git.zerfleddert.de Git - proxmark3-svn/blob - fpga/hi_iso14443a.v

   1 //-----------------------------------------------------------------------------
   2 // ISO14443-A support for the Proxmark III
   3 // Gerhard de Koning Gans, April 2008
   4 //-----------------------------------------------------------------------------
   5
   6 // constants for the different modes:
   7 `define SNIFFER                 3'b000
   8 `define TAGSIM_LISTEN   3'b001
   9 `define TAGSIM_MOD              3'b010
  10 `define READER_LISTEN   3'b011
  11 `define READER_MOD              3'b100
  12
  13 module hi_iso14443a(
  14     pck0, ck_1356meg, ck_1356megb,
  15     pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4,
  16     adc_d, adc_clk,
  17     ssp_frame, ssp_din, ssp_dout, ssp_clk,
  18     cross_hi, cross_lo,
  19     dbg,
  20     mod_type
  21 );
  22     input pck0, ck_1356meg, ck_1356megb;
  23     output pwr_lo, pwr_hi, pwr_oe1, pwr_oe2, pwr_oe3, pwr_oe4;
  24     input [7:0] adc_d;
  25     output adc_clk;
  26     input ssp_dout;
  27     output ssp_frame, ssp_din, ssp_clk;
  28     input cross_hi, cross_lo;
  29     output dbg;
  30     input [2:0] mod_type;
  31
  32
  33 wire adc_clk = ck_1356meg;
  34
  35
  36
  37 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
  38 // Reader -> PM3:
  39 // detecting and shaping the reader's signal. Reader will modulate the carrier by 100% (signal is either on or off). Use a
  40 // hysteresis (Schmitt Trigger) to avoid false triggers during slowly increasing or decreasing carrier amplitudes
  41 reg after_hysteresis;
  42 reg [11:0] has_been_low_for;
  43
  44 always @(negedge adc_clk)
  45 begin
  46         if(adc_d >= 16) after_hysteresis <= 1'b1;                       // U >= 1,14V   -> after_hysteresis = 1
  47     else if(adc_d < 8) after_hysteresis <= 1'b0;                // U <  1,04V   -> after_hysteresis = 0
  48         // Note: was >= 3,53V and <= 1,19V. The new trigger values allow more reliable detection of the first bit
  49         // (it might not reach 3,53V due to the high time constant of the high pass filter in the analogue RF part).
  50         // In addition, the new values are more in line with ISO14443-2: "The PICC shall detect the ”End of Pause” after the field exceeds
  51         // 5% of H_INITIAL and before it exceeds 60% of H_INITIAL." Depending on the signal strength, 60% might well be less than 3,53V.
  52
  53
  54         // detecting a loss of reader's field (adc_d < 192 for 4096 clock cycles). If this is the case,
  55         // set the detected reader signal (after_hysteresis) to '1' (unmodulated)
  56         if(adc_d >= 192)
  57     begin
  58         has_been_low_for <= 12'd0;
  59     end
  60     else
  61     begin
  62         if(has_been_low_for == 12'd4095)
  63         begin
  64             has_been_low_for <= 12'd0;
  65             after_hysteresis <= 1'b1;
  66         end
  67         else
  68                 begin
  69             has_been_low_for <= has_been_low_for + 1;
  70                 end
  71     end
  72
  73 end
  74
  75
  76
  77 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
  78 // Reader -> PM3
  79 // detect when a reader is active (modulating). We assume that the reader is active, if we see the carrier off for at least 8
  80 // carrier cycles. We assume that the reader is inactive, if the carrier stayed high for at least 256 carrier cycles.
  81 reg deep_modulation;
  82 reg [2:0] deep_counter;
  83 reg [8:0] saw_deep_modulation;
  84
  85 always @(negedge adc_clk)
  86 begin
  87         if(~(| adc_d[7:0]))                                                                     // if adc_d == 0 (U <= 0,94V)
  88         begin
  89                 if(deep_counter == 3'd7)                                                // adc_d == 0 for 8 adc_clk ticks -> deep_modulation (by reader)
  90                 begin
  91                         deep_modulation <= 1'b1;
  92                         saw_deep_modulation <= 8'd0;
  93                 end
  94                 else
  95                         deep_counter <= deep_counter + 1;
  96         end
  97         else
  98         begin
  99                 deep_counter <= 3'd0;
 100                 if(saw_deep_modulation == 8'd255)                               // adc_d != 0 for 256 adc_clk ticks -> deep_modulation is over, probably waiting for tag's response
 101                         deep_modulation <= 1'b0;
 102                 else
 103                         saw_deep_modulation <= saw_deep_modulation + 1;
 104         end
 105 end
 106
 107
 108
 109 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 110 // Tag -> PM3
 111 // filter the input for a tag's signal. The filter box needs the 4 previous input values and is a gaussian derivative filter
 112 // for noise reduction and edge detection.
