FIX: `lf visa2000` - identified unknown nibble in checksum. Is not checksum, but...

[proxmark3-svn] / armsrc / iso14443a.c

  //-----------------------------------------------------------------------------
// Merlok - June 2011, 2012
// Gerhard de Koning Gans - May 2008
// Hagen Fritsch - June 2010
//
// This code is licensed to you under the terms of the GNU GPL, version 2 or,
// at your option, any later version. See the LICENSE.txt file for the text of
// the license.
//-----------------------------------------------------------------------------
// Routines to support ISO 14443 type A.
//-----------------------------------------------------------------------------
#include "iso14443a.h"

static uint32_t iso14a_timeout;
int rsamples = 0;
uint8_t trigger = 0;
// the block number for the ISO14443-4 PCB
static uint8_t iso14_pcb_blocknum = 0;

static uint8_t* free_buffer_pointer;

//
// ISO14443 timing:
//
// minimum time between the start bits of consecutive transfers from reader to tag: 7000 carrier (13.56Mhz) cycles
#define REQUEST_GUARD_TIME (7000/16 + 1)
// minimum time between last modulation of tag and next start bit from reader to tag: 1172 carrier cycles 
#define FRAME_DELAY_TIME_PICC_TO_PCD (1172/16 + 1) 
// bool LastCommandWasRequest = FALSE;

//
// Total delays including SSC-Transfers between ARM and FPGA. These are in carrier clock cycles (1/13,56MHz)
//
// When the PM acts as reader and is receiving tag data, it takes
// 3 ticks delay in the AD converter
// 16 ticks until the modulation detector completes and sets curbit
// 8 ticks until bit_to_arm is assigned from curbit
// 8*16 ticks for the transfer from FPGA to ARM
// 4*16 ticks until we measure the time
// - 8*16 ticks because we measure the time of the previous transfer 
#define DELAY_AIR2ARM_AS_READER (3 + 16 + 8 + 8*16 + 4*16 - 8*16) 

// When the PM acts as a reader and is sending, it takes
// 4*16 ticks until we can write data to the sending hold register
// 8*16 ticks until the SHR is transferred to the Sending Shift Register
// 8 ticks until the first transfer starts
// 8 ticks later the FPGA samples the data
// 1 tick to assign mod_sig_coil
#define DELAY_ARM2AIR_AS_READER (4*16 + 8*16 + 8 + 8 + 1)

// When the PM acts as tag and is receiving it takes
// 2 ticks delay in the RF part (for the first falling edge),
// 3 ticks for the A/D conversion,
// 8 ticks on average until the start of the SSC transfer,
// 8 ticks until the SSC samples the first data
// 7*16 ticks to complete the transfer from FPGA to ARM
// 8 ticks until the next ssp_clk rising edge
// 4*16 ticks until we measure the time 
// - 8*16 ticks because we measure the time of the previous transfer 
#define DELAY_AIR2ARM_AS_TAG (2 + 3 + 8 + 8 + 7*16 + 8 + 4*16 - 8*16)
 
// The FPGA will report its internal sending delay in
uint16_t FpgaSendQueueDelay;
// the 5 first bits are the number of bits buffered in mod_sig_buf
// the last three bits are the remaining ticks/2 after the mod_sig_buf shift
#define DELAY_FPGA_QUEUE (FpgaSendQueueDelay<<1)

// When the PM acts as tag and is sending, it takes
// 4*16 ticks until we can write data to the sending hold register
// 8*16 ticks until the SHR is transferred to the Sending Shift Register
// 8 ticks until the first transfer starts
// 8 ticks later the FPGA samples the data
// + a varying number of ticks in the FPGA Delay Queue (mod_sig_buf)
// + 1 tick to assign mod_sig_coil
#define DELAY_ARM2AIR_AS_TAG (4*16 + 8*16 + 8 + 8 + DELAY_FPGA_QUEUE + 1)

// When the PM acts as sniffer and is receiving tag data, it takes
// 3 ticks A/D conversion
// 14 ticks to complete the modulation detection
// 8 ticks (on average) until the result is stored in to_arm
// + the delays in transferring data - which is the same for
// sniffing reader and tag data and therefore not relevant
#define DELAY_TAG_AIR2ARM_AS_SNIFFER (3 + 14 + 8) 
 
// When the PM acts as sniffer and is receiving reader data, it takes
// 2 ticks delay in analogue RF receiver (for the falling edge of the 
// start bit, which marks the start of the communication)
// 3 ticks A/D conversion
// 8 ticks on average until the data is stored in to_arm.
// + the delays in transferring data - which is the same for
// sniffing reader and tag data and therefore not relevant
#define DELAY_READER_AIR2ARM_AS_SNIFFER (2 + 3 + 8) 

//variables used for timing purposes:
//these are in ssp_clk cycles:
static uint32_t NextTransferTime;
static uint32_t LastTimeProxToAirStart;
static uint32_t LastProxToAirDuration;

// CARD TO READER - manchester
// Sequence D: 11110000 modulation with subcarrier during first half
// Sequence E: 00001111 modulation with subcarrier during second half
// Sequence F: 00000000 no modulation with subcarrier
// READER TO CARD - miller
// Sequence X: 00001100 drop after half a period
// Sequence Y: 00000000 no drop
// Sequence Z: 11000000 drop at start
#define SEC_D 0xf0
#define SEC_E 0x0f
#define SEC_F 0x00
#define SEC_X 0x0c
#define SEC_Y 0x00
#define SEC_Z 0xc0

void iso14a_set_trigger(bool enable) {
        trigger = enable;
}

void iso14a_set_timeout(uint32_t timeout) {
        iso14a_timeout = timeout;
        if(MF_DBGLEVEL >= 3) Dbprintf("ISO14443A Timeout set to %ld (%dms)", iso14a_timeout, iso14a_timeout / 106);
}

void iso14a_set_ATS_timeout(uint8_t *ats) {
        uint8_t tb1;
        uint8_t fwi; 
        uint32_t fwt;
        
        if (ats[0] > 1) {                                                       // there is a format byte T0
                if ((ats[1] & 0x20) == 0x20) {                  // there is an interface byte TB(1)

