typo

[usb-driver] / README

diff --git a/README b/README
index 13737b53039f8a816b70561d28ea0a20ea8518fa..bf32f6a4bb6f615d11cf86e92218f6254653bf3f 100644 (file)
--- a/README
+++ b/README
@@ -14,8 +14,15 @@ the following software:
  * ISE Webpack 9.1SP1
  * ISE Webpack 8.2SP3
  * ISE Webpack 8.1SP3
  * ISE Webpack 9.1SP1
  * ISE Webpack 8.2SP3
  * ISE Webpack 8.1SP3

+ * ChipScope 9.1.03i

  * ChipScope 9.1.02i
  * ChipScope 9.1.02i

+ * ChipScope 8.2.04i

  * EDK 8.2.02i
  * EDK 8.2.02i

+ * EDK 8.1.02i
+
+In addition to the XILINX USB and parallel cables, devices based on the FTDI
+2232 serial converter chip are also experimentally supported. This includes
+devices like the Amontec JTAGkey(-Tiny).

 
 Build the library by calling `make'.
 
 
 Build the library by calling `make'.
 


@@ -30,6 +37,9 @@ $ impact
 The source for this library can be found at:
 http://cvs.zerfleddert.de/cgi-bin/viewcvs.cgi/usb-driver/
 
 The source for this library can be found at:
 http://cvs.zerfleddert.de/cgi-bin/viewcvs.cgi/usb-driver/
 

+The main website is located at:
+http://www.rmdir.de/~michael/xilinx/
+

 
 Notes for the USB cable
 =======================
 
 Notes for the USB cable
 =======================


@@ -72,6 +82,11 @@ ppdev
 To use the device as an ordinary user, put the user in the group 'lp'
 
 
 To use the device as an ordinary user, put the user in the group 'lp'
 
 

+If you have an almost compatible cable which works with other software but not
+with Impact, try adding -DFORCE_PC3_IDENT to the CFLAGS line in the Makefile.
+This enables a hack by Stefan Ziegenbalg to force detection of a parallel cable.
+
+

 Parallel Cable IV is currently only supported in 'compatibility mode', as no
 attempt to configure the ECP registers is done by this library.
 
 Parallel Cable IV is currently only supported in 'compatibility mode', as no
 attempt to configure the ECP registers is done by this library.
 


@@ -82,6 +97,32 @@ HIGHZ instead of BYPASS" enabled in Edit -> Preferences -> iMPACT Configuration
 Preferences.
 If you are using batch mode, add the following line to your cmd file:
 setPreference -pref UseHighz:TRUE
 Preferences.
 If you are using batch mode, add the following line to your cmd file:
 setPreference -pref UseHighz:TRUE

-(This problem also occurs on windows and when using the real windrvr in linux and
-is solved with the same workaround. Impact 8.2 is working fine with the same
+(This problem also occurs on windows and when using the real windrvr in linux
+and is solved with the same workaround. Impact 8.2 is working fine with the same

 boards and designs)
 boards and designs)

+
+
+Notes for FTDI 2232 based cables
+================================
+
+To build the driver with FTDI 2232 support, you need to have libftdi and
+the libftdi development package installed. On debian, you can install both
+by installing 'libftdi-dev'.
+
+To set-up the device:
+1. Find out the vendor and product id of your cable using lsusb:
+   Bus 003 Device 005: ID 0403:cff8 Future Technology Devices ...
+                          ~~~~~~~~~
+
+2. Copy the sample libusb-driverrc to ~/.libusb-driverrc, edit it and replace
+   the vendor and product-id in the example file with the values from provided
+   in the lsusb-output. You can also change the 'parallel port' which is mapped
+   to this cable. Impact sees the device at that port as a Parallel Cable III.
+
+3. To use the device as an ordinary user, put the following line in a new file
+   in /etc/udev/rules.d/ and restart udev:
+   ACTION=="add", BUS=="usb", SYSFS{idVendor}=="0403", SYSFS{idProduct}=="cff8", MODE="666"
+   (replace the vendor and product id with your values)
+
+The support for FTDI 2232 based devices is experimental and they are currently
+significantly slowen than the other supported cables.