 113 // store 4 previous samples:
 114 reg [7:0] input_prev_4, input_prev_3, input_prev_2, input_prev_1;
 115
 116 always @(negedge adc_clk)
 117 begin
 118         input_prev_4 <= input_prev_3;
 119         input_prev_3 <= input_prev_2;
 120         input_prev_2 <= input_prev_1;
 121         input_prev_1 <= adc_d;
 122 end
 123
 124 // adc_d_filtered = 2*input_prev4 + 1*input_prev3 + 0*input_prev2 - 1*input_prev1 - 2*input
 125 //                                      = (2*input_prev4 + input_prev3) - (2*input + input_prev1)
 126 wire [8:0] input_prev_4_times_2 = input_prev_4 << 1;
 127 wire [8:0] adc_d_times_2                = adc_d << 1;
 128
 129 wire [9:0] tmp1 = input_prev_4_times_2 + input_prev_3;
 130 wire [9:0] tmp2 = adc_d_times_2 + input_prev_1;
 131
 132 // convert intermediate signals to signed and calculate the filter output
 133 wire signed [10:0] adc_d_filtered = {1'b0, tmp1} - {1'b0, tmp2};
 134
 135
 136
 137 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 138 // internal FPGA timing. Maximum required period is 128 carrier clock cycles for a full 8 Bit transfer to ARM. (i.e. we need a
 139 // 7 bit counter). Adjust its frequency to external reader's clock when simulating a tag or sniffing.
 140 reg pre_after_hysteresis;
 141 reg [3:0] reader_falling_edge_time;
 142 reg [6:0] negedge_cnt;
 143
 144 always @(negedge adc_clk)
 145 begin
 146         // detect a reader signal's falling edge and remember its timing:
 147         pre_after_hysteresis <= after_hysteresis;
 148         if (pre_after_hysteresis && ~after_hysteresis)
 149         begin
 150                 reader_falling_edge_time[3:0] <= negedge_cnt[3:0];
 151         end
 152
 153         // adjust internal timer counter if necessary:
 154         if (negedge_cnt[3:0] == 4'd13 && (mod_type == `SNIFFER || mod_type == `TAGSIM_LISTEN) && deep_modulation)
 155         begin
 156                 if (reader_falling_edge_time == 4'd1)                   // reader signal changes right after sampling. Better sample earlier next time.
 157                 begin
 158                         negedge_cnt <= negedge_cnt + 2;                         // time warp
 159                 end
 160                 else if (reader_falling_edge_time == 4'd0)              // reader signal changes right before sampling. Better sample later next time.
 161                 begin
 162                         negedge_cnt <= negedge_cnt;                                     // freeze time
 163                 end
 164                 else
 165                 begin
 166                         negedge_cnt <= negedge_cnt + 1;                         // Continue as usual
 167                 end
 168                 reader_falling_edge_time[3:0] <= 4'd8;                  // adjust only once per detected edge
 169         end
 170         else if (negedge_cnt == 7'd127)                                         // normal operation: count from 0 to 127
 171         begin
 172                 negedge_cnt <= 0;
 173         end
 174         else
 175         begin
 176                 negedge_cnt <= negedge_cnt + 1;
 177         end
 178 end
 179
 180
 181 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 182 // Tag -> PM3:
 183 // determine best possible time for starting/resetting the modulation detector.
 184 reg [3:0] mod_detect_reset_time;
 185
 186 always @(negedge adc_clk)
 187 begin
 188         if (mod_type == `READER_LISTEN)
 189         // (our) reader signal changes at negedge_cnt[3:0]=9, tag response expected to start n*16+4 ticks later, further delayed by
 190         // 3 ticks ADC conversion. The maximum filter output (edge detected) will be detected after subcarrier zero crossing (+7 ticks).
