add the possibility to monitor the JTAG state machine

[usb-driver] / README

diff --git a/README b/README
index 597b1b2313596ef03ba478bf7011ca686f320d06..dbb3b9dfa4302029451efe469f371c108dea6656 100644 (file)
--- a/README
+++ b/README
@@ -9,12 +9,20 @@ should work on every kernel version which is supported by libusb and supports
 ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
 the following software:
 
+ * ISE Webpack 9.1SP3
  * ISE Webpack 9.1SP2
  * ISE Webpack 9.1SP1
  * ISE Webpack 8.2SP3
  * ISE Webpack 8.1SP3
+ * ChipScope 9.1.03i
  * ChipScope 9.1.02i
+ * ChipScope 8.2.04i
  * EDK 8.2.02i
+ * EDK 8.1.02i
+
+In addition to the XILINX USB and parallel cables, devices based on the FTDI
+2232 serial converter chip are also experimentally supported. This includes
+devices like the Amontec JTAGkey(-Tiny).
 
 Build the library by calling `make'.
 
@@ -29,6 +37,9 @@ $ impact
 The source for this library can be found at:
 http://cvs.zerfleddert.de/cgi-bin/viewcvs.cgi/usb-driver/
 
+The main website is located at:
+http://www.rmdir.de/~michael/xilinx/
+
 
 Notes for the USB cable
 =======================
@@ -71,6 +82,11 @@ ppdev
 To use the device as an ordinary user, put the user in the group 'lp'
 
 
+If you have an almost compatible cable which works with other software but not
+with Impact, try adding -DFORCE_PC3_IDENT to the CFLAGS line in the Makefile.
+This enables a hack by Stefan Ziegenbalg to force detection of a parallel cable.
+
+
 Parallel Cable IV is currently only supported in 'compatibility mode', as no
 attempt to configure the ECP registers is done by this library.
 
@@ -81,6 +97,32 @@ HIGHZ instead of BYPASS" enabled in Edit -> Preferences -> iMPACT Configuration
 Preferences.
 If you are using batch mode, add the following line to your cmd file:
 setPreference -pref UseHighz:TRUE
-(This problem also occurs on windows and when using the real windrvr in linux and
-is solved with the same workaround. Impact 8.2 is working fine with the same
+(This problem also occurs on windows and when using the real windrvr in linux
+and is solved with the same workaround. Impact 8.2 is working fine with the same
 boards and designs)
+
+
+Notes for FTDI 2232 based cables
+================================
+
+To build the driver with FTDI 2232 support, you need to have libftdi and
+the libftdi development package installed. On debian, you can install both
+by installing 'libftdi-dev'.
+
+To set-up the device:
+1. Find out the vendor and product id of your cable using lsusb:
+   Bus 003 Device 005: ID 0403:cff8 Future Technology Devices ...
+                          ~~~~~~~~~
+
+2. Copy the sample libusb-driverrc to ~/.libusb-driverrc, edit it and replace
+   the vendor and product-id in the example file with the values from provided
+   in the lsusb-output. You can also change the 'parallel port' which is mapped
+   to this cable. Impact sees the device at that port as a Parallel Cable III.
+
+3. To use the device as an ordinary user, put the following line in a new file
+   in /etc/udev/rules.d/ and restart udev:
+   ACTION=="add", BUS=="usb", SYSFS{idVendor}=="0403", SYSFS{idProduct}=="cff8", MODE="666"
+   (replace the vendor and product id with your values)
+
+The support for FTDI 2232 based devices is experimental and they are currently
+significantly slower than the other supported cables.