                        if ((ats[1] & 0x10) == 0x10)            // there is an interface byte TA(1) preceding TB(1)
                                tb1 = ats[3];
                        else
                                tb1 = ats[2];

                        fwi = (tb1 & 0xf0) >> 4;                        // frame waiting indicator (FWI)
                        fwt = 256 * 16 * (1 << fwi);            // frame waiting time (FWT) in 1/fc
                        //fwt = 4096 * (1 << fwi);
                        
                        iso14a_set_timeout(fwt/(8*16));
                        //iso14a_set_timeout(fwt/128);
                }
        }
}

//-----------------------------------------------------------------------------
// Generate the parity value for a byte sequence
//
//-----------------------------------------------------------------------------
void GetParity(const uint8_t *pbtCmd, uint16_t iLen, uint8_t *par) {
        uint16_t paritybit_cnt = 0;
        uint16_t paritybyte_cnt = 0;
        uint8_t parityBits = 0;

        for (uint16_t i = 0; i < iLen; i++) {
                // Generate the parity bits
                parityBits |= ((oddparity8(pbtCmd[i])) << (7-paritybit_cnt));
                if (paritybit_cnt == 7) {
                        par[paritybyte_cnt] = parityBits;       // save 8 Bits parity
                        parityBits = 0;                                         // and advance to next Parity Byte
                        paritybyte_cnt++;
                        paritybit_cnt = 0;
                } else {
                        paritybit_cnt++;
                }
        }

        // save remaining parity bits
        par[paritybyte_cnt] = parityBits;       
}

void AppendCrc14443a(uint8_t* data, int len) {
        ComputeCrc14443(CRC_14443_A,data,len,data+len,data+len+1);
}

//=============================================================================
// ISO 14443 Type A - Miller decoder
//=============================================================================
// Basics:
// This decoder is used when the PM3 acts as a tag.
// The reader will generate "pauses" by temporarily switching of the field. 
// At the PM3 antenna we will therefore measure a modulated antenna voltage. 
// The FPGA does a comparison with a threshold and would deliver e.g.:
// ........  1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 1  .......
// The Miller decoder needs to identify the following sequences:
// 2 (or 3) ticks pause followed by 6 (or 5) ticks unmodulated:         pause at beginning - Sequence Z ("start of communication" or a "0")
// 8 ticks without a modulation:                                                                        no pause - Sequence Y (a "0" or "end of communication" or "no information")
// 4 ticks unmodulated followed by 2 (or 3) ticks pause:                        pause in second half - Sequence X (a "1")
// Note 1: the bitstream may start at any time. We therefore need to sync.
// Note 2: the interpretation of Sequence Y and Z depends on the preceding sequence.
//-----------------------------------------------------------------------------
static tUart Uart;

// Lookup-Table to decide if 4 raw bits are a modulation.
// We accept the following:
// 0001  -   a 3 tick wide pause
// 0011  -   a 2 tick wide pause, or a three tick wide pause shifted left
// 0111  -   a 2 tick wide pause shifted left
// 1001  -   a 2 tick wide pause shifted right
const bool Mod_Miller_LUT[] = {
        FALSE,  TRUE, FALSE, TRUE,  FALSE, FALSE, FALSE, TRUE,
        FALSE,  TRUE, FALSE, FALSE, FALSE, FALSE, FALSE, FALSE
};
#define IsMillerModulationNibble1(b) (Mod_Miller_LUT[(b & 0x000000F0) >> 4])
#define IsMillerModulationNibble2(b) (Mod_Miller_LUT[(b & 0x0000000F)])

void UartReset() {
        Uart.state = STATE_UNSYNCD;
        Uart.bitCount = 0;
        Uart.len = 0;                                           // number of decoded data bytes
        Uart.parityLen = 0;                                     // number of decoded parity bytes
        Uart.shiftReg = 0;                                      // shiftreg to hold decoded data bits
        Uart.parityBits = 0;                            // holds 8 parity bits
        Uart.startTime = 0;
        Uart.endTime = 0;
        
        Uart.byteCntMax = 0;
        Uart.posCnt = 0;
        Uart.syncBit = 9999;
}

void UartInit(uint8_t *data, uint8_t *parity) {
        Uart.output = data;
        Uart.parity = parity;
        Uart.fourBits = 0x00000000;                     // clear the buffer for 4 Bits
        UartReset();
}

// use parameter non_real_time to provide a timestamp. Set to 0 if the decoder should measure real time
static RAMFUNC bool MillerDecoding(uint8_t bit, uint32_t non_real_time) {
        Uart.fourBits = (Uart.fourBits << 8) | bit;
        
        if (Uart.state == STATE_UNSYNCD) {                                                                                      // not yet synced
                        Uart.syncBit = 9999;                                                                                            // not set
                
                // 00x11111 2|3 ticks pause followed by 6|5 ticks unmodulated           Sequence Z (a "0" or "start of communication")
                // 11111111 8 ticks unmodulation                                                                        Sequence Y (a "0" or "end of communication" or "no information")
                // 111100x1 4 ticks unmodulated followed by 2|3 ticks pause                     Sequence X (a "1")