 191         // To allow some timing variances, we want to have the maximum filter outputs well within the detection window, i.e.
 192         // at mod_detect_reset_time+4 and mod_detect_reset_time+12  (-4 ticks).
 193         // 9 + 4 + 3 + 7 - 4  = 19.    19 mod 16 = 3
 194         begin
 195                 mod_detect_reset_time <= 4'd4;
 196         end
 197         else
 198         if (mod_type == `SNIFFER)
 199         begin
 200                 // detect a rising edge of reader's signal and sync modulation detector to the tag's answer:
 201                 if (~pre_after_hysteresis && after_hysteresis && deep_modulation)
 202                 // reader signal rising edge detected at negedge_cnt[3:0]. This signal had been delayed
 203                 // 9 ticks by the RF part + 3 ticks by the A/D converter + 1 tick to assign to after_hysteresis.
 204                 // Then the same as above.
 205                 // - 9 - 3 - 1 + 4 + 3 + 7 - 4 = -3
 206                 begin
 207                         mod_detect_reset_time <= negedge_cnt[3:0] - 4'd3;
 208                 end
 209         end
 210 end
 211
 212
 213 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 214 // Tag -> PM3:
 215 // modulation detector. Looks for the steepest falling and rising edges within a 16 clock period. If there is both a significant
 216 // falling and rising edge (in any order), a modulation is detected.
 217 reg signed [10:0] rx_mod_falling_edge_max;
 218 reg signed [10:0] rx_mod_rising_edge_max;
 219 reg curbit;
 220
 221 `define EDGE_DETECT_THRESHOLD   5
 222
 223 always @(negedge adc_clk)
 224 begin
 225         if(negedge_cnt[3:0] == mod_detect_reset_time)
 226         begin
 227                 // detect modulation signal: if modulating, there must have been a falling AND a rising edge
 228                 if ((rx_mod_falling_edge_max > `EDGE_DETECT_THRESHOLD) && (rx_mod_rising_edge_max < -`EDGE_DETECT_THRESHOLD))
 229                                 curbit <= 1'b1; // modulation
 230                         else
 231                                 curbit <= 1'b0; // no modulation
 232                 // reset modulation detector
 233                 rx_mod_rising_edge_max <= 0;
 234                 rx_mod_falling_edge_max <= 0;
 235         end
 236         else                                                                                    // look for steepest edges (slopes)
 237         begin
 238                 if (adc_d_filtered > 0)
 239                 begin
 240                         if (adc_d_filtered > rx_mod_falling_edge_max)
 241                                 rx_mod_falling_edge_max <= adc_d_filtered;
 242                 end
 243                 else
 244                 begin
 245                         if (adc_d_filtered < rx_mod_rising_edge_max)
 246                                 rx_mod_rising_edge_max <= adc_d_filtered;
 247                 end
 248         end
 249
 250 end
 251
 252
 253
 254 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 255 // Tag+Reader -> PM3
 256 // sample 4 bits reader data and 4 bits tag data for sniffing
 257 reg [3:0] reader_data;
 258 reg [3:0] tag_data;
 259
 260 always @(negedge adc_clk)
 261 begin
 262     if(negedge_cnt[3:0] == 4'd0)
 263         begin
 264         reader_data[3:0] <= {reader_data[2:0], after_hysteresis};
 265                 tag_data[3:0] <= {tag_data[2:0], curbit};
 266         end
 267 end
 268
 269
 270
 271 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 272 // PM3 -> Reader:
 273 // a delay line to ensure that we send the (emulated) tag's answer at the correct time according to ISO14443-3
 274 reg [31:0] mod_sig_buf;
 275 reg [4:0] mod_sig_ptr;
 276 reg mod_sig;
 277
 278 always @(negedge adc_clk)
 279 begin
 280         if(negedge_cnt[3:0] == 4'd0)    // sample data at rising edge of ssp_clk - ssp_dout changes at the falling edge.
 281         begin
 282                 mod_sig_buf[31:2] <= mod_sig_buf[30:1];                         // shift
 283                 if (~ssp_dout && ~mod_sig_buf[1])
 284                         mod_sig_buf[1] <= 1'b0;                                                 // delete the correction bit (a single 1 preceded and succeeded by 0)
 285                 else
 286                         mod_sig_buf[1] <= mod_sig_buf[0];
 287                 mod_sig_buf[0] <= ssp_dout;                                                     // add new data to the delay line
 288
 289                 mod_sig = mod_sig_buf[mod_sig_ptr];                                     // the delayed signal.
