ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
the following software:
- * ISE Webpack 9.1SP2
- * ISE Webpack 9.1SP1
+ * ISE Webpack 10.1
+ * ISE Webpack 9.2SP1, SP2, SP3, SP4
+ * ISE Webpack 9.1SP1, SP2, SP3
* ISE Webpack 8.2SP3
* ISE Webpack 8.1SP3
- * ChipScope 9.1.02i
+ * ChipScope 10.1
+ * ChipScope 9.2.01i, 9.2.02i, 9.2.03i, 9.2.04i
+ * ChipScope 9.1.02i, 9.1.03i
+ * ChipScope 8.2.04i
+ * EDK 10.1
+ * EDK 9.2.01i, 9.2.02i
+ * EDK 9.1.01i, 9.1.02i
* EDK 8.2.02i
+ * EDK 8.1.02i
+ * Synplicity Identify
-Build the library by calling `make'.
+In addition to the XILINX USB and parallel cables, devices based on the FTDI
+2232 serial converter chip are also experimentally supported. This includes
+devices like the Amontec JTAGkey(-Tiny).
+
+Build the library by calling `make'. If you are on a 64 bit system but want
+to build a 32 bit library, run `make lib32' instead.
To use this library you have to preload the library before starting impact:
$ setenv LD_PRELOAD /path/to/libusb-driver.so (for csh shells)
$ impact
+The source for this library can be found at:
+http://git.zerfleddert.de/cgi-bin/gitweb.cgi/usb-driver
+
+The main website is located at:
+http://www.rmdir.de/~michael/xilinx/
+
+The Git repository can be cloned with:
+git clone git://git.zerfleddert.de/usb-driver
+
Notes for the USB cable
=======================
To use the device as an ordinary user, put the following line in a new
-file in /etc/udev/rules.d/ and restart udev:
+file "libusb-driver.rules" in /etc/udev/rules.d/ and restart udev:
ACTION=="add", BUS=="usb", SYSFS{idVendor}=="03fd", MODE="666"
2. Install the package containing /sbin/fxload from your linux distribution.
It is usually called "fxload"
-3. copy the file /path/to/ISE/bin/lin/xusbdfwu.hex to /usr/share/xusbdfwu.hex
+3. copy the files /path/to/ISE/bin/lin/xusb*.hex to /usr/share/
4. restart udev and re-plug the cable
+If you have multiple cables connected, you can specify the cable to use
+in the XILINX_USB_DEV environment-variable as "bus:device".
+These identifiers are available in the output of lsusb:
+Bus 001 Device 004: ID 03fd:0008 Xilinx, Inc.
+ ^^^ ^^^
+To use this cable, set the XILINX_USB_DEV variable to "001:004".
+
+
Notes for the parallel cable
============================
To use the device as an ordinary user, put the user in the group 'lp'
+If you have an almost compatible cable which works with other software but not
+with Impact, try adding -DFORCE_PC3_IDENT to the CFLAGS line in the Makefile.
+This enables a hack by Stefan Ziegenbalg to force detection of a parallel cable.
+
+
Parallel Cable IV is currently only supported in 'compatibility mode', as no
attempt to configure the ECP registers is done by this library.
+
+
+If you get "Programming failed" or "DONE did not go high" when programming
+through the parallel cable with Impact 9.1, make sure to have the option "Use
+HIGHZ instead of BYPASS" enabled in Edit -> Preferences -> iMPACT Configuration
+Preferences.
+If you are using batch mode, add the following line to your cmd file:
+setPreference -pref UseHighz:TRUE
+(This problem also occurs on windows and when using the real windrvr in linux
+and is solved with the same workaround. Impact 8.2 is working fine with the same
+boards and designs)
+
+
+Notes for FTDI 2232 based cables
+================================
+
+To build the driver with FTDI 2232 support, you need to have libftdi and
+the libftdi development package installed. On debian, you can install both
+by installing 'libftdi-dev'.
+
+To set-up the device:
+1. Find out the vendor and product id of your cable using lsusb:
+ Bus 003 Device 005: ID 0403:cff8 Future Technology Devices ...
+ ~~~~~~~~~
+
+2. Copy the sample libusb-driverrc to ~/.libusb-driverrc, edit it and replace
+ the vendor and product-id in the example file with the values provided in
+ the lsusb-output. You can also change the 'parallel port' which is mapped to
+ this cable. Impact sees the device at that port as a Parallel Cable III.
+
+3. To use the device as an ordinary user, put the following line in a new file
+ in /etc/udev/rules.d/ and restart udev:
+ ACTION=="add", BUS=="usb", SYSFS{idVendor}=="0403", SYSFS{idProduct}=="cff8", MODE="666"
+ (replace the vendor and product id with your values)
+
+The support for FTDI 2232 based devices is experimental and they are currently
+significantly slower than the other supported cables.
+
+
+Locked cables
+=============
+
+If you get the message 'The cable is being used by another application.' from
+impact, try running the following command:
+
+echo -e 'cleancablelock\nexit' | impact -batch
projects / usb-driver / blobdiff