X-Git-Url: https://git.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/d19929cbe8d681b60496ca6d9d9cbd806822e163..cb366e9dbd0f421c143d6a9f02d7e0abc86c90ba:/fpga/lo_edge_detect.v?ds=sidebyside

diff --git a/fpga/lo_edge_detect.v b/fpga/lo_edge_detect.v
index 8458ee69..dc97fc6f 100644
--- a/fpga/lo_edge_detect.v
+++ b/fpga/lo_edge_detect.v
@@ -1,40 +1,38 @@
 //-----------------------------------------------------------------------------
-// The way that we connect things in low-frequency simulation mode. In this
-// case just pass everything through to the ARM, which can bit-bang this
-// (because it is so slow).
+// Copyright (C) 2014 iZsh <izsh at fail0verflow.com>
 //
-// Jonathan Westhues, April 2006
+// This code is licensed to you under the terms of the GNU GPL, version 2 or,
+// at your option, any later version. See the LICENSE.txt file for the text of
+// the license.
 //-----------------------------------------------------------------------------
+//
+// There are two modes:
+// - lf_ed_toggle_mode == 0: the output is set low (resp. high) when a low
+//   (resp. high) edge/peak is detected, with hysteresis
+// - lf_ed_toggle_mode == 1: the output is toggling whenever an edge/peak
+//   is detected.
+//   That way you can detect two consecutive edges/peaks at the same level (L/H)
+//
+// Output:
+// - ssp_frame (wired to TIOA1 on the arm) for the edge detection/state
+// - ssp_clk: cross_lo
+`include "lp20khz_1MSa_iir_filter.v"
+`include "lf_edge_detect.v"
 
 module lo_edge_detect(
-    pck0, ck_1356meg, ck_1356megb,
-    pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
-    adc_d, adc_clk,
-    ssp_frame, ssp_din, ssp_dout, ssp_clk,
-    cross_hi, cross_lo,
-    dbg,
-	  divisor,
-		lf_field
+    input pck0, input pck_divclk,
+    output pwr_lo, output pwr_hi,
+    output pwr_oe1, output pwr_oe2, output pwr_oe3, output pwr_oe4,
+    input [7:0] adc_d, output adc_clk,
+    output ssp_frame, input ssp_dout, output ssp_clk,
+    input cross_lo,
+    output dbg,
+    input lf_field,
+    input lf_ed_toggle_mode, input [7:0] lf_ed_threshold
 );
-    input pck0, ck_1356meg, ck_1356megb;
-    output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
-    input [7:0] adc_d;
-    output adc_clk;
-    input ssp_dout;
-    output ssp_frame, ssp_din, ssp_clk;
-    input cross_hi, cross_lo;
-    output dbg;
-	  input [7:0] divisor;
-		input lf_field;
-
-// Divide the clock to be used for the ADC
-reg [7:0] pck_divider;
-reg clk_state;
 
-wire tag_modulation; 
-assign tag_modulation = ssp_dout & !lf_field;
-wire reader_modulation; 
-assign reader_modulation = !ssp_dout & lf_field & clk_state;
+wire tag_modulation = ssp_dout & !lf_field;
+wire reader_modulation = !ssp_dout & lf_field & pck_divclk;
 
 // No logic, straight through.
 assign pwr_oe1 = 1'b0; // not used in LF mode
@@ -44,47 +42,25 @@ assign pwr_oe4 = tag_modulation;
 assign ssp_clk = cross_lo;
 assign pwr_lo = reader_modulation;
 assign pwr_hi = 1'b0;
-assign dbg = ssp_frame;
-
-always @(posedge pck0)
-begin
-	if(pck_divider == divisor[7:0])
-		begin
-			pck_divider <= 8'd0;
-			clk_state = !clk_state;
-		end
-	else
-	begin
-		pck_divider <= pck_divider + 1;
-	end
-end
-
-assign adc_clk = ~clk_state;
 
-// Toggle the output with hysteresis
-//  Set to high if the ADC value is above 200
-//  Set to low if the ADC value is below 64
-reg is_high;
-reg is_low;
-reg output_state;
+// filter the ADC values
+wire data_rdy;
+wire [7:0] adc_filtered;
+assign adc_clk = pck0;
+lp20khz_1MSa_iir_filter adc_filter(pck0, adc_d, data_rdy, adc_filtered);
 
-always @(posedge pck0)
-begin
-	if((pck_divider == 8'd7) && !clk_state) begin
-		is_high = (adc_d >= 8'd190);
-		is_low = (adc_d <= 8'd70);
-	end
-end
+// detect edges
+wire [7:0] high_threshold, highz_threshold, lowz_threshold, low_threshold;
+wire [7:0] max, min;
+wire edge_state, edge_toggle;
+lf_edge_detect lf_ed(pck0, adc_filtered, lf_ed_threshold,
+	max, min,
+	high_threshold, highz_threshold, lowz_threshold, low_threshold,
+	edge_state, edge_toggle);
 
-always @(posedge is_high or posedge is_low)
-begin
-	if(is_high)
-		output_state <= 1'd1;
-	else if(is_low)
-		output_state <= 1'd0;
-end
+assign dbg = lf_ed_toggle_mode ? edge_toggle : edge_state;
 
-assign ssp_frame = output_state;
+assign ssp_frame = lf_ed_toggle_mode ? edge_toggle : edge_state;
 
 endmodule