X-Git-Url: https://git.zerfleddert.de/cgi-bin/gitweb.cgi/proxmark3-svn/blobdiff_plain/db8296025f78251ffa2c28d6fe995bbb0a386c77..3458bb279b00048892e56cec6f0a13e8c03f97db:/armsrc/lfops.c

diff --git a/armsrc/lfops.c b/armsrc/lfops.c
index 3acecd6e..995a8810 100644
--- a/armsrc/lfops.c
+++ b/armsrc/lfops.c
@@ -4,7 +4,7 @@
 // the license.
 //-----------------------------------------------------------------------------
 // Miscellaneous routines for low frequency tag operations.
-// Tags supported here so far are Texas Instruments (TI), HID
+// Tags supported here so far are Texas Instruments (TI), HID, EM4x05, EM410x
 // Also routines for raw mode reading/simulating of LF waveform
 //-----------------------------------------------------------------------------
 
@@ -17,7 +17,8 @@
 #include "lfdemod.h"
 #include "lfsampling.h"
 #include "protocols.h"
-#include "usb_cdc.h" //test
+#include "usb_cdc.h"
+#include "fpgaloader.h"
 
 /**
  * Function to do a modulation and then get samples.
@@ -28,52 +29,104 @@
  */
 void ModThenAcquireRawAdcSamples125k(uint32_t delay_off, uint32_t period_0, uint32_t period_1, uint8_t *command)
 {
+	// start timer
+	StartTicks();
 
-	int divisor_used = 95; // 125 KHz
-	// see if 'h' was specified
+	// use lf config settings
+	sample_config *sc = getSamplingConfig();
 
-	if (command[strlen((char *) command) - 1] == 'h')
-		divisor_used = 88; // 134.8 KHz
-
-	sample_config sc = { 0,0,1, divisor_used, 0};
-	setSamplingConfig(&sc);
-
-	/* Make sure the tag is reset */
+	// Make sure the tag is reset
 	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	SpinDelay(2500);
+	WaitMS(2500);
 
-	LFSetupFPGAForADC(sc.divisor, 1);
+	// clear read buffer (after fpga bitstream loaded...)
+	BigBuf_Clear_keep_EM();
 
-	// And a little more time for the tag to fully power up
-	SpinDelay(2000);
+	// power on
+	LFSetupFPGAForADC(sc->divisor, 1);
 
+	// And a little more time for the tag to fully power up
+	WaitMS(2000);
+	// if delay_off = 0 then just bitbang 1 = antenna on 0 = off for respective periods.
+	bool bitbang = delay_off == 0;
 	// now modulate the reader field
-	while(*command != '\0' && *command != ' ') {
+
+	if (bitbang) {
+		// HACK it appears the loop and if statements take up about 7us so adjust waits accordingly...
+		uint8_t hack_cnt = 7;
+		if (period_0 < hack_cnt || period_1 < hack_cnt) {
+			DbpString("Warning periods cannot be less than 7us in bit bang mode");
+			FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
+			LED_D_OFF();
+			return;
+		}
+
+		// hack2 needed---  it appears to take about 8-16us to turn the antenna back on 
+		// leading to ~ 1 to 2 125khz samples extra in every off period 
+		// so we should test for last 0 before next 1 and reduce period_0 by this extra amount...
+		// but is this time different for every antenna or other hw builds???  more testing needed
+
+		// prime cmd_len to save time comparing strings while modulating
+		int cmd_len = 0;
+		while(command[cmd_len] != '\0' && command[cmd_len] != ' ')
+			cmd_len++;
+
+		int counter = 0;
+		bool off = false;
+		for (counter = 0; counter < cmd_len; counter++) {
+			// if cmd = 0 then turn field off
+			if (command[counter] == '0') {
+				// if field already off leave alone (affects timing otherwise)
+				if (off == false) {
+					FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
+					LED_D_OFF();
+					off = true;
+				}
+				// note we appear to take about 7us to switch over (or run the if statements/loop...)
+				WaitUS(period_0-hack_cnt);
+			// else if cmd = 1 then turn field on
+			} else {
+				// if field already on leave alone (affects timing otherwise)
+				if (off) {
+					FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
+					LED_D_ON();
+					off = false;
+				}
+				// note we appear to take about 7us to switch over (or run the if statements/loop...)
+				WaitUS(period_1-hack_cnt);
+			}
+		}
+	} else { // old mode of cmd read using delay as off period
+		while(*command != '\0' && *command != ' ') {
+			FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
+			LED_D_OFF();
+			WaitUS(delay_off);
+			FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc->divisor);
+			FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
+			LED_D_ON();
+			if(*(command++) == '0') {
+				WaitUS(period_0);
+			} else {
+				WaitUS(period_1);
+			}
+		}
 		FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
 		LED_D_OFF();
-		SpinDelayUs(delay_off);
-		FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc.divisor);
-
-		FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
-		LED_D_ON();
-		if(*(command++) == '0')
-			SpinDelayUs(period_0);
-		else
-			SpinDelayUs(period_1);
+		WaitUS(delay_off);
+		FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc->divisor);
 	}
-	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	LED_D_OFF();
-	SpinDelayUs(delay_off);
-	FpgaSendCommand(FPGA_CMD_SET_DIVISOR, sc.divisor);
 
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
 
 	// now do the read
-	DoAcquisition_config(false);
-}
-
+	DoAcquisition_config(false, 0);
 
+	// Turn off antenna
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
+	// tell client we are done
+	cmd_send(CMD_ACK,0,0,0,0,0);
+}
 
 /* blank r/w tag data stream
 ...0000000000000000 01111111
@@ -214,8 +267,6 @@ void ReadTItag(void)
 	}
 }
 
-
-
 void WriteTIbyte(uint8_t b)
 {
 	int i = 0;
@@ -250,7 +301,7 @@ void AcquireTiType(void)
 
 	// clear buffer
 	uint32_t *BigBuf = (uint32_t *)BigBuf_get_addr();
-	memset(BigBuf,0,BigBuf_max_traceLen()/sizeof(uint32_t));
+	BigBuf_Clear_ext(false);
 
 	// Set up the synchronous serial port
 	AT91C_BASE_PIOA->PIO_PDR = GPIO_SSC_DIN;
@@ -312,16 +363,11 @@ void AcquireTiType(void)
 	}
 }
 
-
-
-
 // arguments: 64bit data split into 32bit idhi:idlo and optional 16bit crc
 // if crc provided, it will be written with the data verbatim (even if bogus)
 // if not provided a valid crc will be computed from the data and written.
 void WriteTItag(uint32_t idhi, uint32_t idlo, uint16_t crc)
 {
-
-
 	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
 	if(crc == 0) {
 		crc = update_crc16(crc, (idlo)&0xff);
@@ -386,7 +432,7 @@ void WriteTItag(uint32_t idhi, uint32_t idlo, uint16_t crc)
 	AcquireTiType();
 
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	DbpString("Now use tiread to check");
+	DbpString("Now use `lf ti read` to check");
 }
 
 void SimulateTagLowFrequency(int period, int gap, int ledcontrol)
@@ -394,7 +440,8 @@ void SimulateTagLowFrequency(int period, int gap, int ledcontrol)
 	int i;
 	uint8_t *tab = BigBuf_get_addr();
 
-	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
+	//note FpgaDownloadAndGo destroys the bigbuf so be sure this is called before now...
+	//FpgaDownloadAndGo(FPGA_BITSTREAM_LF);  
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_EDGE_DETECT);
 
 	AT91C_BASE_PIOA->PIO_PER = GPIO_SSC_DOUT | GPIO_SSC_CLK;
@@ -402,18 +449,25 @@ void SimulateTagLowFrequency(int period, int gap, int ledcontrol)
 	AT91C_BASE_PIOA->PIO_OER = GPIO_SSC_DOUT;
 	AT91C_BASE_PIOA->PIO_ODR = GPIO_SSC_CLK;
 
- #define SHORT_COIL()	LOW(GPIO_SSC_DOUT)
- #define OPEN_COIL()		HIGH(GPIO_SSC_DOUT)
+ #define SHORT_COIL()   LOW(GPIO_SSC_DOUT)
+ #define OPEN_COIL()    HIGH(GPIO_SSC_DOUT)
 
 	i = 0;
 	for(;;) {
 		//wait until SSC_CLK goes HIGH
+		int ii = 0;
 		while(!(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK)) {
-			if(BUTTON_PRESS() || (usb_poll_validate_length() )) {
-				DbpString("Stopped");
-				return;
+			//only check every 1000th time (usb_poll_validate_length on some systems was too slow)
+			if ( ii == 1000 ) {
+				if (BUTTON_PRESS() || usb_poll_validate_length() ) {
+					FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
+					DbpString("Stopped");
+					return;
+				}
+				ii=0;
 			}
 			WDT_HIT();
+			ii++;
 		}
 		if (ledcontrol)
 			LED_D_ON();
@@ -425,13 +479,20 @@ void SimulateTagLowFrequency(int period, int gap, int ledcontrol)
 
 		if (ledcontrol)
 			LED_D_OFF();
+		ii=0;
 		//wait until SSC_CLK goes LOW
 		while(AT91C_BASE_PIOA->PIO_PDSR & GPIO_SSC_CLK) {
-			if(BUTTON_PRESS()) {
-				DbpString("Stopped");
-				return;
+			//only check every 1000th time (usb_poll_validate_length on some systems was too slow)
+			if ( ii == 1000 ) { 
+				if (BUTTON_PRESS() || usb_poll_validate_length() ) {
+					FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
+					DbpString("Stopped");
+					return;
+				}
+				ii=0;
 			}
 			WDT_HIT();
+			ii++;
 		}
 
 		i++;
@@ -443,6 +504,7 @@ void SimulateTagLowFrequency(int period, int gap, int ledcontrol)
 				SpinDelayUs(gap);
 			}
 		}
+
 	}
 }
 
