 bit format is used + bitlen= 37; + fc =0; + cardnum=0; + if(bitlen==37){ + cardnum = (lo>>1)&0x7FFFF; + fc = ((hi&0xF)<<12)|(lo>>20); + } + } + Dbprintf("TAG ID: %x%08x (%d) - Format Len: %dbit - FC: %d - Card: %d", + (unsigned int) hi, + (unsigned int) lo, + (unsigned int) (lo>>1) & 0xFFFF, + (unsigned int) bitlen, + (unsigned int) fc, + (unsigned int) cardnum); + } + if (findone){ + if (ledcontrol) LED_A_OFF(); + *high = hi; + *low = lo; + break; + } + // reset + } + hi2 = hi = lo = idx = 0; + WDT_HIT(); + } + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + DbpString("Stopped"); + if (ledcontrol) LED_A_OFF(); +} + +// loop to get raw HID waveform then FSK demodulate the TAG ID from it +void CmdAWIDdemodFSK(int findone, int *high, int *low, int ledcontrol) +{ + uint8_t *dest = BigBuf_get_addr(); + size_t size; + int idx=0; + //clear read buffer + BigBuf_Clear_keep_EM(); + // Configure to go in 125Khz listen mode + LFSetupFPGAForADC(95, true); + + while(!BUTTON_PRESS() && !usb_poll_validate_length()) { + + WDT_HIT(); + if (ledcontrol) LED_A_ON(); + + DoAcquisition_default(-1,true); + // FSK demodulator + size = 50*128*2; //big enough to catch 2 sequences of largest format + idx = AWIDdemodFSK(dest, &size); + + if (idx<=0 || size!=96) continue; + // Index map + // 0 10 20 30 40 50 60 + // | | | | | | | + // 01234567 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 - to 96 + // ----------------------------------------------------------------------------- + // 00000001 000 1 110 1 101 1 011 1 101 1 010 0 000 1 000 1 010 0 001 0 110 1 100 0 000 1 000 1 + // premable bbb o bbb o bbw o fff o fff o ffc o ccc o ccc o ccc o ccc o ccc o wxx o xxx o xxx o - to 96 + // |---26 bit---| |-----117----||-------------142-------------| + // b = format bit len, o = odd parity of last 3 bits + // f = facility code, c = card number + // w = wiegand parity + // (26 bit format shown) + + //get raw ID before removing parities + uint32_t rawLo = bytebits_to_byte(dest+idx+64,32); + uint32_t rawHi = bytebits_to_byte(dest+idx+32,32); + uint32_t rawHi2 = bytebits_to_byte(dest+idx,32); + + size = removeParity(dest, idx+8, 4, 1, 88); + if (size != 66) continue; + + // Index map + // 0 10 20 30 40 50 60 + // | | | | | | | + // 01234567 8 90123456 7890123456789012 3 456789012345678901234567890123456 + // ----------------------------------------------------------------------------- + // 00011010 1 01110101 0000000010001110 1 000000000000000000000000000000000 + // bbbbbbbb w ffffffff cccccccccccccccc w xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx + // |26 bit| |-117--| |-----142------| + // + // 00110010 0 0000011111010000000000000001000100101000100001111 0 00000000 + // bbbbbbbb w ffffffffffffffffccccccccccccccccccccccccccccccccc w xxxxxxxx + // |50 bit| |----4000------||-----------2248975-------------| + // + // b = format bit len, o = odd parity of last 3 bits + // f = facility code, c = card number + // w = wiegand parity + + uint32_t fc = 0; + uint32_t cardnum = 0; + uint32_t code1 = 0; + uint32_t code2 = 0; + uint8_t fmtLen = bytebits_to_byte(dest,8); + switch(fmtLen) { + case 26: + fc = bytebits_to_byte(dest + 9, 8); + cardnum = bytebits_to_byte(dest + 17, 16); + code1 = bytebits_to_byte(dest + 8,fmtLen); + Dbprintf("AWID Found - BitLength: %d, FC: %d, Card: %u - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, fc, cardnum, code1, rawHi2, rawHi, rawLo); + break; + case 50: + fc = bytebits_to_byte(dest + 9, 16); + cardnum = bytebits_to_byte(dest + 25, 32); + code1 = bytebits_to_byte(dest + 8, (fmtLen-32) ); + code2 = bytebits_to_byte(dest + 8 + (fmtLen-32), 32); + Dbprintf("AWID Found - BitLength: %d, FC: %d, Card: %u - Wiegand: %x%08x, Raw: %08x%08x%08x", fmtLen, fc, cardnum, code1, code2, rawHi2, rawHi, rawLo); + break; + default: + if (fmtLen > 32 ) { + cardnum = bytebits_to_byte(dest+8+(fmtLen-17), 16); + code1 = bytebits_to_byte(dest+8,fmtLen-32); + code2 = bytebits_to_byte(dest+8+(fmtLen-32),32); + Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%u) - Wiegand: %x%08x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, code2, rawHi2, rawHi, rawLo); + } else { + cardnum = bytebits_to_byte(dest+8+(fmtLen-17), 16); + code1 = bytebits_to_byte(dest+8,fmtLen); + Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%u) - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, rawHi2, rawHi, rawLo); + } + break; + } + if (findone) + break; + + idx = 0; + WDT_HIT(); + } + + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + DbpString("Stopped"); + if (ledcontrol) LED_A_OFF(); +} + +void CmdEM410xdemod(int findone, int *high, int *low, int ledcontrol) +{ + uint8_t *dest = BigBuf_get_addr(); + + size_t size=0, idx=0; + int clk=0, invert=0, errCnt=0, maxErr=20; + uint32_t hi=0; + uint64_t lo=0; + //clear read buffer + BigBuf_Clear_keep_EM(); + // Configure to go in 125Khz listen mode + LFSetupFPGAForADC(95, true); + + while(!BUTTON_PRESS() && !usb_poll_validate_length()) { + + WDT_HIT(); + if (ledcontrol) LED_A_ON(); + + DoAcquisition_default(-1,true); + size = BigBuf_max_traceLen(); + //askdemod and manchester decode + if (size > 16385) size = 16385; //big enough to catch 2 sequences of largest format + errCnt = askdemod(dest, &size, &clk, &invert, maxErr, 0, 1); + WDT_HIT(); + + if (errCnt<0) continue; + + errCnt = Em410xDecode(dest, &size, &idx, &hi, &lo); + if (errCnt){ + if (size>64){ + Dbprintf("EM XL TAG ID: %06x%08x%08x - (%05d_%03d_%08d)", + hi, + (uint32_t)(lo>>32), + (uint32_t)lo, + (uint32_t)(lo&0xFFFF), + (uint32_t)((lo>>16LL) & 0xFF), + (uint32_t)(lo & 0xFFFFFF)); + } else { + Dbprintf("EM TAG ID: %02x%08x - (%05d_%03d_%08d)", + (uint32_t)(lo>>32), + (uint32_t)lo, + (uint32_t)(lo&0xFFFF), + (uint32_t)((lo>>16LL) & 0xFF), + (uint32_t)(lo & 0xFFFFFF)); + } + + if (findone){ + if (ledcontrol) LED_A_OFF(); + *high=lo>>32; + *low=lo & 0xFFFFFFFF; + break; + } + } + WDT_HIT(); + hi = lo = size = idx = 0; + clk = invert = errCnt = 0; + } + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + DbpString("Stopped"); + if (ledcontrol) LED_A_OFF(); +} + +void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol) +{ + uint8_t *dest = BigBuf_get_addr(); + int idx=0; + uint32_t code=0, code2=0; + uint8_t version=0; + uint8_t facilitycode=0; + uint16_t number=0; + uint8_t crc = 0; + uint16_t calccrc = 0; + + //clear read buffer + BigBuf_Clear_keep_EM(); + + // Configure to go in 125Khz listen mode + LFSetupFPGAForADC(95, true); + + while(!BUTTON_PRESS() && !usb_poll_validate_length()) { + WDT_HIT(); + if (ledcontrol) LED_A_ON(); + DoAcquisition_default(-1,true); + //fskdemod and get start index + WDT_HIT(); + idx = IOdemodFSK(dest, BigBuf_max_traceLen()); + if (idx<0) continue; + //valid tag found + + //Index map + //0 10 20 30 40 50 60 + //| | | | | | | + //01234567 8 90123456 7 89012345 6 78901234 5 67890123 4 56789012 3 45678901 23 + //----------------------------------------------------------------------------- + //00000000 0 11110000 1 facility 1 version* 1 code*one 1 code*two 1 checksum 11 + // + //Checksum: + //00000000 0 11110000 