 290         end
 291 end
 292
 293
 294
 295 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 296 // PM3 -> Reader, internal timing:
 297 // a timer for the 1172 cycles fdt (Frame Delay Time). Start the timer with a rising edge of the reader's signal.
 298 // set fdt_elapsed when we no longer need to delay data. Set fdt_indicator when we can start sending data.
 299 // Note: the FPGA only takes care for the 1172 delay. To achieve an additional 1236-1172=64 ticks delay, the ARM must send
 300 // a correction bit (before the start bit). The correction bit will be coded as 00010000, i.e. it adds 4 bits to the
 301 // transmission stream, causing the required additional delay.
 302 reg [10:0] fdt_counter;
 303 reg fdt_indicator, fdt_elapsed;
 304 reg [3:0] mod_sig_flip;
 305 reg [3:0] sub_carrier_cnt;
 306
 307 // we want to achieve a delay of 1172. The RF part already has delayed the reader signals's rising edge
 308 // by 9 ticks, the ADC took 3 ticks and there is always a delay of 32 ticks by the mod_sig_buf. Therefore need to
 309 // count to 1172 - 9 - 3 - 32 = 1128
 310 `define FDT_COUNT 11'd1128
 311
 312 // The ARM must not send too early, otherwise the mod_sig_buf will overflow, therefore signal that we are ready
 313 // with fdt_indicator. The mod_sig_buf can buffer 29 excess data bits, i.e. a maximum delay of 29 * 16 = 464 adc_clk ticks.
 314 // fdt_indicator could appear at ssp_din after 1 tick, the transfer needs 16 ticks, the ARM can send 128 ticks later.
 315 // 1128 - 464 - 1 - 128 - 8 = 535
 316 `define FDT_INDICATOR_COUNT 11'd535
 317
 318 // reset on a pause in listen mode. I.e. the counter starts when the pause is over:
 319 assign fdt_reset = ~after_hysteresis && mod_type == `TAGSIM_LISTEN;
 320
 321 always @(negedge adc_clk)
 322 begin
 323         if (fdt_reset)
 324         begin
 325                 fdt_counter <= 11'd0;
 326                 fdt_elapsed <= 1'b0;
 327                 fdt_indicator <= 1'b0;
 328         end
 329         else
 330         begin
 331                 if(fdt_counter == `FDT_COUNT)
 332                 begin
 333                         if(~fdt_elapsed)                                                        // just reached fdt.
 334                         begin
 335                                 mod_sig_flip <= negedge_cnt[3:0];               // start modulation at this time
 336                                 sub_carrier_cnt <= 4'd0;                                // subcarrier phase in sync with start of modulation
 337                                 fdt_elapsed <= 1'b1;
 338                         end
 339                         else
 340                         begin
 341                                 sub_carrier_cnt <= sub_carrier_cnt + 1;
 342                         end
 343                 end
 344                 else
 345                 begin
 346                         fdt_counter <= fdt_counter + 1;
 347                 end
 348         end
 349
 350         if(fdt_counter == `FDT_INDICATOR_COUNT) fdt_indicator <= 1'b1;
 351 end
 352
 353
 354 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 355 // PM3 -> Reader or Tag
 356 // assign a modulation signal to the antenna. This signal is either a delayed signal (to achieve fdt when sending to a reader)
 357 // or undelayed when sending to a tag
 358 reg mod_sig_coil;
 359
 360 always @(negedge adc_clk)
 361 begin
 362         if (mod_type == `TAGSIM_MOD)                     // need to take care of proper fdt timing
 363         begin
 364                 if(fdt_counter == `FDT_COUNT)
 365                 begin
 366                         if(fdt_elapsed)
 367                         begin
 368                                 if(negedge_cnt[3:0] == mod_sig_flip) mod_sig_coil <= mod_sig;
 369                         end
 370                         else
 371                         begin
 372                                 mod_sig_coil <= mod_sig;        // just reached fdt. Immediately assign signal to coil
 373                         end
 374                 end
 375         end
 376         else                                                                    // other modes: don't delay
 377         begin
 378                 mod_sig_coil <= ssp_dout;
 379         end
 380 end
 381
 382
 383
 384 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 385 // PM3 -> Reader
 386 // determine the required delay in the mod_sig_buf (set mod_sig_ptr).