@@ -507,7 +569,7 @@ static void fcAll(uint8_t fc, int *n, uint8_t clock, uint16_t *modCnt)
 	uint8_t wavesPerClock = clock/fc;
 	uint8_t mod = clock % fc;    //modifier
 	uint8_t modAdj = fc/mod;     //how often to apply modifier
-	bool modAdjOk = !(fc % mod); //if (fc % mod==0) modAdjOk=TRUE;
+	bool modAdjOk = !(fc % mod); //if (fc % mod==0) modAdjOk=true;
 	// loop through clock - step field clock
 	for (uint8_t idx=0; idx < wavesPerClock; idx++){
 		// put 1/2 FC length 1's and 1/2 0's per field clock wave (to create the wave)
@@ -532,7 +594,7 @@ static void fcAll(uint8_t fc, int *n, uint8_t clock, uint16_t *modCnt)
 
 // prepare a waveform pattern in the buffer based on the ID given then
 // simulate a HID tag until the button is pressed
-void CmdHIDsimTAG(int hi, int lo, int ledcontrol)
+void CmdHIDsimTAG(int hi2, int hi, int lo, int ledcontrol)
 {
 	int n=0, i=0;
 	/*
@@ -545,10 +607,13 @@ void CmdHIDsimTAG(int hi, int lo, int ledcontrol)
 	 nor 1 bits, they are special patterns (a = set of 12 fc8 and b = set of 10 fc10)
 	*/
 
-	if (hi>0xFFF) {
-		DbpString("Tags can only have 44 bits. - USE lf simfsk for larger tags");
+	if (hi2>0x0FFFFFFF) {
+		DbpString("Tags can only have 44 or 84 bits. - USE lf simfsk for larger tags");
 		return;
 	}
+	// set LF so we don't kill the bigbuf we are setting with simulation data.
+	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
+
 	fc(0,&n);
 	// special start of frame marker containing invalid bit sequences
 	fc(8,  &n);	fc(8,  &n); // invalid
@@ -557,13 +622,35 @@ void CmdHIDsimTAG(int hi, int lo, int ledcontrol)
 	fc(8,  &n);	fc(10, &n); // logical 0
 
 	WDT_HIT();
-	// manchester encode bits 43 to 32
-	for (i=11; i>=0; i--) {
-		if ((i%4)==3) fc(0,&n);
-		if ((hi>>i)&1) {
-			fc(10, &n); fc(8,  &n);		// low-high transition
-		} else {
-			fc(8,  &n); fc(10, &n);		// high-low transition
+	if (hi2 > 0 || hi > 0xFFF){
+		// manchester encode bits 91 to 64 (91-84 are part of the header)
+		for (i=27; i>=0; i--) {
+			if ((i%4)==3) fc(0,&n);
+			if ((hi2>>i)&1) {
+				fc(10, &n); fc(8,  &n);		// low-high transition
+			} else {
+				fc(8,  &n); fc(10, &n);		// high-low transition
+			}
+		}
+		WDT_HIT();
+		// manchester encode bits 63 to 32
+		for (i=31; i>=0; i--) {
+			if ((i%4)==3) fc(0,&n);
+			if ((hi>>i)&1) {
+				fc(10, &n); fc(8,  &n);		// low-high transition
+			} else {
+				fc(8,  &n); fc(10, &n);		// high-low transition
+			}
+		}
+	} else {
+		// manchester encode bits 43 to 32
+		for (i=11; i>=0; i--) {
+			if ((i%4)==3) fc(0,&n);
+			if ((hi>>i)&1) {
+				fc(10, &n); fc(8,  &n);		// low-high transition
+			} else {
+				fc(8,  &n); fc(10, &n);		// high-low transition
+			}
 		}
 	}
 
@@ -599,6 +686,9 @@ void CmdFSKsimTAG(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream)
 	uint8_t clk = arg2 & 0xFF;
 	uint8_t invert = (arg2 >> 8) & 1;
 
+	// set LF so we don't kill the bigbuf we are setting with simulation data.
+	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
+
 	for (i=0; i<size; i++){
 		if (BitStream[i] == invert){
 			fcAll(fcLow, &n, clk, &modCnt);
@@ -649,6 +739,19 @@ static void biphaseSimBit(uint8_t c, int *n, uint8_t clock, uint8_t *phase)
 		memset(dest+(*n), c ^ *phase, clock);
 		*phase ^= 1;
 	}
+	*n += clock;
+}
+
+static void stAskSimBit(int *n, uint8_t clock) {
+	uint8_t *dest = BigBuf_get_addr();
+	uint8_t halfClk = clock/2;
+	//ST = .5 high .5 low 1.5 high .5 low 1 high	
+	memset(dest+(*n), 1, halfClk);
+	memset(dest+(*n) + halfClk, 0, halfClk);
+	memset(dest+(*n) + clock, 1, clock + halfClk);
+	memset(dest+(*n) + clock*2 + halfClk, 0, halfClk);
+	memset(dest+(*n) + clock*3, 1, clock);
+	*n += clock*4;
 }
 
 // args clock, ask/man or askraw, invert, transmission separator
@@ -661,12 +764,15 @@ void CmdASKsimTag(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream)
 	uint8_t separator = arg2 & 1;
 	uint8_t invert = (arg2 >> 8) & 1;
 
+	// set LF so we don't kill the bigbuf we are setting with simulation data.
+	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
+
 	if (encoding==2){  //biphase
 		uint8_t phase=0;
 		for (i=0; i<size; i++){
 			biphaseSimBit(BitStream[i]^invert, &n, clk, &phase);
 		}
-		if (BitStream[0]==BitStream[size-1]){ //run a second set inverted to keep phase in check
+		if (phase==1) { //run a second set inverted to keep phase in check
 			for (i=0; i<size; i++){
 				biphaseSimBit(BitStream[i]^invert, &n, clk, &phase);
 			}
@@ -675,14 +781,16 @@ void CmdASKsimTag(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream)
 		for (i=0; i<size; i++){
 			askSimBit(BitStream[i]^invert, &n, clk, encoding);
 		}
-		if (encoding==0 && BitStream[0]==BitStream[size-1]){ //run a second set inverted (for biphase phase)
+		if (encoding==0 && BitStream[0]==BitStream[size-1]){ //run a second set inverted (for ask/raw || biphase phase)
 			for (i=0; i<size; i++){
 				askSimBit(BitStream[i]^invert^1, &n, clk, encoding);
 			}
 		}
 	}
-	
-	if (separator==1) Dbprintf("sorry but separator option not yet available"); 
+	if (separator==1 && encoding == 1)
+		stAskSimBit(&n, clk);
+	else if (separator==1)
+		Dbprintf("sorry but separator option not yet available");
 
 	Dbprintf("Simulating with clk: %d, invert: %d, encoding: %d, separator: %d, n: %d",clk, invert, encoding, separator, n);
 	//DEBUG
@@ -692,14 +800,10 @@ void CmdASKsimTag(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream)
 	//Dbprintf("%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d", dest[i],dest[i+1],dest[i+2],dest[i+3],dest[i+4],dest[i+5],dest[i+6],dest[i+7],dest[i+8],dest[i+9],dest[i+10],dest[i+11],dest[i+12],dest[i+13],dest[i+14],dest[i+15]);
 	//i+=16;
 	//Dbprintf("%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d", dest[i],dest[i+1],dest[i+2],dest[i+3],dest[i+4],dest[i+5],dest[i+6],dest[i+7],dest[i+8],dest[i+9],dest[i+10],dest[i+11],dest[i+12],dest[i+13],dest[i+14],dest[i+15]);
-
-	if (ledcontrol)
-		LED_A_ON();
 	
+	if (ledcontrol) LED_A_ON();
 	SimulateTagLowFrequency(n, 0, ledcontrol);
-
-	if (ledcontrol)
-		LED_A_OFF();
+	if (ledcontrol) LED_A_OFF();
 }
 
 //carrier can be 2,4 or 8
@@ -734,11 +838,14 @@ void CmdPSKsimTag(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream)
 	uint8_t carrier = arg1 & 0xFF;
 	uint8_t invert = arg2 & 0xFF;
 	uint8_t curPhase = 0;
+	// set LF so we don't kill the bigbuf we are setting with simulation data.
+	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
+
 	for (i=0; i<size; i++){
 		if (BitStream[i] == curPhase){
-			pskSimBit(carrier, &n, clk, &curPhase, FALSE);
+			pskSimBit(carrier, &n, clk, &curPhase, false);
 		} else {
-			pskSimBit(carrier, &n, clk, &curPhase, TRUE);
+			pskSimBit(carrier, &n, clk, &curPhase, true);
 		}
 	}
 	Dbprintf("Simulating with Carrier: %d, clk: %d, invert: %d, n: %d",carrier, clk, invert, n);
@@ -749,27 +856,27 @@ void CmdPSKsimTag(uint16_t arg1, uint16_t arg2, size_t size, uint8_t *BitStream)
 	//i+=16;
 	//Dbprintf("%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d%d", dest[i],dest[i+1],dest[i+2],dest[i+3],dest[i+4],dest[i+5],dest[i+6],dest[i+7],dest[i+8],dest[i+9],dest[i+10],dest[i+11],dest[i+12],dest[i+13],dest[i+14],dest[i+15]);
 		   