1 11100000 1 00000001 1 00000011 1 10110110 1 01110101 11 + //preamble F0 E0 01 03 B6 75 + // How to calc checksum, + // http://www.proxmark.org/forum/viewtopic.php?id=364&p=6 + // F0 + E0 + 01 + 03 + B6 = 28A + // 28A & FF = 8A + // FF - 8A = 75 + // Checksum: 0x75 + //XSF(version)facility:codeone+codetwo + //Handle the data + // if(findone){ //only print binary if we are doing one + // Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx], dest[idx+1], dest[idx+2],dest[idx+3],dest[idx+4],dest[idx+5],dest[idx+6],dest[idx+7],dest[idx+8]); + // Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+9], dest[idx+10],dest[idx+11],dest[idx+12],dest[idx+13],dest[idx+14],dest[idx+15],dest[idx+16],dest[idx+17]); + // Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+18],dest[idx+19],dest[idx+20],dest[idx+21],dest[idx+22],dest[idx+23],dest[idx+24],dest[idx+25],dest[idx+26]); + // Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+27],dest[idx+28],dest[idx+29],dest[idx+30],dest[idx+31],dest[idx+32],dest[idx+33],dest[idx+34],dest[idx+35]); + // Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+36],dest[idx+37],dest[idx+38],dest[idx+39],dest[idx+40],dest[idx+41],dest[idx+42],dest[idx+43],dest[idx+44]); + // Dbprintf("%d%d%d%d%d%d%d%d %d",dest[idx+45],dest[idx+46],dest[idx+47],dest[idx+48],dest[idx+49],dest[idx+50],dest[idx+51],dest[idx+52],dest[idx+53]); + // Dbprintf("%d%d%d%d%d%d%d%d %d%d",dest[idx+54],dest[idx+55],dest[idx+56],dest[idx+57],dest[idx+58],dest[idx+59],dest[idx+60],dest[idx+61],dest[idx+62],dest[idx+63]); + // } + code = bytebits_to_byte(dest+idx,32); + code2 = bytebits_to_byte(dest+idx+32,32); + version = bytebits_to_byte(dest+idx+27,8); //14,4 + facilitycode = bytebits_to_byte(dest+idx+18,8); + number = (bytebits_to_byte(dest+idx+36,8)<<8)|(bytebits_to_byte(dest+idx+45,8)); //36,9 + + crc = bytebits_to_byte(dest+idx+54,8); + for (uint8_t i=1; i<6; ++i) + calccrc += bytebits_to_byte(dest+idx+9*i,8); + calccrc &= 0xff; + calccrc = 0xff - calccrc; + + char *crcStr = (crc == calccrc) ? "ok":"!crc"; + + Dbprintf("IO Prox XSF(%02d)%02x:%05d (%08x%08x) [%02x %s]",version,facilitycode,number,code,code2, crc, crcStr); + // if we're only looking for one tag + if (findone){ + if (ledcontrol) LED_A_OFF(); + *high=code; + *low=code2; + break; + } + code=code2=0; + version=facilitycode=0; + number=0; + idx=0; + + WDT_HIT(); + } + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + DbpString("Stopped"); + if (ledcontrol) LED_A_OFF(); +} + +/*------------------------------ + * T5555/T5557/T5567/T5577 routines + *------------------------------ + * NOTE: T55x7/T5555 configuration register definitions moved to protocols.h + * + * Relevant communication times in microsecond + * To compensate antenna falling times shorten the write times + * and enlarge the gap ones. + * Q5 tags seems to have issues when these values changes. + */ + +#define START_GAP 50*8 // was 250 // SPEC: 1*8 to 50*8 - typ 15*8 (15fc) +#define WRITE_GAP 20*8 // was 160 // SPEC: 1*8 to 20*8 - typ 10*8 (10fc) +#define WRITE_0 18*8 // was 144 // SPEC: 16*8 to 32*8 - typ 24*8 (24fc) +#define WRITE_1 54*8 // was 400 // SPEC: 48*8 to 64*8 - typ 56*8 (56fc) 432 for T55x7; 448 for E5550 +#define READ_GAP 15*8 + +// VALUES TAKEN FROM EM4x function: SendForward +// START_GAP = 440; (55*8) cycles at 125Khz (8us = 1cycle) +// WRITE_GAP = 128; (16*8) +// WRITE_1 = 256 32*8; (32*8) + +// These timings work for 4469/4269/4305 (with the 55*8 above) +// WRITE_0 = 23*8 , 9*8 + +// Sam7s has several timers, we will use the