                // The start bit is one ore more Sequence Y followed by a Sequence Z (... 11111111 00x11111). We need to distinguish from
                // Sequence X followed by Sequence Y followed by Sequence Z     (111100x1 11111111 00x11111)
                // we therefore look for a ...xx1111 11111111 00x11111xxxxxx... pattern 
                // (12 '1's followed by 2 '0's, eventually followed by another '0', followed by 5 '1's)
                //
#define ISO14443A_STARTBIT_MASK         0x07FFEF80              // mask is    00001111 11111111 1110 1111 10000000
#define ISO14443A_STARTBIT_PATTERN      0x07FF8F80              // pattern is 00001111 11111111 1000 1111 10000000

                if              ((Uart.fourBits & (ISO14443A_STARTBIT_MASK >> 0)) == ISO14443A_STARTBIT_PATTERN >> 0) Uart.syncBit = 7;
                else if ((Uart.fourBits & (ISO14443A_STARTBIT_MASK >> 1)) == ISO14443A_STARTBIT_PATTERN >> 1) Uart.syncBit = 6;
                else if ((Uart.fourBits & (ISO14443A_STARTBIT_MASK >> 2)) == ISO14443A_STARTBIT_PATTERN >> 2) Uart.syncBit = 5;
                else if ((Uart.fourBits & (ISO14443A_STARTBIT_MASK >> 3)) == ISO14443A_STARTBIT_PATTERN >> 3) Uart.syncBit = 4;
                else if ((Uart.fourBits & (ISO14443A_STARTBIT_MASK >> 4)) == ISO14443A_STARTBIT_PATTERN >> 4) Uart.syncBit = 3;
                else if ((Uart.fourBits & (ISO14443A_STARTBIT_MASK >> 5)) == ISO14443A_STARTBIT_PATTERN >> 5) Uart.syncBit = 2;
                else if ((Uart.fourBits & (ISO14443A_STARTBIT_MASK >> 6)) == ISO14443A_STARTBIT_PATTERN >> 6) Uart.syncBit = 1;
                else if ((Uart.fourBits & (ISO14443A_STARTBIT_MASK >> 7)) == ISO14443A_STARTBIT_PATTERN >> 7) Uart.syncBit = 0;

                if (Uart.syncBit != 9999) {                                                                                             // found a sync bit
                        Uart.startTime = non_real_time ? non_real_time : (GetCountSspClk() & 0xfffffff8);
                        Uart.startTime -= Uart.syncBit;
                        Uart.endTime = Uart.startTime;
                        Uart.state = STATE_START_OF_COMMUNICATION;
                }
        } else {

                if (IsMillerModulationNibble1(Uart.fourBits >> Uart.syncBit)) {                 
                        if (IsMillerModulationNibble2(Uart.fourBits >> Uart.syncBit)) {         // Modulation in both halves - error
                                UartReset();
                        } else {                                                                                                                        // Modulation in first half = Sequence Z = logic "0"
                                if (Uart.state == STATE_MILLER_X) {                                                             // error - must not follow after X
                                        UartReset();
                                } else {
                                        Uart.bitCount++;
                                        Uart.shiftReg = (Uart.shiftReg >> 1);                                           // add a 0 to the shiftreg
                                        Uart.state = STATE_MILLER_Z;
                                        Uart.endTime = Uart.startTime + 8*(9*Uart.len + Uart.bitCount + 1) - 6;
                                        if(Uart.bitCount >= 9) {                                                                        // if we decoded a full byte (including parity)
                                                Uart.output[Uart.len++] = (Uart.shiftReg & 0xff);
                                                Uart.parityBits <<= 1;                                                                  // make room for the parity bit
                                                Uart.parityBits |= ((Uart.shiftReg >> 8) & 0x01);               // store parity bit
                                                Uart.bitCount = 0;
                                                Uart.shiftReg = 0;
                                                if((Uart.len&0x0007) == 0) {                                                    // every 8 data bytes
                                                        Uart.parity[Uart.parityLen++] = Uart.parityBits;        // store 8 parity bits
                                                        Uart.parityBits = 0;
                                                }
                                        }
                                }
                        }
                } else {
                        if (IsMillerModulationNibble2(Uart.fourBits >> Uart.syncBit)) {         // Modulation second half = Sequence X = logic "1"
                                Uart.bitCount++;
                                Uart.shiftReg = (Uart.shiftReg >> 1) | 0x100;                                   // add a 1 to the shiftreg
                                Uart.state = STATE_MILLER_X;
                                Uart.endTime = Uart.startTime + 8*(9*Uart.len + Uart.bitCount + 1) - 2;
                                if(Uart.bitCount >= 9) {                                                                                // if we decoded a full byte (including parity)
                                        Uart.output[Uart.len++] = (Uart.shiftReg & 0xff);
                                        Uart.parityBits <<= 1;                                                                          // make room for the new parity bit
                                        Uart.parityBits |= ((Uart.shiftReg >> 8) & 0x01);                       // store parity bit
                                        Uart.bitCount = 0;
                                        Uart.shiftReg = 0;
                                        if ((Uart.len&0x0007) == 0) {                                                           // every 8 data bytes
                                                Uart.parity[Uart.parityLen++] = Uart.parityBits;                // store 8 parity bits
                                                Uart.parityBits = 0;
                                        }
                                }
                        } else {                                                                                                                        // no modulation in both halves - Sequence Y
                                if (Uart.state == STATE_MILLER_Z || Uart.state == STATE_MILLER_Y) {     // Y after logic "0" - End of Communication
                                        Uart.state = STATE_UNSYNCD;
                                        Uart.bitCount--;                                                                                        // last "0" was part of EOC sequence
                                        Uart.shiftReg <<= 1;                                                                            // drop it
                                        if(Uart.bitCount > 0) {                                                                         // if we decoded some bits
                                                Uart.shiftReg >>= (9 - Uart.bitCount);                                  // right align them
                                                Uart.output[Uart.len++] = (Uart.shiftReg & 0xff);               // add last byte to the output
                                                Uart.parityBits <<= 1;                                                                  // add a (void) parity bit
                                                Uart.parityBits <<= (8 - (Uart.len&0x0007));                    // left align parity bits
                                                Uart.parity[Uart.parityLen++] = Uart.parityBits;                // and store it
                                                return TRUE;
                                        } else if (Uart.len & 0x0007) {                                                         // there are some parity bits to store
                                                Uart.parityBits <<= (8 - (Uart.len&0x0007));                    // left align remaining parity bits
                                                Uart.parity[Uart.parityLen++] = Uart.parityBits;                // and store them
                                        }
                                        if (Uart.len) {
                                                return TRUE;                                                                                    // we are finished with decoding the raw data sequence
                                        } else {
                                                UartReset();                                                                                    // Nothing received - start over
                                        }
                                }
                                if (Uart.state == STATE_START_OF_COMMUNICATION) {                               // error - must not follow directly after SOC
                                        UartReset();
                                } else {                                                                                                                // a logic "0"
                                        Uart.bitCount++;
                                        Uart.shiftReg = (Uart.shiftReg >> 1);                                           // add a 0 to the shiftreg
                                        Uart.state = STATE_MILLER_Y;
                                        if(Uart.bitCount >= 9) {                                                                        // if we decoded a full byte (including parity)
                                                Uart.output[Uart.len++] = (Uart.shiftReg & 0xff);
                                                Uart.parityBits <<= 1;                                                                  // make room for the parity bit
                                                Uart.parityBits |= ((Uart.shiftReg >> 8) & 0x01);               // store parity bit
                                                Uart.bitCount = 0;
                                                Uart.shiftReg = 0;
                                                if ((Uart.len&0x0007) == 0) {                                                   // every 8 data bytes
                                                        Uart.parity[Uart.parityLen++] = Uart.parityBits;        // store 8 parity bits
                                                        Uart.parityBits = 0;
                                                }
                                        }
                                }
                        }
                }
        } 
    return FALSE;       // not finished yet, need more data
}

