]> git.zerfleddert.de Git - proxmark3-svn/blob - fpga/hi_simulate.v
Revert "Comms refactor (prerequisite of libproxmark work) (#371)"
[proxmark3-svn] / fpga / hi_simulate.v
1 //-----------------------------------------------------------------------------
2 // Pretend to be an ISO 14443 tag. We will do this by alternately short-
3 // circuiting and open-circuiting the antenna coil, with the tri-state
4 // pins.
5 //
6 // We communicate over the SSP, as a bitstream (i.e., might as well be
7 // unframed, though we still generate the word sync signal). The output
8 // (ARM -> FPGA) tells us whether to modulate or not. The input (FPGA
9 // -> ARM) is us using the A/D as a fancy comparator; this is with
10 // (software-added) hysteresis, to undo the high-pass filter.
11 //
12 // At this point only Type A is implemented. This means that we are using a
13 // bit rate of 106 kbit/s, or fc/128. Oversample by 4, which ought to make
14 // things practical for the ARM (fc/32, 423.8 kbits/s, ~50 kbytes/s)
15 //
16 // Jonathan Westhues, October 2006
17 //-----------------------------------------------------------------------------
18
19 module hi_simulate(
20 pck0, ck_1356meg, ck_1356megb,
21 pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
22 adc_d, adc_clk,
23 ssp_frame, ssp_din, ssp_dout, ssp_clk,
24 cross_hi, cross_lo,
25 dbg,
26 mod_type
27 );
28 input pck0, ck_1356meg, ck_1356megb;
29 output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
30 input [7:0] adc_d;
31 output adc_clk;
32 input ssp_dout;
33 output ssp_frame, ssp_din, ssp_clk;
34 input cross_hi, cross_lo;
35 output dbg;
36 input [2:0] mod_type;
37
38 // Power amp goes between LOW and tri-state, so pwr_hi (and pwr_lo) can
39 // always be low.
40 assign pwr_hi = 1'b0;
41 assign pwr_lo = 1'b0;
42
43 // The comparator with hysteresis on the output from the peak detector.
44 reg after_hysteresis;
45 assign adc_clk = ck_1356meg;
46
47 always @(negedge adc_clk)
48 begin
49 if(& adc_d[7:5]) after_hysteresis = 1'b1;
50 else if(~(| adc_d[7:5])) after_hysteresis = 1'b0;
51 end
52
53
54 // Divide 13.56 MHz by 32 to produce the SSP_CLK
55 // The register is bigger to allow higher division factors of up to /128
56 reg [10:0] ssp_clk_divider;
57
58 always @(posedge adc_clk)
59 ssp_clk_divider <= (ssp_clk_divider + 1);
60
61 reg ssp_clk;
62 reg ssp_frame;
63 always @(negedge adc_clk)
64 begin
65 //If we're in 101, we only need a new bit every 8th carrier bit (53Hz). Otherwise, get next bit at 424Khz
66 if(mod_type == 3'b101)
67 begin
68 if(ssp_clk_divider[7:0] == 8'b00000000)
69 ssp_clk <= 1'b0;
70 if(ssp_clk_divider[7:0] == 8'b10000000)
71 ssp_clk <= 1'b1;
72
73 end
74 else
75 begin
76 if(ssp_clk_divider[4:0] == 5'd0)//[4:0] == 5'b00000)
77 ssp_clk <= 1'b1;
78 if(ssp_clk_divider[4:0] == 5'd16) //[4:0] == 5'b10000)
79 ssp_clk <= 1'b0;
80 end
81 end
82
83
84 //assign ssp_clk = ssp_clk_divider[4];
85
86 // Divide SSP_CLK by 8 to produce the byte framing signal; the phase of
87 // this is arbitrary, because it's just a bitstream.
88 // One nasty issue, though: I can't make it work with both rx and tx at
89 // once. The phase wrt ssp_clk must be changed. TODO to find out why
90 // that is and make a better fix.
91 reg [2:0] ssp_frame_divider_to_arm;
92 always @(posedge ssp_clk)
93 ssp_frame_divider_to_arm <= (ssp_frame_divider_to_arm + 1);
94 reg [2:0] ssp_frame_divider_from_arm;
95 always @(negedge ssp_clk)
96 ssp_frame_divider_from_arm <= (ssp_frame_divider_from_arm + 1);
97
98
99
100 always @(ssp_frame_divider_to_arm or ssp_frame_divider_from_arm or mod_type)
101 if(mod_type == 3'b000) // not modulating, so listening, to ARM
102 ssp_frame = (ssp_frame_divider_to_arm == 3'b000);
103 else
104 ssp_frame = (ssp_frame_divider_from_arm == 3'b000);
105
106 // Synchronize up the after-hysteresis signal, to produce DIN.
107 reg ssp_din;
108 always @(posedge ssp_clk)
109 ssp_din = after_hysteresis;
110
111 // Modulating carrier frequency is fc/16, reuse ssp_clk divider for that
112 reg modulating_carrier;
113 always @(mod_type or ssp_clk or ssp_dout)
114 if(mod_type == 3'b000)
115 modulating_carrier <= 1'b0; // no modulation
116 else if(mod_type == 3'b001)
117 modulating_carrier <= ssp_dout ^ ssp_clk_divider[3]; // XOR means BPSK
118 else if(mod_type == 3'b010)
119 modulating_carrier <= ssp_dout & ssp_clk_divider[5]; // switch 212kHz subcarrier on/off
120 else if(mod_type == 3'b100 || mod_type == 3'b101)
121 modulating_carrier <= ssp_dout & ssp_clk_divider[4]; // switch 424kHz modulation on/off
122 else
123 modulating_carrier <= 1'b0; // yet unused
124
125 // This one is all LF, so doesn't matter
126 assign pwr_oe2 = modulating_carrier;
127
128 // Toggle only one of these, since we are already producing much deeper
129 // modulation than a real tag would.
130 assign pwr_oe1 = modulating_carrier;
131 assign pwr_oe4 = modulating_carrier;
132
133 // This one is always on, so that we can watch the carrier.
134 assign pwr_oe3 = 1'b0;
135
136 assign dbg = modulating_carrier;
137 //reg dbg;
138 //always @(ssp_dout)
139 // dbg <= ssp_dout;
140
141 endmodule
Impressum, Datenschutz