source TIMER_CLOCK1 (aka AT91C_TC_CLKS_TIMER_DIV1_CLOCK) +// TIMER_CLOCK1 = MCK/2, MCK is running at 48 MHz, Timer is running at 48/2 = 24 MHz +// Hitag units (T0) have duration of 8 microseconds (us), which is 1/125000 per second (carrier) +// T0 = TIMER_CLOCK1 / 125000 = 192 +// 1 Cycle = 8 microseconds(us) == 1 field clock + +// new timer: +// = 1us = 1.5ticks +// 1fc = 8us = 12ticks +void TurnReadLFOn(uint32_t delay) { + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); + + // measure antenna strength. + //int adcval = ((MAX_ADC_LF_VOLTAGE * AvgAdc(ADC_CHAN_LF)) >> 10); + + // Give it a bit of time for the resonant antenna to settle. + WaitUS(delay); +} + +// Write one bit to card +void T55xxWriteBit(int bit) { + if (!bit) + TurnReadLFOn(WRITE_0); + else + TurnReadLFOn(WRITE_1); + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + WaitUS(WRITE_GAP); +} + +// Send T5577 reset command then read stream (see if we can identify the start of the stream) +void T55xxResetRead(void) { + LED_A_ON(); + //clear buffer now so it does not interfere with timing later + BigBuf_Clear_keep_EM(); + + // Set up FPGA, 125kHz + LFSetupFPGAForADC(95, true); + + // Trigger T55x7 in mode. + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + WaitUS(START_GAP); + + // reset tag - op code 00 + T55xxWriteBit(0); + T55xxWriteBit(0); + + // Turn field on to read the response + TurnReadLFOn(READ_GAP); + + // Acquisition + doT55x7Acquisition(BigBuf_max_traceLen()); + + // Turn the field off + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + cmd_send(CMD_ACK,0,0,0,0,0); + LED_A_OFF(); +} + +// Write one card block in page 0, no lock +void T55xxWriteBlockExt(uint32_t Data, uint8_t Block, uint32_t Pwd, uint8_t arg) { + LED_A_ON(); + bool PwdMode = arg & 0x1; + uint8_t Page = (arg & 0x2)>>1; + uint32_t i = 0; + + // Set up FPGA, 125kHz + LFSetupFPGAForADC(95, true); + + // Trigger T55x7 in mode. + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + WaitUS(START_GAP); + + // Opcode 10 + T55xxWriteBit(1); + T55xxWriteBit(Page); //Page 0 + if (PwdMode){ + // Send Pwd + for (i = 0x80000000; i != 0; i >>= 1) + T55xxWriteBit(Pwd & i); + } + // Send Lock bit + T55xxWriteBit(0); + + // Send Data + for (i = 0x80000000; i != 0; i >>= 1) + T55xxWriteBit(Data & i); + + // Send Block number + for (i = 0x04; i != 0; i >>= 1) + T55xxWriteBit(Block & i); + + // Perform write (nominal is 5.6 ms for T55x7 and 18ms for E5550, + // so wait a little more) + TurnReadLFOn(20 * 1000); + + //could attempt to do a read to confirm write took + // as the tag should repeat back the new block + // until it is reset, but to confirm it we would + // need to know the current block 0 config mode + + // turn field off + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + LED_A_OFF(); +} + +// Write one card block in page 0, no lock +void T55xxWriteBlock(uint32_t Data, uint8_t Block, uint32_t Pwd, uint8_t arg) { + T55xxWriteBlockExt(Data, Block, Pwd, arg); + cmd_send(CMD_ACK,0,0,0,0,0); +} + +// Read one card block in page [page] +void T55xxReadBlock(uint16_t arg0, uint8_t Block, uint32_t Pwd) { + LED_A_ON(); + bool PwdMode = arg0 & 0x1; + uint8_t Page = (arg0 & 0x2) >> 1; + uint32_t i = 0; + bool RegReadMode = (Block == 0xFF); + + //clear buffer now so it does not interfere with timing later + BigBuf_Clear_keep_EM(); + + //make sure block is at max 7 + Block &= 0x7; + + // Set up FPGA, 125kHz to power up the tag + LFSetupFPGAForADC(95, true); + SpinDelay(3); + + // Trigger T55x7 Direct Access Mode with start gap + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + WaitUS(START_GAP); + + // Opcode 1[page] + T55xxWriteBit(1); + T55xxWriteBit(Page); //Page 0 + + if (PwdMode){ + // Send Pwd + for (i = 0x80000000; i != 0; i >>= 1) + T55xxWriteBit(Pwd & i); + } + // Send a zero bit separation + T55xxWriteBit(0); + + // Send Block number (if direct access mode) + if (!RegReadMode) + for (i = 0x04; i != 0; i >>= 1) + T55xxWriteBit(Block & i); + + // Turn field on to read the response + TurnReadLFOn(READ_GAP); + + // Acquisition + doT55x7Acquisition(12000); + + // Turn the field off + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + cmd_send(CMD_ACK,0,0,0,0,0); + LED_A_OFF(); +} + +void T55xxWakeUp(uint32_t Pwd){ + LED_B_ON(); + uint32_t i = 0; + + // Set up FPGA, 125kHz + LFSetupFPGAForADC(95, true); + + // Trigger T55x7 Direct Access Mode + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); + WaitUS(START_GAP); + + // Opcode 10 + T55xxWriteBit(1); + T55xxWriteBit(0); //Page 0 + + // Send Pwd + for (i = 0x80000000; i != 0; i >>= 1) + T55xxWriteBit(Pwd & i); + + // Turn and leave field on to let the begin repeating transmission + TurnReadLFOn(20*1000); +} + +/*-------------- Cloning routines -----------*/ +void WriteT55xx(uint32_t *blockdata, uint8_t startblock, uint8_t numblocks) { + // write last block first and config block last (if included) + for (uint8_t i = numblocks+startblock; i > startblock; i--) + T55xxWriteBlockExt(blockdata[i-1], i-1, 0, 0); +} + +// Copy HID id to card and setup block 0 config +void CopyHIDtoT55x7(uint32_t hi2, uint32_t hi, uint32_t lo, uint8_t longFMT) { + uint32_t data[] = {0,0,0,0,0,0,0}; + uint8_t last_block = 0; + + if (longFMT){ + // Ensure no more than 84 bits supplied + if (hi2 > 0xFFFFF) { + DbpString("Tags can only have 84 bits."); + return; + } + // Build the 6 data blocks for supplied 84bit ID + last_block = 6; + // load preamble (1D) & long format identifier (9E manchester encoded) + data[1] = 0x1D96A900 | (manchesterEncode2Bytes((hi2 >> 16) & 0xF) & 0xFF); + // load raw id from hi2, hi, lo to data blocks (manchester encoded) + data[2] = manchesterEncode2Bytes(hi2 & 0xFFFF); + data[3] = manchesterEncode2Bytes(hi >> 16); + data[4] = manchesterEncode2Bytes(hi & 0xFFFF); + data[5] = manchesterEncode2Bytes(lo >> 16); + data[6] = manchesterEncode2Bytes(lo & 0xFFFF); + } else { + // Ensure no more than 44 bits supplied + if (hi > 0xFFF) { + DbpString("Tags can only have 44 bits."); + return; + } + // Build the 3 data blocks for supplied 44bit ID + last_block = 3; + // load preamble + data[1] = 0x1D000000 | (manchesterEncode2Bytes(hi) & 0xFFFFFF); + data[2] = manchesterEncode2Bytes(lo >> 16); + data[3] = manchesterEncode2Bytes(lo & 0xFFFF); + } + // load chip config block + data[0] = T55x7_BITRATE_RF_50 | T55x7_MODULATION_FSK2a | last_block << T55x7_MAXBLOCK_SHIFT; + + //TODO add selection of chip for Q5 or T55x7 + // data[0] = (((50-2)/2)<>= 1; + } else { + rev_id = (rev_id << 1) | (id_hi & 1); + id_hi >>= 1; + } + } + + for (i = 0; i < EM410X_ID_LENGTH; ++i) { + id_bit = rev_id & 1; + + if (i % 4 == 0) { + // Don't write row parity bit at start of parsing + if (i) + id = (id << 1) | r_parity; + // Start counting parity for new row + r_parity = id_bit; + } else { + // Count row parity + r_parity ^= id_bit; + } + + // First elements in column? + if (i < 4) + // Fill out first elements + c_parity[i] = id_bit; + else + // Count column parity + c_parity[i % 4] ^= id_bit; + + // Insert ID bit + id = (id << 1) | id_bit; + rev_id >>= 1; + } + + // Insert parity bit of last row + id = (id << 1) | r_parity; + + // Fill out column parity at the end of tag + for (i = 0; i < 4; ++i) + id = (id << 1) | c_parity[i]; + + // Add stop bit + id <<= 1; + + Dbprintf("Started writing %s tag ...", card ? "T55x7":"T5555"); + LED_D_ON(); + + // Write EM410x ID + uint32_t data[] = {0, (uint32_t)(id>>32), (uint32_t)(id & 0xFFFFFFFF)}; + + clock = (card & 0xFF00) >> 8; + clock = (clock == 0) ? 