-	if (ledcontrol)
-		LED_A_ON();
+	if (ledcontrol) LED_A_ON();
 	SimulateTagLowFrequency(n, 0, ledcontrol);
-
-	if (ledcontrol)
-		LED_A_OFF();
+	if (ledcontrol) LED_A_OFF();
 }
 
 // loop to get raw HID waveform then FSK demodulate the TAG ID from it
-void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol)
+void CmdHIDdemodFSK(int findone, int *high2, int *high, int *low, int ledcontrol)
 {
 	uint8_t *dest = BigBuf_get_addr();
 	//const size_t sizeOfBigBuff = BigBuf_max_traceLen();
 	size_t size; 
 	uint32_t hi2=0, hi=0, lo=0;
 	int idx=0;
+	int dummyIdx = 0;
 	// Configure to go in 125Khz listen mode
 	LFSetupFPGAForADC(95, true);
 
-	while(!BUTTON_PRESS() && !usb_poll_validate_length()) {
+	//clear read buffer
+	BigBuf_Clear_keep_EM();
 
+	while(!BUTTON_PRESS() && !usb_poll_validate_length()) {
 		WDT_HIT();
 		if (ledcontrol) LED_A_ON();
 
@@ -777,72 +884,84 @@ void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol)
 		// FSK demodulator
 		//size = sizeOfBigBuff;  //variable size will change after demod so re initialize it before use
 		size = 50*128*2; //big enough to catch 2 sequences of largest format
-		idx = HIDdemodFSK(dest, &size, &hi2, &hi, &lo);
+		idx = HIDdemodFSK(dest, &size, &hi2, &hi, &lo, &dummyIdx);
 		
 		if (idx>0 && lo>0 && (size==96 || size==192)){
+			uint8_t bitlen = 0;
+			uint32_t fc = 0;
+			uint32_t cardnum = 0;
+			bool decoded = false;
+
 			// go over previously decoded manchester data and decode into usable tag ID
-			if (hi2 != 0){ //extra large HID tags  88/192 bits
-				Dbprintf("TAG ID: %x%08x%08x (%d)",
-				  (unsigned int) hi2, (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF);
-			}else {  //standard HID tags 44/96 bits
-				//Dbprintf("TAG ID: %x%08x (%d)",(unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF); //old print cmd
-				uint8_t bitlen = 0;
-				uint32_t fc = 0;
-				uint32_t cardnum = 0;
-				if (((hi>>5)&1) == 1){//if bit 38 is set then < 37 bit format is used
-					uint32_t lo2=0;
-					lo2=(((hi & 31) << 12) | (lo>>20)); //get bits 21-37 to check for format len bit
-					uint8_t idx3 = 1;
-					while(lo2 > 1){ //find last bit set to 1 (format len bit)
-						lo2=lo2 >> 1;
-						idx3++;
-					}
-					bitlen = idx3+19;
-					fc =0;
-					cardnum=0;
-					if(bitlen == 26){
-						cardnum = (lo>>1)&0xFFFF;
-						fc = (lo>>17)&0xFF;
-					}
-					if(bitlen == 37){
-						cardnum = (lo>>1)&0x7FFFF;
-						fc = ((hi&0xF)<<12)|(lo>>20);
-					}
-					if(bitlen == 34){
-						cardnum = (lo>>1)&0xFFFF;
-						fc= ((hi&1)<<15)|(lo>>17);
-					}
-					if(bitlen == 35){
-						cardnum = (lo>>1)&0xFFFFF;
-						fc = ((hi&1)<<11)|(lo>>21);
-					}
+			if ((hi2 & 0x000FFFF) != 0){ //extra large HID tags  88/192 bits
+				uint32_t bp = hi2 & 0x000FFFFF;
+				bitlen = 63;
+				while (bp > 0) {
+					bp = bp >> 1;
+					bitlen++;
 				}
-				else { //if bit 38 is not set then 37 bit format is used
-					bitlen= 37;
-					fc =0;
-					cardnum=0;
-					if(bitlen==37){
-						cardnum = (lo>>1)&0x7FFFF;
-						fc = ((hi&0xF)<<12)|(lo>>20);
-					}
+			} else if ((hi >> 6) > 0) {
+				uint32_t bp = hi;
+				bitlen = 31;
+				while (bp > 0) {
+					bp = bp >> 1;
+					bitlen++;
 				}
-				//Dbprintf("TAG ID: %x%08x (%d)",
-				// (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF);
-				Dbprintf("TAG ID: %x%08x (%d) - Format Len: %dbit - FC: %d - Card: %d",
-						 (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF,
-						 (unsigned int) bitlen, (unsigned int) fc, (unsigned int) cardnum);
+			} else if (((hi >> 5) & 1) == 0) {
+				bitlen = 37;
+			} else if ((hi & 0x0000001F) > 0 ) {
+				uint32_t bp = (hi & 0x0000001F);
+				bitlen = 31;
+				while (bp > 0) {
+					bp = bp >> 1;
+					bitlen++;
+				}
+			} else {
+				uint32_t bp = lo;
+				bitlen = 0;
+				while (bp > 0) {
+					bp = bp >> 1;
+					bitlen++;
+				}
+			}
+			switch (bitlen){
+				case 26:
+					cardnum = (lo>>1)&0xFFFF;
+					fc = (lo>>17)&0xFF;
+					decoded = true;
+					break;
+				case 35:
+					cardnum = (lo>>1)&0xFFFFF;
+					fc = ((hi&1)<<11)|(lo>>21);
+					decoded = true;
+					break;
 			}
+				
+			if (hi2 != 0) //extra large HID tags  88/192 bits
+				Dbprintf("TAG ID: %x%08x%08x (%d)",
+					(unsigned int) hi2, (unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF);
+			else 
+				Dbprintf("TAG ID: %x%08x (%d)",
+					(unsigned int) hi, (unsigned int) lo, (unsigned int) (lo>>1) & 0xFFFF);
+			
+			if (decoded)
+				Dbprintf("Format Len: %dbits - FC: %d - Card: %d",
+					(unsigned int) bitlen, (unsigned int) fc, (unsigned int) cardnum);
+
 			if (findone){
 				if (ledcontrol)	LED_A_OFF();
+				*high2 = hi2;
 				*high = hi;
 				*low = lo;
-				return;
+				break;
 			}
 			// reset
 		}
 		hi2 = hi = lo = idx = 0;
 		WDT_HIT();
 	}
+
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
 	DbpString("Stopped");
 	if (ledcontrol) LED_A_OFF();
 }
@@ -851,9 +970,10 @@ void CmdHIDdemodFSK(int findone, int *high, int *low, int ledcontrol)
 void CmdAWIDdemodFSK(int findone, int *high, int *low, int ledcontrol)
 {
 	uint8_t *dest = BigBuf_get_addr();
-	//const size_t sizeOfBigBuff = BigBuf_max_traceLen();
 	size_t size; 
-	int idx=0;
+	int idx=0, dummyIdx=0;
+	//clear read buffer
+	BigBuf_Clear_keep_EM();
 	// Configure to go in 125Khz listen mode
 	LFSetupFPGAForADC(95, true);
 
@@ -864,75 +984,75 @@ void CmdAWIDdemodFSK(int findone, int *high, int *low, int ledcontrol)
 
 		DoAcquisition_default(-1,true);
 		// FSK demodulator
-		//size = sizeOfBigBuff;  //variable size will change after demod so re initialize it before use
 		size = 50*128*2; //big enough to catch 2 sequences of largest format
-		idx = AWIDdemodFSK(dest, &size);
+		idx = AWIDdemodFSK(dest, &size, &dummyIdx);
 		