 387 reg temp_buffer_reset;
 388
 389 always @(negedge adc_clk)
 390 begin
 391         if(fdt_reset)
 392         begin
 393                 mod_sig_ptr <= 5'd0;
 394                 temp_buffer_reset = 1'b0;
 395         end
 396         else
 397         begin
 398                 if(fdt_counter == `FDT_COUNT && ~fdt_elapsed)                                                   // if we just reached fdt
 399                         if(~(| mod_sig_ptr[4:0]))
 400                                 mod_sig_ptr <= 5'd8;                                                                                    // ... but didn't buffer a 1 yet, delay next 1 by n*128 ticks.
 401                         else
 402                                 temp_buffer_reset = 1'b1;                                                                               // else no need for further delays.
 403
 404                 if(negedge_cnt[3:0] == 4'd0)                                                                                    // at rising edge of ssp_clk - ssp_dout changes at the falling edge.
 405                 begin
 406                         if((ssp_dout || (| mod_sig_ptr[4:0])) && ~fdt_elapsed)                          // buffer a 1 (and all subsequent data) until fdt is reached.
 407                                 if (mod_sig_ptr == 5'd31)
 408                                         mod_sig_ptr <= 5'd0;                                                                            // buffer overflow - data loss.
 409                                 else
 410                                         mod_sig_ptr <= mod_sig_ptr + 1;                                                         // increase buffer (= increase delay by 16 adc_clk ticks). mod_sig_ptr always points ahead of first 1.
 411                         else if(fdt_elapsed && ~temp_buffer_reset)
 412                         begin
 413                                 // wait for the next 1 after fdt_elapsed before fixing the delay and starting modulation. This ensures that the response can only happen
 414                                 // at intervals of 8 * 16 = 128 adc_clk ticks (as defined in ISO14443-3)
 415                                 if(ssp_dout)
 416                                         temp_buffer_reset = 1'b1;
 417                                 if(mod_sig_ptr == 5'd1)
 418                                         mod_sig_ptr <= 5'd8;                                                                            // still nothing received, need to go for the next interval
 419                                 else
 420                                         mod_sig_ptr <= mod_sig_ptr - 1;                                                         // decrease buffer.
 421                         end
 422                 end
 423         end
 424 end
 425
 426
 427
 428 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 429 // FPGA -> ARM communication:
 430 // buffer 8 bits data to be sent to ARM. Shift them out bit by bit.
 431 reg [7:0] to_arm;
 432
 433 always @(negedge adc_clk)
 434 begin
 435         if (negedge_cnt[5:0] == 6'd63)                                                  // fill the buffer
 436         begin
 437                 if (mod_type == `SNIFFER)
 438                 begin
 439                         if(deep_modulation)                                                     // a reader is sending (or there's no field at all)
 440                         begin
 441                                 to_arm <= {reader_data[3:0], 4'b0000};          // don't send tag data
 442                         end
 443                         else
 444                         begin
 445                                 to_arm <= {reader_data[3:0], tag_data[3:0]};
 446                         end
 447                 end
 448                 else
 449                 begin
 450                         to_arm[7:0] <= {mod_sig_ptr[4:0], mod_sig_flip[3:1]}; // feedback timing information
 451                 end
 452         end
 453
 454         if(negedge_cnt[2:0] == 3'b000 && mod_type == `SNIFFER)  // shift at double speed
 455         begin
 456                 // Don't shift if we just loaded new data, obviously.
 457                 if(negedge_cnt[5:0] != 6'd0)
 458                 begin
 459                         to_arm[7:1] <= to_arm[6:0];
 460                 end
 461         end
 462
 463         if(negedge_cnt[3:0] == 4'b0000 && mod_type != `SNIFFER)
 464         begin
 465                 // Don't shift if we just loaded new data, obviously.