//=============================================================================
// ISO 14443 Type A - Manchester decoder
//=============================================================================
// Basics:
// This decoder is used when the PM3 acts as a reader.
// The tag will modulate the reader field by asserting different loads to it. As a consequence, the voltage
// at the reader antenna will be modulated as well. The FPGA detects the modulation for us and would deliver e.g. the following:
// ........ 0 0 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 .......
// The Manchester decoder needs to identify the following sequences:
// 4 ticks modulated followed by 4 ticks unmodulated:   Sequence D = 1 (also used as "start of communication")
// 4 ticks unmodulated followed by 4 ticks modulated:   Sequence E = 0
// 8 ticks unmodulated:                                                                 Sequence F = end of communication
// 8 ticks modulated:                                                                   A collision. Save the collision position and treat as Sequence D
// Note 1: the bitstream may start at any time. We therefore need to sync.
// Note 2: parameter offset is used to determine the position of the parity bits (required for the anticollision command only)
static tDemod Demod;

// Lookup-Table to decide if 4 raw bits are a modulation.
// We accept three or four "1" in any position
const bool Mod_Manchester_LUT[] = {
        FALSE, FALSE, FALSE, FALSE, FALSE, FALSE, FALSE, TRUE,
        FALSE, FALSE, FALSE, TRUE,  FALSE, TRUE,  TRUE,  TRUE
};

#define IsManchesterModulationNibble1(b) (Mod_Manchester_LUT[(b & 0x00F0) >> 4])
#define IsManchesterModulationNibble2(b) (Mod_Manchester_LUT[(b & 0x000F)])

void DemodReset() {
        Demod.state = DEMOD_UNSYNCD;
        Demod.len = 0;                                          // number of decoded data bytes
        Demod.parityLen = 0;
        Demod.shiftReg = 0;                                     // shiftreg to hold decoded data bits
        Demod.parityBits = 0;                           // 
        Demod.collisionPos = 0;                         // Position of collision bit
        Demod.twoBits = 0xffff;                         // buffer for 2 Bits
        Demod.highCnt = 0;
        Demod.startTime = 0;
        Demod.endTime = 0;      
        Demod.bitCount = 0;
        Demod.syncBit = 0xFFFF;
        Demod.samples = 0;
}

void DemodInit(uint8_t *data, uint8_t *parity) {
        Demod.output = data;
        Demod.parity = parity;
        DemodReset();
}

// use parameter non_real_time to provide a timestamp. Set to 0 if the decoder should measure real time
static RAMFUNC int ManchesterDecoding(uint8_t bit, uint16_t offset, uint32_t non_real_time) {
        Demod.twoBits = (Demod.twoBits << 8) | bit;
        