-		if (idx>0 && size==96){
-	        // Index map
-	        // 0            10            20            30              40            50              60
-	        // |            |             |             |               |             |               |
-	        // 01234567 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 - to 96
-	        // -----------------------------------------------------------------------------
-	        // 00000001 000 1 110 1 101 1 011 1 101 1 010 0 000 1 000 1 010 0 001 0 110 1 100 0 000 1 000 1
-	        // premable bbb o bbb o bbw o fff o fff o ffc o ccc o ccc o ccc o ccc o ccc o wxx o xxx o xxx o - to 96
-	        //          |---26 bit---|    |-----117----||-------------142-------------|
-	        // b = format bit len, o = odd parity of last 3 bits
-	        // f = facility code, c = card number
-	        // w = wiegand parity
-	        // (26 bit format shown)
-
-	        //get raw ID before removing parities
-	        uint32_t rawLo = bytebits_to_byte(dest+idx+64,32);
-	        uint32_t rawHi = bytebits_to_byte(dest+idx+32,32);
-	        uint32_t rawHi2 = bytebits_to_byte(dest+idx,32);
-
-	        size = removeParity(dest, idx+8, 4, 1, 88);
-	        // ok valid card found!
-
-	        // Index map
-	        // 0           10         20        30          40        50        60
-	        // |           |          |         |           |         |         |
-	        // 01234567 8 90123456 7890123456789012 3 456789012345678901234567890123456
-	        // -----------------------------------------------------------------------------
-	        // 00011010 1 01110101 0000000010001110 1 000000000000000000000000000000000
-	        // bbbbbbbb w ffffffff cccccccccccccccc w xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
-	        // |26 bit|   |-117--| |-----142------|
-	        // b = format bit len, o = odd parity of last 3 bits
-	        // f = facility code, c = card number
-	        // w = wiegand parity
-	        // (26 bit format shown)
-
-	        uint32_t fc = 0;
-	        uint32_t cardnum = 0;
-	        uint32_t code1 = 0;
-	        uint32_t code2 = 0;
-	        uint8_t fmtLen = bytebits_to_byte(dest,8);
-	        if (fmtLen==26){
-	                fc = bytebits_to_byte(dest+9, 8);
-	                cardnum = bytebits_to_byte(dest+17, 16);
-	                code1 = bytebits_to_byte(dest+8,fmtLen);
-	                Dbprintf("AWID Found - BitLength: %d, FC: %d, Card: %d - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, fc, cardnum, code1, rawHi2, rawHi, rawLo);
-	        } else {
-	                cardnum = bytebits_to_byte(dest+8+(fmtLen-17), 16);
-	                if (fmtLen>32){
-                        code1 = bytebits_to_byte(dest+8,fmtLen-32);
-                        code2 = bytebits_to_byte(dest+8+(fmtLen-32),32);
-                        Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%d) - Wiegand: %x%08x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, code2, rawHi2, rawHi, rawLo);
-                } else{
-                        code1 = bytebits_to_byte(dest+8,fmtLen);
-                        Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%d) - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, rawHi2, rawHi, rawLo);
-                }
-			}
-			if (findone){
-				if (ledcontrol)	LED_A_OFF();
-				return;
+		if (idx<=0 || size!=96) continue;
+		// Index map
+		// 0            10            20            30              40            50              60
+		// |            |             |             |               |             |               |
+		// 01234567 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 456 7 890 1 234 5 678 9 012 3 - to 96
+		// -----------------------------------------------------------------------------
+		// 00000001 000 1 110 1 101 1 011 1 101 1 010 0 000 1 000 1 010 0 001 0 110 1 100 0 000 1 000 1
+		// premable bbb o bbb o bbw o fff o fff o ffc o ccc o ccc o ccc o ccc o ccc o wxx o xxx o xxx o - to 96
+		//          |---26 bit---|    |-----117----||-------------142-------------|
+		// b = format bit len, o = odd parity of last 3 bits
+		// f = facility code, c = card number
+		// w = wiegand parity
+		// (26 bit format shown)
+
+		//get raw ID before removing parities
+		uint32_t rawLo = bytebits_to_byte(dest+idx+64,32);
+		uint32_t rawHi = bytebits_to_byte(dest+idx+32,32);
+		uint32_t rawHi2 = bytebits_to_byte(dest+idx,32);
+
+		size = removeParity(dest, idx+8, 4, 1, 88);
+		if (size != 66) continue;
+		// ok valid card found!
+
+		// Index map
+		// 0           10         20        30          40        50        60
+		// |           |          |         |           |         |         |
+		// 01234567 8 90123456 7890123456789012 3 456789012345678901234567890123456
+		// -----------------------------------------------------------------------------
+		// 00011010 1 01110101 0000000010001110 1 000000000000000000000000000000000
+		// bbbbbbbb w ffffffff cccccccccccccccc w xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
+		// |26 bit|   |-117--| |-----142------|
+		// b = format bit len, o = odd parity of last 3 bits
+		// f = facility code, c = card number
+		// w = wiegand parity
+		// (26 bit format shown)
+
+		uint32_t fc = 0;
+		uint32_t cardnum = 0;
+		uint32_t code1 = 0;
+		uint32_t code2 = 0;
+		uint8_t fmtLen = bytebits_to_byte(dest,8);
+		if (fmtLen==26){
+			fc = bytebits_to_byte(dest+9, 8);
+			cardnum = bytebits_to_byte(dest+17, 16);
+			code1 = bytebits_to_byte(dest+8,fmtLen);
+			Dbprintf("AWID Found - BitLength: %d, FC: %d, Card: %d - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, fc, cardnum, code1, rawHi2, rawHi, rawLo);
+		} else {
+			cardnum = bytebits_to_byte(dest+8+(fmtLen-17), 16);
+			if (fmtLen>32){
+				code1 = bytebits_to_byte(dest+8,fmtLen-32);
+				code2 = bytebits_to_byte(dest+8+(fmtLen-32),32);
+				Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%d) - Wiegand: %x%08x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, code2, rawHi2, rawHi, rawLo);
+			} else{
+				code1 = bytebits_to_byte(dest+8,fmtLen);
+				Dbprintf("AWID Found - BitLength: %d -unknown BitLength- (%d) - Wiegand: %x, Raw: %08x%08x%08x", fmtLen, cardnum, code1, rawHi2, rawHi, rawLo);
 			}
-			// reset
 		}
+		if (findone){
+			if (ledcontrol)	LED_A_OFF();
+			break;
+		}
+		// reset
 		idx = 0;
 		WDT_HIT();
 	}
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
 	DbpString("Stopped");
 	if (ledcontrol) LED_A_OFF();
 }
@@ -945,6 +1065,8 @@ void CmdEM410xdemod(int findone, int *high, int *low, int ledcontrol)
 	int clk=0, invert=0, errCnt=0, maxErr=20;
 	uint32_t hi=0;
 	uint64_t lo=0;
+	//clear read buffer
+	BigBuf_Clear_keep_EM();
 	// Configure to go in 125Khz listen mode
 	LFSetupFPGAForADC(95, true);
 
@@ -985,13 +1107,14 @@ void CmdEM410xdemod(int findone, int *high, int *low, int ledcontrol)
 				if (ledcontrol) LED_A_OFF();
 				*high=lo>>32;
 				*low=lo & 0xFFFFFFFF;
-				return;
+				break;
 			}
 		}
 		WDT_HIT();
 		hi = lo = size = idx = 0;
 		clk = invert = errCnt = 0;
 	}
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
 	DbpString("Stopped");
 	if (ledcontrol) LED_A_OFF();
 }
@@ -1004,6 +1127,9 @@ void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol)
 	uint8_t version=0;
 	uint8_t facilitycode=0;
 	uint16_t number=0;
+	int dummyIdx=0;
+	//clear read buffer
+	BigBuf_Clear_keep_EM();
 	// Configure to go in 125Khz listen mode
 	LFSetupFPGAForADC(95, true);
 
@@ -1013,7 +1139,7 @@ void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol)
 		DoAcquisition_default(-1,true);
 		//fskdemod and get start index
 		WDT_HIT();
-		idx = IOdemodFSK(dest, BigBuf_max_traceLen());
+		idx = IOdemodFSK(dest, BigBuf_max_traceLen(), &dummyIdx);
 		if (idx<0) continue;
 		//valid tag found
 
@@ -1048,7 +1174,7 @@ void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol)
 			//LED_A_OFF();
 			*high=code;
 			*low=code2;
-			return;
+			break;
 		}
 		code=code2=0;
 		version=facilitycode=0;
@@ -1057,6 +1183,7 @@ void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol)
 
