update links for xc3sprog

[usb-driver] / README

diff --git a/README b/README
index a148bf39dabf7dd79a945876290da6ed7857f8df..f3eb7c98209c4df609e472506ae08479fa93be8a 100644 (file)
--- a/README
+++ b/README
@@ -9,6 +9,9 @@ should work on every kernel version which is supported by libusb and supports
 ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
 the following software:
 
 ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
 the following software:
 

+ * ISE 13.1
+ * ISE 12.1
+ * ISE Webpack 11.1

  * ISE Webpack 10.1
  * ISE Webpack 9.2SP1, SP2, SP3, SP4
  * ISE Webpack 9.1SP1, SP2, SP3
  * ISE Webpack 10.1
  * ISE Webpack 9.2SP1, SP2, SP3, SP4
  * ISE Webpack 9.1SP1, SP2, SP3


@@ -56,7 +59,7 @@ Notes for the USB cable
 
 To use the device as an ordinary user, put the following line in a new
 file "libusb-driver.rules" in /etc/udev/rules.d/ and restart udev:
 
 To use the device as an ordinary user, put the following line in a new
 file "libusb-driver.rules" in /etc/udev/rules.d/ and restart udev:

-ACTION=="add", BUS=="usb", SYSFS{idVendor}=="03fd", MODE="666"
+ACTION=="add", SUBSYSTEMS=="usb", ATTRS{idVendor}=="03fd", MODE="666"

 
 
 If your cable does not have the ID 03fd:0008 in the output of lsusb,
 
 
 If your cable does not have the ID 03fd:0008 in the output of lsusb,


@@ -64,15 +67,28 @@ the initial firmware has not been loaded (loading it changes the
 product-ID from another value to 8). To load the firmware follow
 these steps:
 
 product-ID from another value to 8). To load the firmware follow
 these steps:
 

+1. Run ./setup_pcusb in this directory, this should set up everything
+   correctly:
+   - When $XILINX is set correctly:
+     $ ./setup_pcusb
+   - When $XILINX is not set, and ISE is installed in /opt/Xilinx/13.1:
+     $ ./setup_pcusb /opt/Xilinx/13.1/ISE_DS/ISE
+
+Old instructions, use only when the above script did not work:
+

 1. If you have no /etc/udev/rules.d/xusbdfwu.rules file, copy it from
    /path/to/ISE/bin/lin/xusbdfwu.rules to /etc/udev/rules.d/xusbdfwu.rules
 
 1. If you have no /etc/udev/rules.d/xusbdfwu.rules file, copy it from
    /path/to/ISE/bin/lin/xusbdfwu.rules to /etc/udev/rules.d/xusbdfwu.rules
 

-2. Install the package containing /sbin/fxload from your linux distribution.
+2. If you are running a newer version of udev (as in Debian Squeeze and
+   Ubuntu 9.10), you need to adapt the rules-file to the new udev-version:
+   sed -i -e 's/TEMPNODE/tempnode/' -e 's/SYSFS/ATTRS/g' -e 's/BUS/SUBSYSTEMS/' /etc/udev/rules.d/xusbdfwu.rules
+
+3. Install the package containing /sbin/fxload from your linux distribution.

    It is usually called "fxload"
 
    It is usually called "fxload"
 

-3. copy the files /path/to/ISE/bin/lin/xusb*.hex to /usr/share/
+4. copy the files /path/to/ISE/bin/lin/xusb*.hex to /usr/share/

 
 

-4. restart udev and re-plug the cable
+5. restart udev and re-plug the cable

 
 
 If you have multiple cables connected, you can specify the cable to use
 
 
 If you have multiple cables connected, you can specify the cable to use


@@ -139,7 +155,7 @@ To set-up the device:
 
 3. To use the device as an ordinary user, put the following line in a new file
    in /etc/udev/rules.d/ and restart udev:
 
 3. To use the device as an ordinary user, put the following line in a new file
    in /etc/udev/rules.d/ and restart udev:

-   ACTION=="add", BUS=="usb", SYSFS{idVendor}=="0403", SYSFS{idProduct}=="cff8", MODE="666"
+   ACTION=="add", SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="cff8", MODE="666"

    (replace the vendor and product id with your values)
 
 The support for FTDI 2232 based devices is experimental and they are currently
    (replace the vendor and product id with your values)
 
 The support for FTDI 2232 based devices is experimental and they are currently