        if (Demod.state == DEMOD_UNSYNCD) {

                if (Demod.highCnt < 2) {                                                                                        // wait for a stable unmodulated signal
                        if (Demod.twoBits == 0x0000) {
                                Demod.highCnt++;
                        } else {
                                Demod.highCnt = 0;
                        }
                } else {
                        Demod.syncBit = 0xFFFF;                 // not set
                        if              ((Demod.twoBits & 0x7700) == 0x7000) Demod.syncBit = 7; 
                        else if ((Demod.twoBits & 0x3B80) == 0x3800) Demod.syncBit = 6;
                        else if ((Demod.twoBits & 0x1DC0) == 0x1C00) Demod.syncBit = 5;
                        else if ((Demod.twoBits & 0x0EE0) == 0x0E00) Demod.syncBit = 4;
                        else if ((Demod.twoBits & 0x0770) == 0x0700) Demod.syncBit = 3;
                        else if ((Demod.twoBits & 0x03B8) == 0x0380) Demod.syncBit = 2;
                        else if ((Demod.twoBits & 0x01DC) == 0x01C0) Demod.syncBit = 1;
                        else if ((Demod.twoBits & 0x00EE) == 0x00E0) Demod.syncBit = 0;
                        if (Demod.syncBit != 0xFFFF) {
                                Demod.startTime = non_real_time?non_real_time:(GetCountSspClk() & 0xfffffff8);
                                Demod.startTime -= Demod.syncBit;
                                Demod.bitCount = offset;                        // number of decoded data bits
                                Demod.state = DEMOD_MANCHESTER_DATA;
                        }
                }
        } else {

                if (IsManchesterModulationNibble1(Demod.twoBits >> Demod.syncBit)) {            // modulation in first half
                        if (IsManchesterModulationNibble2(Demod.twoBits >> Demod.syncBit)) {    // ... and in second half = collision
                                if (!Demod.collisionPos) {
                                        Demod.collisionPos = (Demod.len << 3) + Demod.bitCount;
                                }
                        }                                                                                                                       // modulation in first half only - Sequence D = 1
                        Demod.bitCount++;
                        Demod.shiftReg = (Demod.shiftReg >> 1) | 0x100;                         // in both cases, add a 1 to the shiftreg
                        if(Demod.bitCount == 9) {                                                                       // if we decoded a full byte (including parity)
                                Demod.output[Demod.len++] = (Demod.shiftReg & 0xff);
                                Demod.parityBits <<= 1;                                                                 // make room for the parity bit
                                Demod.parityBits |= ((Demod.shiftReg >> 8) & 0x01);     // store parity bit
                                Demod.bitCount = 0;
                                Demod.shiftReg = 0;
                                if((Demod.len&0x0007) == 0) {                                                   // every 8 data bytes
                                        Demod.parity[Demod.parityLen++] = Demod.parityBits;     // store 8 parity bits
                                        Demod.parityBits = 0;
                                }
                        }
                        Demod.endTime = Demod.startTime + 8*(9*Demod.len + Demod.bitCount + 1) - 4;
                } else {                                                                                                                // no modulation in first half
                        if (IsManchesterModulationNibble2(Demod.twoBits >> Demod.syncBit)) {    // and modulation in second half = Sequence E = 0
                                Demod.bitCount++;
                                Demod.shiftReg = (Demod.shiftReg >> 1);                                 // add a 0 to the shiftreg
                                if(Demod.bitCount >= 9) {                                                               // if we decoded a full byte (including parity)
                                        Demod.output[Demod.len++] = (Demod.shiftReg & 0xff);
                                        Demod.parityBits <<= 1;                                                         // make room for the new parity bit
                                        Demod.parityBits |= ((Demod.shiftReg >> 8) & 0x01); // store parity bit
                                        Demod.bitCount = 0;
                                        Demod.shiftReg = 0;
                                        if ((Demod.len&0x0007) == 0) {                                          // every 8 data bytes
                                                Demod.parity[Demod.parityLen++] = Demod.parityBits;     // store 8 parity bits1
                                                Demod.parityBits = 0;
                                        }
                                }
                                Demod.endTime = Demod.startTime + 8*(9*Demod.len + Demod.bitCount + 1);
                        } else {                                                                                                        // no modulation in both halves - End of communication
                                if(Demod.bitCount > 0) {                                                                // there are some remaining data bits
                                        Demod.shiftReg >>= (9 - Demod.bitCount);                        // right align the decoded bits
                                        Demod.output[Demod.len++] = Demod.shiftReg & 0xff;      // and add them to the output
                                        Demod.parityBits <<= 1;                                                         // add a (void) parity bit
                                        Demod.parityBits <<= (8 - (Demod.len&0x0007));          // left align remaining parity bits
                                        Demod.parity[Demod.parityLen++] = Demod.parityBits;     // and store them
                                        return TRUE;
                                } else if (Demod.len & 0x0007) {                                                // there are some parity bits to store
                                        Demod.parityBits <<= (8 - (Demod.len&0x0007));          // left align remaining parity bits
                                        Demod.parity[Demod.parityLen++] = Demod.parityBits;     // and store them
                                }
                                if (Demod.len) {
                                        return TRUE;                                                                            // we are finished with decoding the raw data sequence
                                } else {                                                                                                // nothing received. Start over
                                        DemodReset();
                                }
                        }
                }
        } 
    return FALSE;       // not finished yet, need more data
}

//=============================================================================
// Finally, a `sniffer' for ISO 14443 Type A
// Both sides of communication!
//=============================================================================

//-----------------------------------------------------------------------------
// Record the sequence of commands sent by the reader to the tag, with
// triggering so that we start recording at the point that the tag is moved
// near the reader.
// "hf 14a sniff"
//-----------------------------------------------------------------------------
void RAMFUNC SniffIso14443a(uint8_t param) {
        // param:
        // bit 0 - trigger from first card answer
        // bit 1 - trigger from first reader 7-bit request
        LEDsoff();

        iso14443a_setup(FPGA_HF_ISO14443A_SNIFFER);
        
        // Allocate memory from BigBuf for some buffers
        // free all previous allocations first
        BigBuf_free(); BigBuf_Clear_ext(false);
        clear_trace();
        set_tracing(TRUE);
        