 		WDT_HIT();
 	}
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
 	DbpString("Stopped");
 	if (ledcontrol) LED_A_OFF();
 }
@@ -1064,60 +1191,269 @@ void CmdIOdemodFSK(int findone, int *high, int *low, int ledcontrol)
 /*------------------------------
  * T5555/T5557/T5567/T5577 routines
  *------------------------------
- */
-
-/* NOTE: T55x7/T5555 configuration register definitions moved to protocols.h */
-
-/*
+ * NOTE: T55x7/T5555 configuration register definitions moved to protocols.h
+ *
  * Relevant communication times in microsecond
  * To compensate antenna falling times shorten the write times
  * and enlarge the gap ones.
  * Q5 tags seems to have issues when these values changes. 
  */
+
+ /*
+ // Original Timings for reference
+//note startgap must be sent after tag has been powered up for more than 3ms (per T5557 ds)
+ 
 #define START_GAP 31*8 // was 250 // SPEC:  1*8 to 50*8 - typ 15*8 (or 15fc)
 #define WRITE_GAP 20*8 // was 160 // SPEC:  1*8 to 20*8 - typ 10*8 (or 10fc)
 #define WRITE_0   18*8 // was 144 // SPEC: 16*8 to 32*8 - typ 24*8 (or 24fc)
 #define WRITE_1   50*8 // was 400 // SPEC: 48*8 to 64*8 - typ 56*8 (or 56fc)  432 for T55x7; 448 for E5550
-#define READ_GAP  26*8 
+#define READ_GAP  15*8 
+
+*/
+/* Q5 timing datasheet:
+ * Type                  |  MIN   | Typical |  Max   |
+ * Start_Gap             |  10*8  |    ?    |  50*8  |
+ * Write_Gap Normal mode |   8*8  |   14*8  |  20*8  | 
+ * Write_Gap Fast Mode   |   8*8  |    ?    |  20*8  |
+ * Write_0   Normal mode |  16*8  |   24*8  |  32*8  |
+ * Write_1   Normal mode |  48*8  |   56*8  |  64*8  |
+ * Write_0   Fast Mode   |   8*8  |   12*8  |  16*8  |
+ * Write_1   Fast Mode   |  24*8  |   28*8  |  32*8  |
+*/
+
+/* T5557 timing datasheet:
+ * Type                  |  MIN   | Typical |  Max   |
+ * Start_Gap             |  10*8  |    ?    |  50*8  |
+ * Write_Gap Normal mode |   8*8  |50-150us |  30*8  | 
+ * Write_Gap Fast Mode   |   8*8  |    ?    |  20*8  |
+ * Write_0   Normal mode |  16*8  |   24*8  |  31*8  | 
+ * Write_1   Normal mode |  48*8  |   54*8  |  63*8  | 
+ * Write_0   Fast Mode   |   8*8  |   12*8  |  15*8  |
+ * Write_1   Fast Mode   |  24*8  |   28*8  |  31*8  |
+*/
+
+/* T5577C timing datasheet for Fixed-Bit-Length protocol (defualt):
+ * Type                  |  MIN   | Typical |  Max   |
+ * Start_Gap             |   8*8  |   15*8  |  50*8  |
+ * Write_Gap Normal mode |   8*8  |   10*8  |  20*8  | 
+ * Write_Gap Fast Mode   |   8*8  |   10*8  |  20*8  |
+ * Write_0   Normal mode |  16*8  |   24*8  |  32*8  | 
+ * Write_1   Normal mode |  48*8  |   56*8  |  64*8  | 
+ * Write_0   Fast Mode   |   8*8  |   12*8  |  16*8  |
+ * Write_1   Fast Mode   |  24*8  |   28*8  |  32*8  |
+*/
+
+// Structure to hold Timing values.  In future will be simplier to add user changable timings.
+typedef struct  {
+	uint16_t  START_GAP;
+	uint16_t  WRITE_GAP;
+	uint16_t  WRITE_0;
+	uint16_t  WRITE_1;
+	uint16_t  WRITE_2;
+	uint16_t  WRITE_3;
+	uint16_t  READ_GAP;
+} T55xx_Timing;
+
+// Set Initial/Default Values.  Note: *8 can occure when used.  This should keep things simplier here.
+T55xx_Timing T55xx_Timing_FixedBit = { 31 * 8   , 20 * 8   , 18 * 8 , 50 * 8 , 0      , 0      , 15 * 8   };
+T55xx_Timing T55xx_Timing_LLR      = { 31 * 8   , 20 * 8   , 18 * 8 , 50 * 8 , 0      , 0      , 15 * 8   };
+T55xx_Timing T55xx_Timing_Leading0 = { 31 * 8   , 20 * 8   , 18 * 8 , 40 * 8 , 0      , 0      , 15 * 8   };
+T55xx_Timing T55xx_Timing_1of4     = { 31 * 8   , 20 * 8   , 18 * 8 , 34 * 8 , 50 * 8 , 66 * 8 , 15 * 8   };
+
+// Some defines for readability
+#define T55xx_DLMode_Fixed         0 // Default Mode
+#define T55xx_DLMode_LLR           1 // Long Leading Reference
+#define T55xx_DLMode_Leading0      2 // Leading Zero
+#define T55xx_DLMode_1of4          3 // 1 of 4
+#define T55xx_LongLeadingReference 4 // Value to tell Write Bit to send long reference
+// Macro for code readability
+#define BitStream_Byte(X) ((X) >> 3)
+#define BitStream_Bit(X)  ((X) &  7)  
+
 
 void TurnReadLFOn(int delay) {
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
 	// Give it a bit of time for the resonant antenna to settle.
-	SpinDelayUs(delay); //155*8 //50*8
+	WaitUS(delay); //155*8 //50*8
 }
 
 // Write one bit to card
-void T55xxWriteBit(int bit) {
-	if (!bit)
-		TurnReadLFOn(WRITE_0);
+void T55xxWriteBit(int bit, T55xx_Timing *Timings) {
+
+	// If bit = 4 Send Long Leading Reference which is 138 + WRITE_0	
+	// Dbprintf ("Bits : %d",bit);
+	switch (bit){
+		case 0 : TurnReadLFOn(Timings->WRITE_0);             break; // Send bit  0/00
+		case 1 : TurnReadLFOn(Timings->WRITE_1);             break; // Send bit  1/01
+		case 2 : TurnReadLFOn(Timings->WRITE_2);             break; // Send bits   10
+		case 3 : TurnReadLFOn(Timings->WRITE_3);             break; // Send bits   11
+		case 4 : TurnReadLFOn(Timings->WRITE_0 + (136 * 8)); break; // Send Long Leading Reference
+	}
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
+	WaitUS(Timings->WRITE_GAP);
+}
+
+// Function to abstract an Arbitrary length byte array to store bit pattern.
+// bit_array    - Array to hold data/bit pattern
+// start_offset - bit location to start storing new bits.
+// data         - upto 32 bits of data to store
+// num_bits     - how many bits (low x bits of data)  Max 32 bits at a time
+// max_len         - how many bytes can the bit_array hold (ensure no buffer overflow)
+// returns "Next" bit offset / bits stored (for next store)
+//int T55xx_SetBits (uint8_t *bit_array, int start_offset, uint32_t data      , int num_bits, int max_len)
+int T55xx_SetBits (uint8_t *BitStream, uint8_t start_offset, uint32_t data , uint8_t num_bits, uint8_t max_len)
+{
+	int8_t offset;
+	int8_t NextOffset = start_offset;
+
+	// Check if data will fit.
+	if ((start_offset + num_bits) <= (max_len*8)) {
+		// Loop through the data and store
+		for (offset = (num_bits-1); offset >= 0; offset--) {
+
+			if ((data >> offset) & 1)  BitStream[BitStream_Byte(NextOffset)] |= (1         << BitStream_Bit(NextOffset));     // Set the bit to 1
+			else                       BitStream[BitStream_Byte(NextOffset)] &= (0xff ^ (1 << BitStream_Bit(NextOffset)));    // Set the bit to 0
+
+			NextOffset++;
+		}
+	}
+	else {
+		// Note: This should never happen unless some code changes cause it.  
+		// So short message for coders when testing.
+		Dbprintf ("T55 too many bits"); 
+	}
+	return NextOffset;
+}
+
+// Send one downlink command to the card 
+void T55xx_SendCMD (uint32_t Data, uint32_t Block, uint32_t Pwd, uint8_t arg) { 
+
+	/*
+		arg bits
+		xxxxxxx1 0x01 PwdMode
+		xxxxxx1x 0x02 Page
+		xxxxx1xx 0x04 testMode
+		xxx11xxx 0x18 downlink mode
+		xx1xxxxx 0x20 !reg_readmode
+		x1xxxxxx 0x40 called for a read, so no data packet
+		1xxxxxxx 0x80 reset
+
+	*/
+	bool PwdMode      = ((arg & 0x01) == 0x01);
+	bool Page         =  (arg & 0x02);
+	bool testMode     = ((arg & 0x04) == 0x04);
+	uint8_t downlink_mode = (arg >> 3) & 0x03;
+	bool reg_readmode = ((arg & 0x20) == 0x20);
+	bool read_cmd     = ((arg & 0x40) == 0x40);
+	bool reset        =  (arg & 0x80);
+
+	uint8_t i = 0;
+	uint8_t BitStream[10];  // Max Downlink Command size ~74 bits, so 10 bytes (80 bits)
+	uint8_t BitStreamLen;
+	T55xx_Timing *Timing;
+	uint8_t SendBits;
+
+	// Assigning Downlink Timeing for write
+	switch (downlink_mode)
+	{
+		case T55xx_DLMode_Fixed    : Timing = &T55xx_Timing_FixedBit;  break; 
+		case T55xx_DLMode_LLR      : Timing = &T55xx_Timing_LLR;       break;
+		case T55xx_DLMode_Leading0 : Timing = &T55xx_Timing_Leading0;  break;
+		case T55xx_DLMode_1of4     : Timing = &T55xx_Timing_1of4;      break;
+		default:
+				Timing = &T55xx_Timing_FixedBit;
+	}
+
+	// Build Bit Stream to send.
+	memset (BitStream,0x00,sizeof(BitStream));
+	
+	BitStreamLen = 0; // Ensure 0 bit index to start.
+	
+	// Add Leading 0 and 1 of 4 reference bit
+	if ((downlink_mode == T55xx_DLMode_Leading0) || (downlink_mode == T55xx_DLMode_1of4))
+		BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen, 0, 1,sizeof(BitStream)); 
+
+	// Add extra reference 0 for 1 of 4
+	if (downlink_mode == T55xx_DLMode_1of4)
+		BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen, 0, 1,sizeof(BitStream)); 
+
+	// Add Opcode 
+	if (reset) {
+		//  Reset : r*) 00
+		BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen, 0, 2,sizeof(BitStream)); 
+	}
 	else
-		TurnReadLFOn(WRITE_1);
+	{
+		if (testMode) Dbprintf("TestMODE");
+		BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen,testMode ? 0 : 1    , 1,sizeof(BitStream));
+		BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen,testMode ? 1 : Page , 1,sizeof(BitStream));
+
+		if (PwdMode) {
+			// Leading 0 and 1 of 4 00 fixed bits if passsword used		
+			if ((downlink_mode == T55xx_DLMode_Leading0) || (downlink_mode == T55xx_DLMode_1of4)) {
+				BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen, 0, 2,sizeof(BitStream));
+			}
+			BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen, Pwd, 32,sizeof(BitStream));
+		}
+
+		// Add Lock bit 0
+		if (!reg_readmode) BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen, 0, 1,sizeof(BitStream));
+
+		// Add Data if a write command
+		if (!read_cmd)	BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen, Data, 32,sizeof(BitStream));
+
+		// Add Address
+		if (!reg_readmode) BitStreamLen = T55xx_SetBits (BitStream, BitStreamLen, Block, 3,sizeof(BitStream));
+	}
+
+	// Send Bits to T55xx
+	// Set up FPGA, 125kHz
+	LFSetupFPGAForADC(95, true);
+	StartTicks();
+	// make sure tag is fully powered up...
+	WaitMS(5);
+	// Trigger T55x7 in mode.
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	SpinDelayUs(WRITE_GAP);
+	WaitUS(Timing->START_GAP);
+
+	// If long leading 0 send long reference pulse
+	if (downlink_mode ==  T55xx_DLMode_LLR) 
+		T55xxWriteBit (T55xx_LongLeadingReference,Timing); // Send Long Leading Start Reference
+
+	if ((downlink_mode ==  T55xx_DLMode_1of4) && (BitStreamLen > 0)) { // 1 of 4 need to send 2 bits at a time
+		for ( i = 0; i < BitStreamLen-1; i+=2 ) {
+			SendBits  = (BitStream[BitStream_Byte(i  )] >> (BitStream_Bit(i  )) & 1) << 1;   // Bit i
+			SendBits += (BitStream[BitStream_Byte(i+1)] >> (BitStream_Bit(i+1)) & 1);        // Bit i+1;
+			T55xxWriteBit (SendBits & 3,Timing);
+		}
+	}
+	else {
+		for (i = 0; i < BitStreamLen; i++) {
+			SendBits = (BitStream[BitStream_Byte(i)] >> BitStream_Bit(i));
+			T55xxWriteBit (SendBits & 1,Timing);
+		}
+	}
 }
 