64 : clock; + Dbprintf("Clock rate: %d", clock); + if (card & 0xFF) { //t55x7 + clock = GetT55xxClockBit(clock); + if (clock == 0) { + Dbprintf("Invalid clock rate: %d", clock); + return; + } + data[0] = clock | T55x7_MODULATION_MANCHESTER | (2 << T55x7_MAXBLOCK_SHIFT); + } else { //t5555 (Q5) + clock = (clock-2)>>1; //n = (RF-2)/2 + data[0] = (clock << T5555_BITRATE_SHIFT) | T5555_MODULATION_MANCHESTER | (2 << T5555_MAXBLOCK_SHIFT); + } + + WriteT55xx(data, 0, 3); + + LED_D_OFF(); + Dbprintf("Tag %s written with 0x%08x%08x\n", + card ? "T55x7":"T5555", + (uint32_t)(id >> 32), + (uint32_t)id); +} + +//----------------------------------- +// EM4469 / EM4305 routines +//----------------------------------- +#define FWD_CMD_LOGIN 0xC //including the even parity, binary mirrored +#define FWD_CMD_WRITE 0xA +#define FWD_CMD_READ 0x9 +#define FWD_CMD_DISABLE 0x5 + +uint8_t forwardLink_data[64]; //array of forwarded bits +uint8_t * forward_ptr; //ptr for forward message preparation +uint8_t fwd_bit_sz; //forwardlink bit counter +uint8_t * fwd_write_ptr; //forwardlink bit pointer + +//==================================================================== +// prepares command bits +// see EM4469 spec +//==================================================================== +//-------------------------------------------------------------------- +// VALUES TAKEN FROM EM4x function: SendForward +// START_GAP = 440; (55*8) cycles at 125Khz (8us = 1cycle) +// WRITE_GAP = 128; (16*8) +// WRITE_1 = 256 32*8; (32*8) + +// These timings work for 4469/4269/4305 (with the 55*8 above) +// WRITE_0 = 23*8 , 9*8 + +uint8_t Prepare_Cmd( uint8_t cmd ) { + + *forward_ptr++ = 0; //start bit + *forward_ptr++ = 0; //second pause for 4050 code + + *forward_ptr++ = cmd; + cmd >>= 1; + *forward_ptr++ = cmd; + cmd >>= 1; + *forward_ptr++ = cmd; + cmd >>= 1; + *forward_ptr++ = cmd; + + return 6; //return number of emited bits +} + +//==================================================================== +// prepares address bits +// see EM4469 spec +//==================================================================== +uint8_t Prepare_Addr( uint8_t addr ) { + + register uint8_t line_parity; + + uint8_t i; + line_parity = 0; + for(i=0;i<6;i++) { + *forward_ptr++ = addr; + line_parity ^= addr; + addr >>= 1; + } + + *forward_ptr++ = (line_parity & 1); + + return 7; //return number of emited bits +} + +//==================================================================== +// prepares data bits intreleaved with parity bits +// see EM4469 spec +//==================================================================== +uint8_t Prepare_Data( uint16_t data_low, uint16_t data_hi) { + + register uint8_t line_parity; + register uint8_t column_parity; + register uint8_t i, j; + register uint16_t data; + + data = data_low; + column_parity = 0; + + for(i=0; i<4; i++) { + line_parity = 0; + for(j=0; j<8; j++) { + line_parity ^= data; + column_parity ^= (data & 1) << j; + *forward_ptr++ = data; + data >>= 1; + } + *forward_ptr++ = line_parity; + if(i == 1) + data = data_hi; + } + + for(j=0; j<8; j++) { + *forward_ptr++ = column_parity; + column_parity >>= 1; + } + *forward_ptr = 0; + + return 45; //return number of emited bits +} + +//==================================================================== +// Forward Link send function +// Requires: forwarLink_data filled with valid bits (1 bit per byte) +// fwd_bit_count set with number of bits to be sent +//==================================================================== +void SendForward(uint8_t fwd_bit_count) { + + fwd_write_ptr = forwardLink_data; + fwd_bit_sz = fwd_bit_count; + + LED_D_ON(); + + // Set up FPGA, 125kHz + LFSetupFPGAForADC(95, true); + + // force 1st mod pulse (start gap must be longer for 4305) + fwd_bit_sz--; //prepare next bit modulation + fwd_write_ptr++; + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + WaitUS(55*8); //55 cycles off (8us each)for 4305 // ICEMAN: problem with (us) clock is 21.3us increments + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);//field on + WaitUS(16*8); //16 cycles on (8us each) // ICEMAN: problem with (us) clock is 21.3us increments + + // now start writting + while(fwd_bit_sz-- > 0) { //prepare next bit modulation + if(((*fwd_write_ptr++) & 1) == 1) + WaitUS(32*8); //32 cycles at 125Khz (8us each) // ICEMAN: problem with (us) clock is 21.3us increments + else { + //These timings work for 4469/4269/4305 (with the 55*8 above) + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + WaitUS(16*8); //16-4 cycles off (8us each) // ICEMAN: problem with (us) clock is 21.3us increments + FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);//field on + WaitUS(16*8); //16 cycles on (8us each) // ICEMAN: problem with (us) clock is 21.3us increments + } + } +} + +void EM4xLogin(uint32_t Password) { + + uint8_t fwd_bit_count; + forward_ptr = forwardLink_data; + fwd_bit_count = Prepare_Cmd( FWD_CMD_LOGIN ); + fwd_bit_count += Prepare_Data( Password&0xFFFF, Password>>16 ); + SendForward(fwd_bit_count); + + //Wait for command to complete + WaitMS(20); +} + +void EM4xReadWord(uint8_t Address, uint32_t Pwd, uint8_t PwdMode) { + + uint8_t fwd_bit_count; + uint8_t *dest = BigBuf_get_addr(); + uint16_t bufsize = BigBuf_max_traceLen(); // ICEMAN: this tries to fill up all tracelog space + uint32_t i = 0; + + // Clear destination buffer before sending the command + BigBuf_Clear_ext(false); + + //If password mode do login + if (PwdMode == 1) EM4xLogin(Pwd); + + forward_ptr = forwardLink_data; + fwd_bit_count = Prepare_Cmd( FWD_CMD_READ ); + fwd_bit_count += Prepare_Addr( Address ); + + SendForward(fwd_bit_count); + + // Now do the acquisition + // ICEMAN, change to the one in lfsampling.c + i = 0; + for(;;) { + if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_TXRDY) { + AT91C_BASE_SSC->SSC_THR = 0x43; + } + if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) { + dest[i] = (uint8_t)AT91C_BASE_SSC->SSC_RHR; + ++i; + if (i >= bufsize) break; + } + } + + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + cmd_send(CMD_ACK,0,0,0,0,0); + LED_D_OFF(); +} + +void EM4xWriteWord(uint32_t Data, uint8_t Address, uint32_t Pwd, uint8_t PwdMode) { + + uint8_t fwd_bit_count; + + //If password mode do login + if (PwdMode == 1) EM4xLogin(Pwd); + + forward_ptr = forwardLink_data; + fwd_bit_count = Prepare_Cmd( FWD_CMD_WRITE ); + fwd_bit_count += Prepare_Addr( Address ); + fwd_bit_count += Prepare_Data( Data&0xFFFF, Data>>16 ); + + SendForward(fwd_bit_count); + + //Wait for write to complete + WaitMS(20); + FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off + LED_D_OFF(); +}