X-Git-Url: https://git.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/1c38843b3f0b808f06a468162667bf96d235363d..489e1745415038d3d315247f8cdad080c14eb95b:/fpga/lo_read.v?ds=sidebyside

diff --git a/fpga/lo_read.v b/fpga/lo_read.v
index 8dce4dda..e6f245ca 100644
--- a/fpga/lo_read.v
+++ b/fpga/lo_read.v
@@ -1,103 +1,103 @@
-//-----------------------------------------------------------------------------
-// The way that we connect things in low-frequency read mode. In this case
-// we are generating the unmodulated low frequency carrier.
-// The A/D samples at that same rate and the result is serialized.
-//
-// Jonathan Westhues, April 2006
-//-----------------------------------------------------------------------------
-
-module lo_read(
-    pck0, ck_1356meg, ck_1356megb,
-    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
-    adc_d, adc_clk,
-    ssp_frame, ssp_din, ssp_dout, ssp_clk,
-    cross_hi, cross_lo,
-    dbg,
-    lo_is_125khz, divisor
-);
-    input pck0, ck_1356meg, ck_1356megb;
-    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
-    input [7:0] adc_d;
-    output adc_clk;
-    input ssp_dout;
-    output ssp_frame, ssp_din, ssp_clk;
-    input cross_hi, cross_lo;
-    output dbg;
-    input lo_is_125khz; // redundant signal, no longer used anywhere
-    input [7:0] divisor;
-
-reg [7:0] to_arm_shiftreg;
-reg [7:0] pck_divider;
-reg ant_lo;
-
-// this task runs on the rising egde of pck0 clock (24Mhz) and creates ant_lo
-// which is high for (divisor+1) pck0 cycles and low for the same duration
-// ant_lo is therefore a 50% duty cycle clock signal with a frequency of
-// 12Mhz/(divisor+1) which drives the antenna as well as the ADC clock adc_clk
-always @(posedge pck0)
-begin
-	if(pck_divider == divisor[7:0])
-		begin
-			pck_divider <= 8'd0;
-			ant_lo = !ant_lo;
-		end
-	else
-	begin
-		pck_divider <= pck_divider + 1;
-	end
-end
-
-// this task also runs at pck0 frequency (24Mhz) and is used to serialize
-// the ADC output which is then clocked into the ARM SSP.
-
-// because ant_lo always transitions when pck_divider = 0 we use the
-// pck_divider counter to sync our other signals off it
-// we read the ADC value when pck_divider=7 and shift it out on counts 8..15
-always @(posedge pck0)
-begin
-	if((pck_divider == 8'd7) && !ant_lo)
-        to_arm_shiftreg <= adc_d;
-    else
-	begin
-        to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
-		// simulation showed a glitch occuring due to the LSB of the shifter
-		// not being set as we shift bits out
-		// this ensures the ssp_din remains low after a transfer and suppresses
-		// the glitch that would occur when the last data shifted out ended in
-		// a 1 bit and the next data shifted out started with a 0 bit
-        to_arm_shiftreg[0] <= 1'b0;
-	end
-end
-
-// ADC samples on falling edge of adc_clk, data available on the rising edge
-
-// example of ssp transfer of binary value 1100101
-// start of transfer is indicated by the rise of the ssp_frame signal
-// ssp_din changes on the rising edge of the ssp_clk clock and is clocked into
-// the ARM by the falling edge of ssp_clk
-//             _______________________________
-// ssp_frame__|                               |__
-//             _______         ___     ___
-// ssp_din  __|       |_______|   |___|   |______
-//         _   _   _   _   _   _   _   _   _   _
-// ssp_clk  |_| |_| |_| |_| |_| |_| |_| |_| |_| |_
-
-// serialized SSP data is gated by ant_lo to suppress unwanted signal
-assign ssp_din = to_arm_shiftreg[7] && !ant_lo;
-// SSP clock always runs at 24Mhz
-assign ssp_clk = pck0;
-// SSP frame is gated by ant_lo and goes high when pck_divider=8..15
-assign ssp_frame = (pck_divider[7:3] == 5'd1) && !ant_lo;
-// unused signals tied low
-assign pwr_hi = 1'b0;
-assign pwr_oe1 = 1'b0;
-assign pwr_oe2 = 1'b0;
-assign pwr_oe3 = 1'b0;
-assign pwr_oe4 = 1'b0;
-// this is the antenna driver signal
-assign pwr_lo = ant_lo;
-// ADC clock out of phase with antenna driver
-assign adc_clk = ~ant_lo;
-// ADC clock also routed to debug pin
-assign dbg = adc_clk;
-endmodule
+//-----------------------------------------------------------------------------
+// The way that we connect things in low-frequency read mode. In this case
+// we are generating the unmodulated low frequency carrier.