 // Send T5577 reset command then read stream (see if we can identify the start of the stream)
 void T55xxResetRead(void) {
 	LED_A_ON();
-	//clear buffer now so it does not interfere with timing later
-	BigBuf_Clear_ext(false);
 
-	// Set up FPGA, 125kHz
-	LFSetupFPGAForADC(95, true);
+	//  send  r* 00 
+	uint8_t arg = 0x80;  // SendCMD will add correct reference mode based on flags (when added).
 
-	// Trigger T55x7 in mode.
-	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	SpinDelayUs(START_GAP);
+	// Add in downlink_mode when ready
+	//    arg |= 0x00;  // dlmode << 3  (00 default - 08 leading 0 - 10 Fixed - 18 1 of 4 )
 
-	// reset tag - op code 00
-	T55xxWriteBit(0);
-	T55xxWriteBit(0);
+	//clear buffer now so it does not interfere with timing later
+	BigBuf_Clear_keep_EM();
 
-	// Turn field on to read the response
-	TurnReadLFOn(READ_GAP);
+	T55xx_SendCMD (0, 0, 0, arg); //, true);
+
+	TurnReadLFOn(T55xx_Timing_FixedBit.READ_GAP);
 
 	// Acquisition
-	doT55x7Acquisition(BigBuf_max_traceLen());
+	DoPartialAcquisition(0, true, BigBuf_max_traceLen(), 0);
 
 	// Turn the field off
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
@@ -1126,125 +1462,126 @@ void T55xxResetRead(void) {
 }
 
 // Write one card block in page 0, no lock
-void T55xxWriteBlockExt(uint32_t Data, uint32_t Block, uint32_t Pwd, uint8_t arg) {
-	LED_A_ON();
-	bool PwdMode = arg & 0x1;
-	uint8_t Page = (arg & 0x2)>>1;
-	uint32_t i = 0;
-
-	// Set up FPGA, 125kHz
-	LFSetupFPGAForADC(95, true);
-
-	// Trigger T55x7 in mode.
-	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	SpinDelayUs(START_GAP);
-
-	// Opcode 10
-	T55xxWriteBit(1);
-	T55xxWriteBit(Page); //Page 0
-	if (PwdMode){
-		// Send Pwd
-		for (i = 0x80000000; i != 0; i >>= 1)
-			T55xxWriteBit(Pwd & i);
-	}
-	// Send Lock bit
-	T55xxWriteBit(0);
-
-	// Send Data
-	for (i = 0x80000000; i != 0; i >>= 1)
-		T55xxWriteBit(Data & i);
-
-	// Send Block number
-	for (i = 0x04; i != 0; i >>= 1)
-		T55xxWriteBit(Block & i);
+void T55xxWriteBlock(uint32_t Data, uint32_t Block, uint32_t Pwd, uint8_t arg) {
+	/*
+		arg bits
+		xxxxxxx1 0x01 PwdMode
+		xxxxxx1x 0x02 Page
+		xxxxx1xx 0x04 testMode
+		xxx11xxx 0x18 downlink mode
+		xx1xxxxx 0x20 !reg_readmode
+		x1xxxxxx 0x40 called for a read, so no data packet
+		1xxxxxxx 0x80 reset
+	*/
+	
+	bool testMode = ((arg & 0x04) == 0x04);
+	arg &= (0xff ^ 0x40); // Called for a write, so ensure it is clear/0
+	
+	LED_A_ON ();
+	T55xx_SendCMD (Data, Block, Pwd, arg) ;//, false); 
 
 	// Perform write (nominal is 5.6 ms for T55x7 and 18ms for E5550,
 	// so wait a little more)
-	TurnReadLFOn(20 * 1000);
+
+	// "there is a clock delay before programming" 
+	//  - programming takes ~5.6ms for t5577 ~18ms for E5550 or t5567
+	//  so we should wait 1 clock + 5.6ms then read response? 
+	//  but we need to know we are dealing with t5577 vs t5567 vs e5550 (or q5) marshmellow...
+	if (testMode) {
+		//TESTMODE TIMING TESTS: 
+		// <566us does nothing 
+		// 566-568 switches between wiping to 0s and doing nothing
+		// 5184 wipes and allows 1 block to be programmed.
+		// indefinite power on wipes and then programs all blocks with bitshifted data sent.
+		TurnReadLFOn(5184); 
+
+	} else {
+		TurnReadLFOn(20 * 1000);
 		//could attempt to do a read to confirm write took
 		// as the tag should repeat back the new block 
 		// until it is reset, but to confirm it we would 
-		// need to know the current block 0 config mode
+		// need to know the current block 0 config mode for
+		// modulation clock an other details to demod the response...
+		// response should be (for t55x7) a 0 bit then (ST if on) 
+		// block data written in on repeat until reset. 
 
+		//DoPartialAcquisition(20, true, 12000);
+	}
 	// turn field off
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	LED_A_OFF();
-}
 
-// Write one card block in page 0, no lock
-void T55xxWriteBlock(uint32_t Data, uint32_t Block, uint32_t Pwd, uint8_t arg) {
-	T55xxWriteBlockExt(Data, Block, Pwd, arg);
 	cmd_send(CMD_ACK,0,0,0,0,0);
+
+	LED_A_OFF ();
 }
 
 // Read one card block in page [page]
-void T55xxReadBlock(uint16_t arg0, uint8_t Block, uint32_t Pwd) {
+void T55xxReadBlock (uint16_t arg0, uint8_t Block, uint32_t Pwd) {//, struct T55xx_Timing *Timing) {
+
 	LED_A_ON();
-	bool PwdMode = arg0 & 0x1;
-	uint8_t Page = (arg0 & 0x2) >> 1;
-	uint32_t i = 0;
-	bool RegReadMode = (Block == 0xFF);
 
-	//clear buffer now so it does not interfere with timing later
-	BigBuf_Clear_ext(false);
+	/*
+		arg bits
+		xxxxxxx1 0x01 PwdMode
+		xxxxxx1x 0x02 Page
+		xxxxx1xx 0x04 testMode
+		xxx11xxx 0x18 downlink mode
+		xx1xxxxx 0x20 !reg_readmode
+		x1xxxxxx 0x40 called for a read, so no data packet
+		1xxxxxxx 0x80 reset
+	*/
+
+	// Set Read Flag to ensure SendCMD does not add "data" to the packet
+	arg0 |= 0x40;
 
+	// RegRead Mode true of block 0xff
+	if (Block == 0xff) arg0 |= 0x20;
+	
 	//make sure block is at max 7
 	Block &= 0x7;
 
-	// Set up FPGA, 125kHz to power up the tag
-	LFSetupFPGAForADC(95, true);
-
-	// Trigger T55x7 Direct Access Mode with start gap
-	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	SpinDelayUs(START_GAP);
-
-	// Opcode 1[page]
-	T55xxWriteBit(1);
-	T55xxWriteBit(Page); //Page 0
-
-	if (PwdMode){
-		// Send Pwd
-		for (i = 0x80000000; i != 0; i >>= 1)
-			T55xxWriteBit(Pwd & i);
-	}
-	// Send a zero bit separation
-	T55xxWriteBit(0);
+	//clear buffer now so it does not interfere with timing later
+	BigBuf_Clear_ext(false);
 
-	// Send Block number (if direct access mode)
-	if (!RegReadMode)
-		for (i = 0x04; i != 0; i >>= 1)
-			T55xxWriteBit(Block & i);		
+	T55xx_SendCMD (0, Block, Pwd, arg0); //, true);
 
 	// Turn field on to read the response
-	TurnReadLFOn(READ_GAP);
+	// 137*8 seems to get to the start of data pretty well... 
+	//  but we want to go past the start and let the repeating data settle in...
+	TurnReadLFOn(210*8); 
 
 	// Acquisition
-	doT55x7Acquisition(12000);
+	// Now do the acquisition
+	DoPartialAcquisition(0, true, 12000, 0);
 