        // The command (reader -> tag) that we're receiving.
        uint8_t *receivedCmd = BigBuf_malloc(MAX_FRAME_SIZE);
        uint8_t *receivedCmdPar = BigBuf_malloc(MAX_PARITY_SIZE);
        
        // The response (tag -> reader) that we're receiving.
        uint8_t *receivedResponse = BigBuf_malloc(MAX_FRAME_SIZE);
        uint8_t *receivedResponsePar = BigBuf_malloc(MAX_PARITY_SIZE);
        
        // The DMA buffer, used to stream samples from the FPGA
        uint8_t *dmaBuf = BigBuf_malloc(DMA_BUFFER_SIZE);

        uint8_t *data = dmaBuf;
        uint8_t previous_data = 0;
        int maxDataLen = 0;
        int dataLen = 0;
        bool TagIsActive = FALSE;
        bool ReaderIsActive = FALSE;
        
        // Set up the demodulator for tag -> reader responses.
        DemodInit(receivedResponse, receivedResponsePar);
        
        // Set up the demodulator for the reader -> tag commands
        UartInit(receivedCmd, receivedCmdPar);
        
        // Setup and start DMA.
        if ( !FpgaSetupSscDma((uint8_t*) dmaBuf, DMA_BUFFER_SIZE) ){
                if (MF_DBGLEVEL > 1) Dbprintf("FpgaSetupSscDma failed. Exiting"); 
                return;
        }
        
        // We won't start recording the frames that we acquire until we trigger;
        // a good trigger condition to get started is probably when we see a
        // response from the tag.
        // triggered == FALSE -- to wait first for card
        bool triggered = !(param & 0x03); 
        
        // And now we loop, receiving samples.
        for(uint32_t rsamples = 0; TRUE; ) {

                if(BUTTON_PRESS()) {
                        DbpString("cancelled by button");
                        break;
                }

                LED_A_ON();
                WDT_HIT();

                int register readBufDataP = data - dmaBuf;
                int register dmaBufDataP = DMA_BUFFER_SIZE - AT91C_BASE_PDC_SSC->PDC_RCR;
                if (readBufDataP <= dmaBufDataP){
                        dataLen = dmaBufDataP - readBufDataP;
                } else {
                        dataLen = DMA_BUFFER_SIZE - readBufDataP + dmaBufDataP;
                }
                // test for length of buffer
                if(dataLen > maxDataLen) {
                        maxDataLen = dataLen;
                        if(dataLen > (9 * DMA_BUFFER_SIZE / 10)) {
                                Dbprintf("blew circular buffer! dataLen=%d", dataLen);
                                break;
                        }
                }
                if(dataLen < 1) continue;

                // primary buffer was stopped( <-- we lost data!
                if (!AT91C_BASE_PDC_SSC->PDC_RCR) {
                        AT91C_BASE_PDC_SSC->PDC_RPR = (uint32_t) dmaBuf;
                        AT91C_BASE_PDC_SSC->PDC_RCR = DMA_BUFFER_SIZE;
                        Dbprintf("RxEmpty ERROR!!! data length:%d", dataLen); // temporary
                }
                // secondary buffer sets as primary, secondary buffer was stopped
                if (!AT91C_BASE_PDC_SSC->PDC_RNCR) {
                        AT91C_BASE_PDC_SSC->PDC_RNPR = (uint32_t) dmaBuf;
                        AT91C_BASE_PDC_SSC->PDC_RNCR = DMA_BUFFER_SIZE;
                }

                LED_A_OFF();
                
                if (rsamples & 0x01) {                          // Need two samples to feed Miller and Manchester-Decoder

                        if(!TagIsActive) {              // no need to try decoding reader data if the tag is sending
                                uint8_t readerdata = (previous_data & 0xF0) | (*data >> 4);
                                if (MillerDecoding(readerdata, (rsamples-1)*4)) {
                                        LED_C_ON();

                                        // check - if there is a short 7bit request from reader
                                        if ((!triggered) && (param & 0x02) && (Uart.len == 1) && (Uart.bitCount == 7)) triggered = TRUE;

                                        if(triggered) {
                                                if (!LogTrace(receivedCmd, 
                                                                                Uart.len, 
                                                                                Uart.startTime*16 - DELAY_READER_AIR2ARM_AS_SNIFFER,
                                                                                Uart.endTime*16 - DELAY_READER_AIR2ARM_AS_SNIFFER,
                                                                                Uart.parity, 
                                                                                TRUE)) break;
                                        }
                                        /* And ready to receive another command. */
                                        UartReset();
                                        /* And also reset the demod code, which might have been */
                                        /* false-triggered by the commands from the reader. */
                                        DemodReset();
                                        LED_B_OFF();
                                }
                                ReaderIsActive = (Uart.state != STATE_UNSYNCD);
                        }

                        if(!ReaderIsActive) {           // no need to try decoding tag data if the reader is sending - and we cannot afford the time
                                uint8_t tagdata = (previous_data << 4) | (*data & 0x0F);
                                if(ManchesterDecoding(tagdata, 0, (rsamples-1)*4)) {
                                        LED_B_ON();

                                        if (!LogTrace(receivedResponse, 
                                                                        Demod.len, 
                                                                        Demod.startTime*16 - DELAY_TAG_AIR2ARM_AS_SNIFFER, 
                                                                        Demod.endTime*16 - DELAY_TAG_AIR2ARM_AS_SNIFFER,
                                                                        Demod.parity,
                                                                        FALSE)) break;

                                        if ((!triggered) && (param & 0x01)) triggered = TRUE;