 466                 if(negedge_cnt[6:0] != 7'd0)
 467                 begin
 468                         to_arm[7:1] <= to_arm[6:0];
 469                 end
 470         end
 471
 472 end
 473
 474
 475 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 476 // FPGA <-> ARM communication:
 477 // generate a ssp clock and ssp frame signal for the synchronous transfer from/to the ARM
 478 reg ssp_clk;
 479 reg ssp_frame;
 480
 481 always @(negedge adc_clk)
 482 begin
 483         if(mod_type == `SNIFFER)
 484         // SNIFFER mode (ssp_clk = adc_clk / 8, ssp_frame clock = adc_clk / 64)):
 485         begin
 486                 if(negedge_cnt[2:0] == 3'd0)
 487                         ssp_clk <= 1'b1;
 488                 if(negedge_cnt[2:0] == 3'd4)
 489                         ssp_clk <= 1'b0;
 490
 491                 if(negedge_cnt[5:0] == 6'd0)    // ssp_frame rising edge indicates start of frame
 492                         ssp_frame <= 1'b1;
 493                 if(negedge_cnt[5:0] == 6'd8)
 494                         ssp_frame <= 1'b0;
 495         end
 496         else
 497         // all other modes (ssp_clk = adc_clk / 16, ssp_frame clock = adc_clk / 128):
 498         begin
 499                 if(negedge_cnt[3:0] == 4'd0)
 500                         ssp_clk <= 1'b1;
 501                 if(negedge_cnt[3:0] == 4'd8)
 502                         ssp_clk <= 1'b0;
 503
 504                 if(negedge_cnt[6:0] == 7'd7)    // ssp_frame rising edge indicates start of frame
 505                         ssp_frame <= 1'b1;
 506                 if(negedge_cnt[6:0] == 7'd23)
 507                         ssp_frame <= 1'b0;
 508         end
 509 end
 510
 511
 512
 513 ////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
 514 // FPGA -> ARM communication:
 515 // select the data to be sent to ARM
 516 reg bit_to_arm;
 517 reg sendbit;
 518
 519 always @(negedge adc_clk)
 520 begin
 521         if(negedge_cnt[3:0] == 4'd0)
 522         begin
 523                 // What do we communicate to the ARM
 524                 if(mod_type == `TAGSIM_LISTEN)
 525                         sendbit = after_hysteresis;
 526                 else if(mod_type == `TAGSIM_MOD)
 527                         /* if(fdt_counter > 11'd772) sendbit = mod_sig_coil; // huh?
 528                         else */
 529                         sendbit = fdt_indicator;
 530                 else if (mod_type == `READER_LISTEN)
 531                         sendbit = curbit;
 532                 else
 533                         sendbit = 1'b0;
 534         end
 535
 536
 537         if(mod_type == `SNIFFER)
 538                 // send sampled reader and tag data:
 539                 bit_to_arm = to_arm[7];
 540         else if (mod_type == `TAGSIM_MOD && fdt_elapsed && temp_buffer_reset)
 541                 // send timing information:
 542                 bit_to_arm = to_arm[7];
 543         else
 544                 // send data or fdt_indicator
 545                 bit_to_arm = sendbit;
 546 end
 547
 548
 549
 550
 551 assign ssp_din = bit_to_arm;
 552
 553 // Subcarrier (adc_clk/16, for TAGSIM_MOD only).
 554 wire sub_carrier;
 555 assign sub_carrier = ~sub_carrier_cnt[3];
 556
 557 // in READER_MOD: drop carrier for mod_sig_coil==1 (pause); in READER_LISTEN: carrier always on; in other modes: carrier always off
 558 assign pwr_hi = (ck_1356megb & (((mod_type == `READER_MOD) & ~mod_sig_coil) || (mod_type == `READER_LISTEN)));
 559
 560
 561 // Enable HF antenna drivers:
 562 assign pwr_oe1 = 1'b0;
 563 assign pwr_oe3 = 1'b0;
 564
 565 // TAGSIM_MOD: short circuit antenna with different resistances (modulated by sub_carrier modulated by mod_sig_coil)
 566 // for pwr_oe4 = 1 (tristate): antenna load = 10k || 33                 = 32,9 Ohms
 567 // for pwr_oe4 = 0 (active):   antenna load = 10k || 33 || 33   = 16,5 Ohms
 568 assign pwr_oe4 = mod_sig_coil & sub_carrier & (mod_type == `TAGSIM_MOD);
 569
 570 // This is all LF, so doesn't matter.
 571 assign pwr_oe2 = 1'b0;
 572 assign pwr_lo = 1'b0;
 573
 574
 575 assign dbg = negedge_cnt[3];
 576
 577 endmodule