 	// Turn the field off
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
 	cmd_send(CMD_ACK,0,0,0,0,0);    
+
 	LED_A_OFF();
 }
 
 void T55xxWakeUp(uint32_t Pwd){
 	LED_B_ON();
-	uint32_t i = 0;
-	
-	// Set up FPGA, 125kHz
-	LFSetupFPGAForADC(95, true);
-	
-	// Trigger T55x7 Direct Access Mode
-	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
-	SpinDelayUs(START_GAP);
-	
-	// Opcode 10
-	T55xxWriteBit(1);
-	T55xxWriteBit(0); //Page 0
+	/*
+		arg bits
+		xxxxxxx1 0x01 PwdMode
+		xxxxxx1x 0x02 Page
+		xxxxx1xx 0x04 testMode
+		xxx11xxx 0x18 downlink mode
+		xx1xxxxx 0x20 !reg_readmode 
+		x1xxxxxx 0x40 called for a read, so no data packet
+		1xxxxxxx 0x80 reset
+	*/
+
+	// r* 10 (00) <pwd>   r* for llr , L0 and 1/4 - (00) for L0 and 1/4 - All handled in SendCMD
+	// So, default Opcode 10 and pwd.
+	uint8_t arg = 0x01 | 0x40 | 0x20; //Password Read Call no data | reg_read no block
 
-	// Send Pwd
-	for (i = 0x80000000; i != 0; i >>= 1)
-		T55xxWriteBit(Pwd & i);
+	// Add in downlink_mode when ready
+	//    arg |= 0x00;  // dlmode << 3  (00 default - 08 leading 0 - 10 Fixed - 18 1 of 4 )
+
+	T55xx_SendCMD (0, 0, Pwd, arg); //, true);
 
 	// Turn and leave field on to let the begin repeating transmission
 	TurnReadLFOn(20*1000);
@@ -1255,15 +1592,14 @@ void T55xxWakeUp(uint32_t Pwd){
 void WriteT55xx(uint32_t *blockdata, uint8_t startblock, uint8_t numblocks) {
 	// write last block first and config block last (if included)
 	for (uint8_t i = numblocks+startblock; i > startblock; i--) {
-		//Dbprintf("write- Blk: %d, d:%08X",i-1,blockdata[i-1]);
-		T55xxWriteBlockExt(blockdata[i-1],i-1,0,0);
+		T55xxWriteBlock(blockdata[i-1],i-1,0,0);//,false); //,&T55xx_Timing_FixedBit);
+		//T55xx_SendCMD (blockdata[i-1],i-1,0,0);//,false); //,&T55xx_Timing_FixedBit);
 	}
 }
 
-// Copy HID id to card and setup block 0 config
-void CopyHIDtoT55x7(uint32_t hi2, uint32_t hi, uint32_t lo, uint8_t longFMT) {
+// Copy a HID-like card (e.g. HID Proximity, Paradox) to a T55x7 compatible card
+void CopyHIDtoT55x7(uint32_t hi2, uint32_t hi, uint32_t lo, uint8_t longFMT, uint8_t preamble) {
 	uint32_t data[] = {0,0,0,0,0,0,0};
-	//int data1=0, data2=0, data3=0, data4=0, data5=0, data6=0; //up to six blocks for long format
 	uint8_t last_block = 0;
 
 	if (longFMT) {
@@ -1274,15 +1610,15 @@ void CopyHIDtoT55x7(uint32_t hi2, uint32_t hi, uint32_t lo, uint8_t longFMT) {
 		}
 		// Build the 6 data blocks for supplied 84bit ID
 		last_block = 6;
-		// load preamble (1D) & long format identifier (9E manchester encoded)
-		data[1] = 0x1D96A900 | (manchesterEncode2Bytes((hi2 >> 16) & 0xF) & 0xFF);
+		// load preamble & long format identifier (9E manchester encoded)
+		data[1] = (preamble << 24) | 0x96A900 | (manchesterEncode2Bytes((hi2 >> 16) & 0xF) & 0xFF);
 		// load raw id from hi2, hi, lo to data blocks (manchester encoded)
 		data[2] = manchesterEncode2Bytes(hi2 & 0xFFFF);
 		data[3] = manchesterEncode2Bytes(hi >> 16);
 		data[4] = manchesterEncode2Bytes(hi & 0xFFFF);
 		data[5] = manchesterEncode2Bytes(lo >> 16);
 		data[6] = manchesterEncode2Bytes(lo & 0xFFFF);
-	}	else {
+	} else {
 		// Ensure no more than 44 bits supplied
 		if (hi>0xFFF) {
 			DbpString("Tags can only have 44 bits.");
@@ -1291,7 +1627,7 @@ void CopyHIDtoT55x7(uint32_t hi2, uint32_t hi, uint32_t lo, uint8_t longFMT) {
 		// Build the 3 data blocks for supplied 44bit ID
 		last_block = 3;
 		// load preamble
-		data[1] = 0x1D000000 | (manchesterEncode2Bytes(hi) & 0xFFFFFF);
+		data[1] = (preamble << 24) | (manchesterEncode2Bytes(hi) & 0xFFFFFF);
 		data[2] = manchesterEncode2Bytes(lo >> 16);
 		data[3] = manchesterEncode2Bytes(lo & 0xFFFF);
 	}
@@ -1344,15 +1680,24 @@ void CopyIndala224toT55x7(uint32_t uid1, uint32_t uid2, uint32_t uid3, uint32_t
 	//Program the 7 data blocks for supplied 224bit UID
 	uint32_t data[] = {0, uid1, uid2, uid3, uid4, uid5, uid6, uid7};
 	// and the block 0 for Indala224 format	
-	//Config for Indala (RF/32;PSK1 with RF/2;Maxblock=7)
-	data[0] = T55x7_BITRATE_RF_32 | T55x7_MODULATION_PSK1 | (7 << T55x7_MAXBLOCK_SHIFT);
+	//Config for Indala (RF/32;PSK2 with RF/2;Maxblock=7)
+	data[0] = T55x7_BITRATE_RF_32 | T55x7_MODULATION_PSK2 | (7 << T55x7_MAXBLOCK_SHIFT);
 	//TODO add selection of chip for Q5 or T55x7
-	// data[0] = (((32-2)/2)<<T5555_BITRATE_SHIFT) | T5555_MODULATION_PSK1 | 7 << T5555_MAXBLOCK_SHIFT;
+	// data[0] = (((32-2)>>1)<<T5555_BITRATE_SHIFT) | T5555_MODULATION_PSK2 | 7 << T5555_MAXBLOCK_SHIFT;
 	WriteT55xx(data, 0, 8);
 	//Alternative config for Indala (Extended mode;RF/32;PSK1 with RF/2;Maxblock=7;Inverse data)
 	//	T5567WriteBlock(0x603E10E2,0);
 	DbpString("DONE!");
 }
+// clone viking tag to T55xx
+void CopyVikingtoT55xx(uint32_t block1, uint32_t block2, uint8_t Q5) {
+	uint32_t data[] = {T55x7_BITRATE_RF_32 | T55x7_MODULATION_MANCHESTER | (2 << T55x7_MAXBLOCK_SHIFT), block1, block2};
+	if (Q5) data[0] = T5555_SET_BITRATE(32) | T5555_MODULATION_MANCHESTER | 2 << T5555_MAXBLOCK_SHIFT;
+	// Program the data blocks for supplied ID and the block 0 config
+	WriteT55xx(data, 0, 3);
+	LED_D_OFF();
+	cmd_send(CMD_ACK,0,0,0,0,0);
+}
 
 // Define 9bit header for EM410x tags
 #define EM410X_HEADER		  0x1FF
@@ -1418,7 +1763,7 @@ void WriteEM410x(uint32_t card, uint32_t id_hi, uint32_t id_lo) {
 	LED_D_ON();
 
 	// Write EM410x ID
-	uint32_t data[] = {0, id>>32, id & 0xFFFFFFFF};
+	uint32_t data[] = {0, (uint32_t)(id>>32), (uint32_t)(id & 0xFFFFFFFF)};
 
 	clock = (card & 0xFF00) >> 8;
 	clock = (clock == 0) ? 64 : clock;
@@ -1431,8 +1776,7 @@ void WriteEM410x(uint32_t card, uint32_t id_hi, uint32_t id_lo) {
 		}
 		data[0] = clock | T55x7_MODULATION_MANCHESTER | (2 << T55x7_MAXBLOCK_SHIFT);
 	} else { //t5555 (Q5)
-		clock = (clock-2)>>1;  //n = (RF-2)/2
-		data[0] = (clock << T5555_BITRATE_SHIFT) | T5555_MODULATION_MANCHESTER | (2 << T5555_MAXBLOCK_SHIFT);
+		data[0] = T5555_SET_BITRATE(clock) | T5555_MODULATION_MANCHESTER | (2 << T5555_MAXBLOCK_SHIFT);
 	}
 
 	WriteT55xx(data, 0, 3);
@@ -1449,7 +1793,7 @@ void WriteEM410x(uint32_t card, uint32_t id_hi, uint32_t id_lo) {
 #define FWD_CMD_WRITE 0xA
 #define FWD_CMD_READ 0x9
 #define FWD_CMD_DISABLE 0x5
-
+#define FWD_CMD_PROTECT 0x3
 
 uint8_t forwardLink_data[64]; //array of forwarded bits
 uint8_t * forward_ptr; //ptr for forward message preparation
@@ -1470,7 +1814,6 @@ uint8_t * fwd_write_ptr; //forwardlink bit pointer
 //  WRITE_0 = 23*8 , 9*8  SpinDelayUs(23*8); 
 
 uint8_t Prepare_Cmd( uint8_t cmd ) {
-	//--------------------------------------------------------------------
 
