add the possibility to monitor the JTAG state machine

[usb-driver] / README

diff --git a/README b/README
index 277ffe6eff675fc81608aa94924cb546dca8e4de..dbb3b9dfa4302029451efe469f371c108dea6656 100644 (file)
--- a/README
+++ b/README
@@ -9,12 +9,20 @@ should work on every kernel version which is supported by libusb and supports
 ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
 the following software:
 
 ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
 the following software:
 

+ * ISE Webpack 9.1SP3

  * ISE Webpack 9.1SP2
  * ISE Webpack 9.1SP1
  * ISE Webpack 8.2SP3
  * ISE Webpack 8.1SP3
  * ISE Webpack 9.1SP2
  * ISE Webpack 9.1SP1
  * ISE Webpack 8.2SP3
  * ISE Webpack 8.1SP3

+ * ChipScope 9.1.03i

  * ChipScope 9.1.02i
  * ChipScope 9.1.02i

+ * ChipScope 8.2.04i

  * EDK 8.2.02i
  * EDK 8.2.02i

+ * EDK 8.1.02i
+
+In addition to the XILINX USB and parallel cables, devices based on the FTDI
+2232 serial converter chip are also experimentally supported. This includes
+devices like the Amontec JTAGkey(-Tiny).

 
 Build the library by calling `make'.
 
 
 Build the library by calling `make'.
 


@@ -26,6 +34,12 @@ $ export LD_PRELOAD=/path/to/libusb-driver.so  (for sh shells)
 $ setenv LD_PRELOAD /path/to/libusb-driver.so  (for csh shells)
 $ impact
 
 $ setenv LD_PRELOAD /path/to/libusb-driver.so  (for csh shells)
 $ impact
 

+The source for this library can be found at:
+http://cvs.zerfleddert.de/cgi-bin/viewcvs.cgi/usb-driver/
+
+The main website is located at:
+http://www.rmdir.de/~michael/xilinx/
+

 
 Notes for the USB cable
 =======================
 
 Notes for the USB cable
 =======================


@@ -68,6 +82,11 @@ ppdev
 To use the device as an ordinary user, put the user in the group 'lp'
 
 
 To use the device as an ordinary user, put the user in the group 'lp'
 
 

+If you have an almost compatible cable which works with other software but not
+with Impact, try adding -DFORCE_PC3_IDENT to the CFLAGS line in the Makefile.
+This enables a hack by Stefan Ziegenbalg to force detection of a parallel cable.
+
+

 Parallel Cable IV is currently only supported in 'compatibility mode', as no
 attempt to configure the ECP registers is done by this library.
 
 Parallel Cable IV is currently only supported in 'compatibility mode', as no
 attempt to configure the ECP registers is done by this library.
 


@@ -78,6 +97,32 @@ HIGHZ instead of BYPASS" enabled in Edit -> Preferences -> iMPACT Configuration
 Preferences.
 If you are using batch mode, add the following line to your cmd file:
 setPreference -pref UseHighz:TRUE
 Preferences.
 If you are using batch mode, add the following line to your cmd file:
 setPreference -pref UseHighz:TRUE

-(This problem also occurs on windows and when using the real windrvr in linux and
-is solved with the same workaround. Impact 8.2 is working fine with the same
+(This problem also occurs on windows and when using the real windrvr in linux
+and is solved with the same workaround. Impact 8.2 is working fine with the same

 boards and designs)
 boards and designs)

+
+
+Notes for FTDI 2232 based cables
+================================
+
+To build the driver with FTDI 2232 support, you need to have libftdi and
+the libftdi development package installed. On debian, you can install both
+by installing 'libftdi-dev'.
+
+To set-up the device:
+1. Find out the vendor and product id of your cable using lsusb:
+   Bus 003 Device 005: ID 0403:cff8 Future Technology Devices ...
+                          ~~~~~~~~~
+
+2. Copy the sample libusb-driverrc to ~/.libusb-driverrc, edit it and replace
+   the vendor and product-id in the example file with the values from provided
+   in the lsusb-output. You can also change the 'parallel port' which is mapped
+   to this cable. Impact sees the device at that port as a Parallel Cable III.
+
+3. To use the device as an ordinary user, put the following line in a new file
+   in /etc/udev/rules.d/ and restart udev:
+   ACTION=="add", BUS=="usb", SYSFS{idVendor}=="0403", SYSFS{idProduct}=="cff8", MODE="666"
+   (replace the vendor and product id with your values)
+
+The support for FTDI 2232 based devices is experimental and they are currently
+significantly slower than the other supported cables.