+// The A/D samples at that same rate and the result is serialized.
+//
+// Jonathan Westhues, April 2006
+//-----------------------------------------------------------------------------
+
+module lo_read(
+    pck0, ck_1356meg, ck_1356megb,
+    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
+    adc_d, adc_clk,
+    ssp_frame, ssp_din, ssp_dout, ssp_clk,
+    cross_hi, cross_lo,
+    dbg,
+    lo_is_125khz, divisor
+);
+    input pck0, ck_1356meg, ck_1356megb;
+    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
+    input [7:0] adc_d;
+    output adc_clk;
+    input ssp_dout;
+    output ssp_frame, ssp_din, ssp_clk;
+    input cross_hi, cross_lo;
+    output dbg;
+    input lo_is_125khz; // redundant signal, no longer used anywhere
+    input [7:0] divisor;
+
+reg [7:0] to_arm_shiftreg;
+reg [7:0] pck_divider;
+reg ant_lo;
+
+// this task runs on the rising egde of pck0 clock (24Mhz) and creates ant_lo
+// which is high for (divisor+1) pck0 cycles and low for the same duration
+// ant_lo is therefore a 50% duty cycle clock signal with a frequency of
+// 12Mhz/(divisor+1) which drives the antenna as well as the ADC clock adc_clk
+always @(posedge pck0)
+begin
+	if(pck_divider == divisor[7:0])
+		begin
+			pck_divider <= 8'd0;
+			ant_lo = !ant_lo;
+		end
+	else
+	begin
+		pck_divider <= pck_divider + 1;
+	end
+end
+
+// this task also runs at pck0 frequency (24Mhz) and is used to serialize
+// the ADC output which is then clocked into the ARM SSP.
+
+// because ant_lo always transitions when pck_divider = 0 we use the
+// pck_divider counter to sync our other signals off it
+// we read the ADC value when pck_divider=7 and shift it out on counts 8..15
+always @(posedge pck0)
+begin
+	if((pck_divider == 8'd7) && !ant_lo)
+        to_arm_shiftreg <= adc_d;
+    else
+	begin
+        to_arm_shiftreg[7:1] <= to_arm_shiftreg[6:0];
+		// simulation showed a glitch occuring due to the LSB of the shifter
+		// not being set as we shift bits out
+		// this ensures the ssp_din remains low after a transfer and suppresses
+		// the glitch that would occur when the last data shifted out ended in
+		// a 1 bit and the next data shifted out started with a 0 bit
+        to_arm_shiftreg[0] <= 1'b0;
+	end
+end
+
+// ADC samples on falling edge of adc_clk, data available on the rising edge
+
+// example of ssp transfer of binary value 1100101
+// start of transfer is indicated by the rise of the ssp_frame signal
+// ssp_din changes on the rising edge of the ssp_clk clock and is clocked into
+// the ARM by the falling edge of ssp_clk
+//             _______________________________
+// ssp_frame__|                               |__
+//             _______         ___     ___
+// ssp_din  __|       |_______|   |___|   |______
+//         _   _   _   _   _   _   _   _   _   _
+// ssp_clk  |_| |_| |_| |_| |_| |_| |_| |_| |_| |_
+
+// serialized SSP data is gated by ant_lo to suppress unwanted signal
+assign ssp_din = to_arm_shiftreg[7] && !ant_lo;
+// SSP clock always runs at 24Mhz
+assign ssp_clk = pck0;
+// SSP frame is gated by ant_lo and goes high when pck_divider=8..15
+assign ssp_frame = (pck_divider[7:3] == 5'd1) && !ant_lo;
+// unused signals tied low
+assign pwr_hi = 1'b0;
+assign pwr_oe1 = 1'b0;
+assign pwr_oe2 = 1'b0;
+assign pwr_oe3 = 1'b0;
+assign pwr_oe4 = 1'b0;
+// this is the antenna driver signal
+assign pwr_lo = ant_lo;
+// ADC clock out of phase with antenna driver
+assign adc_clk = ~ant_lo;
+// ADC clock also routed to debug pin
+assign dbg = adc_clk;
+endmodule