update links for xc3sprog

[usb-driver] / README

diff --git a/README b/README
index 265dd3941b23edf68c967b3e3a627c1265f1caa3..f3eb7c98209c4df609e472506ae08479fa93be8a 100644 (file)
--- a/README
+++ b/README
@@ -9,6 +9,8 @@ should work on every kernel version which is supported by libusb and supports
 ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
 the following software:
 
+ * ISE 13.1
+ * ISE 12.1
  * ISE Webpack 11.1
  * ISE Webpack 10.1
  * ISE Webpack 9.2SP1, SP2, SP3, SP4
@@ -57,7 +59,7 @@ Notes for the USB cable
 
 To use the device as an ordinary user, put the following line in a new
 file "libusb-driver.rules" in /etc/udev/rules.d/ and restart udev:
-ACTION=="add", BUS=="usb", SYSFS{idVendor}=="03fd", MODE="666"
+ACTION=="add", SUBSYSTEMS=="usb", ATTRS{idVendor}=="03fd", MODE="666"
 
 
 If your cable does not have the ID 03fd:0008 in the output of lsusb,
@@ -65,15 +67,28 @@ the initial firmware has not been loaded (loading it changes the
 product-ID from another value to 8). To load the firmware follow
 these steps:
 
+1. Run ./setup_pcusb in this directory, this should set up everything
+   correctly:
+   - When $XILINX is set correctly:
+     $ ./setup_pcusb
+   - When $XILINX is not set, and ISE is installed in /opt/Xilinx/13.1:
+     $ ./setup_pcusb /opt/Xilinx/13.1/ISE_DS/ISE
+
+Old instructions, use only when the above script did not work:
+
 1. If you have no /etc/udev/rules.d/xusbdfwu.rules file, copy it from
    /path/to/ISE/bin/lin/xusbdfwu.rules to /etc/udev/rules.d/xusbdfwu.rules
 
-2. Install the package containing /sbin/fxload from your linux distribution.
+2. If you are running a newer version of udev (as in Debian Squeeze and
+   Ubuntu 9.10), you need to adapt the rules-file to the new udev-version:
+   sed -i -e 's/TEMPNODE/tempnode/' -e 's/SYSFS/ATTRS/g' -e 's/BUS/SUBSYSTEMS/' /etc/udev/rules.d/xusbdfwu.rules
+
+3. Install the package containing /sbin/fxload from your linux distribution.
    It is usually called "fxload"
 
-3. copy the files /path/to/ISE/bin/lin/xusb*.hex to /usr/share/
+4. copy the files /path/to/ISE/bin/lin/xusb*.hex to /usr/share/
 
-4. restart udev and re-plug the cable
+5. restart udev and re-plug the cable
 
 
 If you have multiple cables connected, you can specify the cable to use
@@ -140,7 +155,7 @@ To set-up the device:
 
 3. To use the device as an ordinary user, put the following line in a new file
    in /etc/udev/rules.d/ and restart udev:
-   ACTION=="add", BUS=="usb", SYSFS{idVendor}=="0403", SYSFS{idProduct}=="cff8", MODE="666"
+   ACTION=="add", SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="cff8", MODE="666"
    (replace the vendor and product id with your values)
 
 The support for FTDI 2232 based devices is experimental and they are currently