                                        // And ready to receive another response.
                                        DemodReset();
                                        // And reset the Miller decoder including itS (now outdated) input buffer
                                        UartInit(receivedCmd, receivedCmdPar);
                                        LED_C_OFF();
                                } 
                                TagIsActive = (Demod.state != DEMOD_UNSYNCD);
                        }
                }

                previous_data = *data;
                rsamples++;
                data++;
                if(data == dmaBuf + DMA_BUFFER_SIZE) {
                        data = dmaBuf;
                }
        } // main cycle

        if (MF_DBGLEVEL >= 1) {
                Dbprintf("maxDataLen=%d, Uart.state=%x, Uart.len=%d", maxDataLen, Uart.state, Uart.len);
                Dbprintf("traceLen=%d, Uart.output[0]=%08x", BigBuf_get_traceLen(), (uint32_t)Uart.output[0]);
        }
        FpgaDisableSscDma();
        FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
        LEDsoff();
        set_tracing(FALSE);     
}

//-----------------------------------------------------------------------------
// Prepare tag messages
//-----------------------------------------------------------------------------
static void CodeIso14443aAsTagPar(const uint8_t *cmd, uint16_t len, uint8_t *parity) {
        ToSendReset();

        // Correction bit, might be removed when not needed
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        ToSendStuffBit(1);  // 1
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        
        // Send startbit
        ToSend[++ToSendMax] = SEC_D;
        LastProxToAirDuration = 8 * ToSendMax - 4;

        for(uint16_t i = 0; i < len; i++) {
                uint8_t b = cmd[i];

                // Data bits
                for(uint16_t j = 0; j < 8; j++) {
                        if(b & 1) {
                                ToSend[++ToSendMax] = SEC_D;
                        } else {
                                ToSend[++ToSendMax] = SEC_E;
                        }
                        b >>= 1;
                }

                // Get the parity bit
                if (parity[i>>3] & (0x80>>(i&0x0007))) {
                        ToSend[++ToSendMax] = SEC_D;
                        LastProxToAirDuration = 8 * ToSendMax - 4;
                } else {
                        ToSend[++ToSendMax] = SEC_E;
                        LastProxToAirDuration = 8 * ToSendMax;
                }
        }

        // Send stopbit
        ToSend[++ToSendMax] = SEC_F;

        // Convert from last byte pos to length
        ++ToSendMax;
}

static void CodeIso14443aAsTag(const uint8_t *cmd, uint16_t len) {
        uint8_t par[MAX_PARITY_SIZE] = {0};
        GetParity(cmd, len, par);
        CodeIso14443aAsTagPar(cmd, len, par);
}

static void Code4bitAnswerAsTag(uint8_t cmd) {
        uint8_t b = cmd;

        ToSendReset();

        // Correction bit, might be removed when not needed
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        ToSendStuffBit(1);  // 1
        ToSendStuffBit(0);
        ToSendStuffBit(0);
        ToSendStuffBit(0);

        // Send startbit
        ToSend[++ToSendMax] = SEC_D;

        for(uint8_t i = 0; i < 4; i++) {
                if(b & 1) {
                        ToSend[++ToSendMax] = SEC_D;
                        LastProxToAirDuration = 8 * ToSendMax - 4;
                } else {
                        ToSend[++ToSendMax] = SEC_E;
                        LastProxToAirDuration = 8 * ToSendMax;
                }
                b >>= 1;
        }

        // Send stopbit
        ToSend[++ToSendMax] = SEC_F;

        // Convert from last byte pos to length
        ToSendMax++;
}

//-----------------------------------------------------------------------------
// Wait for commands from reader
// Stop when button is pressed
// Or return TRUE when command is captured
//-----------------------------------------------------------------------------
int GetIso14443aCommandFromReader(uint8_t *received, uint8_t *parity, int *len) {
    // Set FPGA mode to "simulated ISO 14443 tag", no modulation (listen
    // only, since we are receiving, not transmitting).
    // Signal field is off with the appropriate LED
    LED_D_OFF();
    FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_ISO14443A | FPGA_HF_ISO14443A_TAGSIM_LISTEN);

    // Now run a `software UART` on the stream of incoming samples.
        UartInit(received, parity);

        // clear RXRDY:
    uint8_t b = (uint8_t)AT91C_BASE_SSC->SSC_RHR;

    for(;;) {
        WDT_HIT();

        if(BUTTON_PRESS()) return FALSE;
                
        if(AT91C_BASE_SSC->SSC_SR & (AT91C_SSC_RXRDY)) {
            b = (uint8_t)AT91C_BASE_SSC->SSC_RHR;
                        if(MillerDecoding(b, 0)) {
                                *len = Uart.len;
                                return TRUE;
                        }
                }
    }
}

bool prepare_tag_modulation(tag_response_info_t* response_info, size_t max_buffer_size) {
        // Example response, answer to MIFARE Classic read block will be 16 bytes + 2 CRC = 18 bytes
        // This will need the following byte array for a modulation sequence
        //    144        data bits (18 * 8)
        //     18        parity bits
        //      2        Start and stop
        //      1        Correction bit (Answer in 1172 or 1236 periods, see FPGA)
        //      1        just for the case
        // ----------- +
        //    166 bytes, since every bit that needs to be send costs us a byte
        //
        // Prepare the tag modulation bits from the message
        CodeIso14443aAsTag(response_info->response,response_info->response_n);

        // Make sure we do not exceed the free buffer space
        if (ToSendMax > max_buffer_size) {
                Dbprintf("Out of memory, when modulating bits for tag answer:");
                Dbhexdump(response_info->response_n,response_info->response,false);
                return FALSE;
        }

        // Copy the byte array, used for this modulation to the buffer position
        memcpy(response_info->modulation,ToSend,ToSendMax);