 	*forward_ptr++ = 0; //start bit
 	*forward_ptr++ = 0; //second pause for 4050 code
@@ -1490,10 +1833,7 @@ uint8_t Prepare_Cmd( uint8_t cmd ) {
 // prepares address bits
 // see EM4469 spec
 //====================================================================
-
-//--------------------------------------------------------------------
 uint8_t Prepare_Addr( uint8_t addr ) {
-	//--------------------------------------------------------------------
 
 	register uint8_t line_parity;
 
@@ -1514,10 +1854,7 @@ uint8_t Prepare_Addr( uint8_t addr ) {
 // prepares data bits intreleaved with parity bits
 // see EM4469 spec
 //====================================================================
-
-//--------------------------------------------------------------------
 uint8_t Prepare_Data( uint16_t data_low, uint16_t data_hi) {
-	//--------------------------------------------------------------------
 
 	register uint8_t line_parity;
 	register uint8_t column_parity;
@@ -1559,31 +1896,27 @@ void SendForward(uint8_t fwd_bit_count) {
 	fwd_write_ptr = forwardLink_data;
 	fwd_bit_sz = fwd_bit_count;
 
-	LED_D_ON();
-
-	// Set up FPGA, 125kHz
+	// Set up FPGA, 125kHz or 95 divisor
 	LFSetupFPGAForADC(95, true);
 
 	// force 1st mod pulse (start gap must be longer for 4305)
 	fwd_bit_sz--; //prepare next bit modulation
 	fwd_write_ptr++;
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
-	SpinDelayUs(55*8); //55 cycles off (8us each)for 4305
-	FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz
+	WaitUS(55*8); //55 cycles off (8us each)for 4305  //another reader has 37 here...
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);//field on
-	SpinDelayUs(16*8); //16 cycles on (8us each)
+	WaitUS(18*8); //18 cycles on (8us each)
 
-	// now start writting
+	// now start writting - each bit should be 32*8 total length
 	while(fwd_bit_sz-- > 0) { //prepare next bit modulation
 		if(((*fwd_write_ptr++) & 1) == 1)
-			SpinDelayUs(32*8); //32 cycles at 125Khz (8us each)
+			WaitUS(32*8); //32 cycles at 125Khz (8us each)
 		else {
 			//These timings work for 4469/4269/4305 (with the 55*8 above)
 			FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
-			SpinDelayUs(23*8); //16-4 cycles off (8us each)
-			FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 95); //125Khz
+			WaitUS(23*8); //23 cycles off (8us each)
 			FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);//field on
-			SpinDelayUs(9*8); //16 cycles on (8us each)
+			WaitUS((32-23)*8); //remaining cycles on (8us each)
 		}
 	}
 }
@@ -1600,19 +1933,17 @@ void EM4xLogin(uint32_t Password) {
 
 	//Wait for command to complete
 	SpinDelay(20);
-
 }
 
 void EM4xReadWord(uint8_t Address, uint32_t Pwd, uint8_t PwdMode) {
 
 	uint8_t fwd_bit_count;
-	uint8_t *dest = BigBuf_get_addr();
-	uint16_t bufferlength = BigBuf_max_traceLen();
-	uint32_t i = 0;
 
 	// Clear destination buffer before sending the command
-	memset(dest, 0x80, bufferlength);
+	BigBuf_Clear_ext(false);
 
+	LED_A_ON();
+	StartTicks();
 	//If password mode do login
 	if (PwdMode == 1) EM4xLogin(Pwd);
 
@@ -1620,36 +1951,29 @@ void EM4xReadWord(uint8_t Address, uint32_t Pwd, uint8_t PwdMode) {
 	fwd_bit_count = Prepare_Cmd( FWD_CMD_READ );
 	fwd_bit_count += Prepare_Addr( Address );
 
-	// Connect the A/D to the peak-detected low-frequency path.
-	SetAdcMuxFor(GPIO_MUXSEL_LOPKD);
-	// Now set up the SSC to get the ADC samples that are now streaming at us.
-	FpgaSetupSsc();
-
 	SendForward(fwd_bit_count);
-
+	WaitUS(400);
 	// Now do the acquisition
-	i = 0;
-	for(;;) {
-		if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_TXRDY) {
-			AT91C_BASE_SSC->SSC_THR = 0x43;
-		}
-		if (AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY) {
-			dest[i] = (uint8_t)AT91C_BASE_SSC->SSC_RHR;
-			i++;
-			if (i >= bufferlength) break;
-		}
-	}
+	DoPartialAcquisition(20, true, 6000, 1000);
+	
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
+	LED_A_OFF();
 	cmd_send(CMD_ACK,0,0,0,0,0);
-	LED_D_OFF();
 }
 
-void EM4xWriteWord(uint32_t Data, uint8_t Address, uint32_t Pwd, uint8_t PwdMode) {
-
+void EM4xWriteWord(uint32_t flag, uint32_t Data, uint32_t Pwd) {
+	
+	bool PwdMode = (flag & 0x1);
+	uint8_t Address = (flag >> 8) & 0xFF;
 	uint8_t fwd_bit_count;
 
+	//clear buffer now so it does not interfere with timing later
+	BigBuf_Clear_ext(false);
+
+	LED_A_ON();
+	StartTicks();
 	//If password mode do login
-	if (PwdMode == 1) EM4xLogin(Pwd);
+	if (PwdMode) EM4xLogin(Pwd);
 
 	forward_ptr = forwardLink_data;
 	fwd_bit_count = Prepare_Cmd( FWD_CMD_WRITE );
@@ -1659,7 +1983,105 @@ void EM4xWriteWord(uint32_t Data, uint8_t Address, uint32_t Pwd, uint8_t PwdMode
 	SendForward(fwd_bit_count);
 
 	//Wait for write to complete
-	SpinDelay(20);
+	//SpinDelay(10);
+
+	WaitUS(6500);
+	//Capture response if one exists
+	DoPartialAcquisition(20, true, 6000, 1000);
+
 	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
-	LED_D_OFF();
+	LED_A_OFF();
+	cmd_send(CMD_ACK,0,0,0,0,0);
+}
+
+void EM4xProtect(uint32_t flag, uint32_t Data, uint32_t Pwd) {
+	
+	bool PwdMode = (flag & 0x1);
+	uint8_t fwd_bit_count;
+
+	//clear buffer now so it does not interfere with timing later
+	BigBuf_Clear_ext(false);
+
+	LED_A_ON();
+	StartTicks();
+	//If password mode do login
+	if (PwdMode) EM4xLogin(Pwd);
+
+	forward_ptr = forwardLink_data;
+	fwd_bit_count = Prepare_Cmd( FWD_CMD_PROTECT );
+
+	//unsure if this needs the full packet config...
+	fwd_bit_count += Prepare_Data( Data&0xFFFF, Data>>16 );
+
+	SendForward(fwd_bit_count);
+
+	//Wait for write to complete
+	//SpinDelay(10);
+
+	WaitUS(6500);
+	//Capture response if one exists
+	DoPartialAcquisition(20, true, 6000, 1000);
+
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
+	LED_A_OFF();
+	cmd_send(CMD_ACK,0,0,0,0,0);
+}
+/*
+Reading a COTAG.
+
+COTAG needs the reader to send a startsequence and the card has an extreme slow datarate.
+because of this, we can "sample" the data signal but we interpreate it to Manchester direct.
+
+READER START SEQUENCE:
+burst 800 us,    gap   2.2 msecs
+burst 3.6 msecs  gap   2.2 msecs
+burst 800 us     gap   2.2 msecs
+pulse 3.6 msecs
+
+This triggers a COTAG tag to response
+*/
+void Cotag(uint32_t arg0) {
+
+#define OFF     { FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); WaitUS(2035); }
+#define ON(x)   { FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD); WaitUS((x)); }
+
+	uint8_t rawsignal = arg0 & 0xF;
+
+	LED_A_ON();
+
+	// Switching to LF image on FPGA. This might empty BigBuff
+	FpgaDownloadAndGo(FPGA_BITSTREAM_LF);
+
+	//clear buffer now so it does not interfere with timing later
+	BigBuf_Clear_ext(false);
+
+	// Set up FPGA, 132kHz to power up the tag
+	FpgaSendCommand(FPGA_CMD_SET_DIVISOR, 89);
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_LF_ADC | FPGA_LF_ADC_READER_FIELD);
+
+	// Connect the A/D to the peak-detected low-frequency path.
+	SetAdcMuxFor(GPIO_MUXSEL_LOPKD);
+
+	// Now set up the SSC to get the ADC samples that are now streaming at us.
+	FpgaSetupSsc(FPGA_MAJOR_MODE_LF_ADC);
+
+	// start clock - 1.5ticks is 1us
+	StartTicks();
+
+	//send COTAG start pulse
+	ON(740)  OFF
+	ON(3330) OFF
+	ON(740)  OFF
+	ON(1000)
+
+	switch(rawsignal) {
+		case 0: doCotagAcquisition(50000); break;
+		case 1: doCotagAcquisitionManchester(); break;
+		case 2: DoAcquisition_config(true, 0); break;
+	}
+
+	// Turn the field off
+	FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF); // field off
+	cmd_send(CMD_ACK,0,0,0,0,0);
+	LED_A_OFF();
 }