ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
the following software:
- * ISE Webpack 9.1SP3
- * ISE Webpack 9.1SP2
- * ISE Webpack 9.1SP1
+ * ISE 13.1
+ * ISE 12.1
+ * ISE Webpack 11.1
+ * ISE Webpack 10.1
+ * ISE Webpack 9.2SP1, SP2, SP3, SP4
+ * ISE Webpack 9.1SP1, SP2, SP3
* ISE Webpack 8.2SP3
* ISE Webpack 8.1SP3
- * ChipScope 9.1.03i
- * ChipScope 9.1.02i
+ * ChipScope 10.1
+ * ChipScope 9.2.01i, 9.2.02i, 9.2.03i, 9.2.04i
+ * ChipScope 9.1.02i, 9.1.03i
* ChipScope 8.2.04i
+ * EDK 10.1
+ * EDK 9.2.01i, 9.2.02i
+ * EDK 9.1.01i, 9.1.02i
* EDK 8.2.02i
* EDK 8.1.02i
+ * Synplicity Identify
In addition to the XILINX USB and parallel cables, devices based on the FTDI
2232 serial converter chip are also experimentally supported. This includes
devices like the Amontec JTAGkey(-Tiny).
-Build the library by calling `make'.
+Build the library by calling `make'. If you are on a 64 bit system but want
+to build a 32 bit library, run `make lib32' instead. Be sure to have the 32
+bit versions of libusb-devel and libftdi-devel installed!
To use this library you have to preload the library before starting impact:
The main website is located at:
http://www.rmdir.de/~michael/xilinx/
+The Git repository can be cloned with:
+git clone git://git.zerfleddert.de/usb-driver
+
Notes for the USB cable
=======================
To use the device as an ordinary user, put the following line in a new
-file in /etc/udev/rules.d/ and restart udev:
-ACTION=="add", BUS=="usb", SYSFS{idVendor}=="03fd", MODE="666"
+file "libusb-driver.rules" in /etc/udev/rules.d/ and restart udev:
+ACTION=="add", SUBSYSTEMS=="usb", ATTRS{idVendor}=="03fd", MODE="666"
If your cable does not have the ID 03fd:0008 in the output of lsusb,
product-ID from another value to 8). To load the firmware follow
these steps:
+1. Run ./setup_pcusb in this directory, this should set up everything
+ correctly:
+ - When $XILINX is set correctly:
+ $ ./setup_pcusb
+ - When $XILINX is not set, and ISE is installed in /opt/Xilinx/13.1:
+ $ ./setup_pcusb /opt/Xilinx/13.1/ISE_DS/ISE
+
+Old instructions, use only when the above script did not work:
+
1. If you have no /etc/udev/rules.d/xusbdfwu.rules file, copy it from
/path/to/ISE/bin/lin/xusbdfwu.rules to /etc/udev/rules.d/xusbdfwu.rules
-2. Install the package containing /sbin/fxload from your linux distribution.
+2. If you are running a newer version of udev (as in Debian Squeeze and
+ Ubuntu 9.10), you need to adapt the rules-file to the new udev-version:
+ sed -i -e 's/TEMPNODE/tempnode/' -e 's/SYSFS/ATTRS/g' -e 's/BUS/SUBSYSTEMS/' /etc/udev/rules.d/xusbdfwu.rules
+
+3. Install the package containing /sbin/fxload from your linux distribution.
It is usually called "fxload"
-3. copy the file /path/to/ISE/bin/lin/xusbdfwu.hex to /usr/share/xusbdfwu.hex
+4. copy the files /path/to/ISE/bin/lin/xusb*.hex to /usr/share/
+
+5. restart udev and re-plug the cable
-4. restart udev and re-plug the cable
+
+If you have multiple cables connected, you can specify the cable to use
+in the XILINX_USB_DEV environment-variable as "bus:device".
+These identifiers are available in the output of lsusb:
+Bus 001 Device 004: ID 03fd:0008 Xilinx, Inc.
+ ^^^ ^^^
+To use this cable, set the XILINX_USB_DEV variable to "001:004".
Notes for the parallel cable
3. To use the device as an ordinary user, put the following line in a new file
in /etc/udev/rules.d/ and restart udev:
- ACTION=="add", BUS=="usb", SYSFS{idVendor}=="0403", SYSFS{idProduct}=="cff8", MODE="666"
+ ACTION=="add", SUBSYSTEMS=="usb", ATTRS{idVendor}=="0403", ATTRS{idProduct}=="cff8", MODE="666"
(replace the vendor and product id with your values)
The support for FTDI 2232 based devices is experimental and they are currently
significantly slower than the other supported cables.
+
+
+Locked cables
+=============
+
+If you get the message 'The cable is being used by another application.' from
+impact, try running the following command:
+
+echo -e 'cleancablelock\nexit' | impact -batch
projects / usb-driver / blobdiff