        // Store the number of bytes that were used for encoding/modulation and the time needed to transfer them
        response_info->modulation_n = ToSendMax;
        response_info->ProxToAirDuration = LastProxToAirDuration;
        return TRUE;
}

// "precompile" responses. There are 7 predefined responses with a total of 28 bytes data to transmit.
// Coded responses need one byte per bit to transfer (data, parity, start, stop, correction) 
// 28 * 8 data bits, 28 * 1 parity bits, 7 start bits, 7 stop bits, 7 correction bits
// -> need 273 bytes buffer
// 44 * 8 data bits, 44 * 1 parity bits, 9 start bits, 9 stop bits, 9 correction bits --370
// 47 * 8 data bits, 47 * 1 parity bits, 10 start bits, 10 stop bits, 10 correction bits 
#define ALLOCATED_TAG_MODULATION_BUFFER_SIZE 453 

bool prepare_allocated_tag_modulation(tag_response_info_t* response_info) {
        // Retrieve and store the current buffer index
        response_info->modulation = free_buffer_pointer;

        // Determine the maximum size we can use from our buffer
        size_t max_buffer_size = ALLOCATED_TAG_MODULATION_BUFFER_SIZE;

        // Forward the prepare tag modulation function to the inner function
        if (prepare_tag_modulation(response_info, max_buffer_size)) {
                // Update the free buffer offset
                free_buffer_pointer += ToSendMax;
                return true;
        } else {
                return false;
        }
}

//-----------------------------------------------------------------------------
// Main loop of simulated tag: receive commands from reader, decide what
// response to send, and send it.
// 'hf 14a sim'
//-----------------------------------------------------------------------------
void SimulateIso14443aTag(int tagType, int flags, byte_t* data) {

        #define ATTACK_KEY_COUNT 8 // keep same as define in cmdhfmf.c -> readerAttack()
        // init pseudorand
        fast_prand();
        
        uint8_t sak = 0;
        uint32_t cuid = 0;                      
        uint32_t nonce = 0;
        
        // PACK response to PWD AUTH for EV1/NTAG
        uint8_t response8[4] = {0,0,0,0};
        // Counter for EV1/NTAG
        uint32_t counters[] = {0,0,0};
        
        // The first response contains the ATQA (note: bytes are transmitted in reverse order).
        uint8_t response1[] = {0,0};

        // Here, we collect CUID, block1, keytype1, NT1, NR1, AR1, CUID, block2, keytyp2, NT2, NR2, AR2
        // it should also collect block, keytype.
        uint8_t cardAUTHSC = 0;
        uint8_t cardAUTHKEY = 0xff;  // no authentication
        // allow collecting up to 8 sets of nonces to allow recovery of up to 8 keys

        nonces_t ar_nr_nonces[ATTACK_KEY_COUNT]; // for attack types moebius
        memset(ar_nr_nonces, 0x00, sizeof(ar_nr_nonces));
        uint8_t moebius_count = 0;
        
        switch (tagType) {
                case 1: { // MIFARE Classic 1k 
                        response1[0] = 0x04;
                        sak = 0x08;
                } break;
                case 2: { // MIFARE Ultralight
                        response1[0] = 0x44;
                        sak = 0x00;
                } break;
                case 3: { // MIFARE DESFire
                        response1[0] = 0x04;
                        response1[1] = 0x03;
                        sak = 0x20;
                } break;
                case 4: { // ISO/IEC 14443-4 - javacard (JCOP)
                        response1[0] = 0x04;
                        sak = 0x28;
                } break;
                case 5: { // MIFARE TNP3XXX
                        response1[0] = 0x01;
                        response1[1] = 0x0f;
                        sak = 0x01;
                } break;
                case 6: { // MIFARE Mini 320b
                        response1[0] = 0x44;
                        sak = 0x09;
                } break;
                case 7: { // NTAG
                        response1[0] = 0x44;
                        sak = 0x00;
                        // PACK
                        response8[0] = 0x80;
                        response8[1] = 0x80;
                        ComputeCrc14443(CRC_14443_A, response8, 2, &response8[2], &response8[3]);
                        // uid not supplied then get from emulator memory
                        if (data[0]==0) {
                                uint16_t start = 4 * (0+12);  
                                uint8_t emdata[8];
                                emlGetMemBt( emdata, start, sizeof(emdata));
                                memcpy(data, emdata, 3); // uid bytes 0-2
                                memcpy(data+3, emdata+4, 4); // uid bytes 3-7
                                flags |= FLAG_7B_UID_IN_DATA;
                        }
                } break;        
                case 8: { // MIFARE Classic 4k
                        response1[0] = 0x02;
                        sak = 0x18;
                } break;
                default: {
                        Dbprintf("Error: unkown tagtype (%d)",tagType);
                        return;
                } break;
        }
        
        // The second response contains the (mandatory) first 24 bits of the UID
        uint8_t response2[5] = {0x00};

        // For UID size 7, 
        uint8_t response2a[5] = {0x00};
        
        if ( (flags & FLAG_7B_UID_IN_DATA) == FLAG_7B_UID_IN_DATA ) {
                response2[0] = 0x88;  // Cascade Tag marker
                response2[1] = data[0];
                response2[2] = data[1];
                response2[3] = data[2];

                response2a[0] = data[3];
                response2a[1] = data[4];
                response2a[2] = data[5];
                response2a[3] = data[6]; //??
                response2a[4] = response2a[0] ^ response2a[1] ^ response2a[2] ^ response2a[3];

                // Configure the ATQA and SAK accordingly
                response1[0] |= 0x40;
                sak |= 0x04;
                
                cuid = bytes_to_num(data+3, 4);
        } else {
                memcpy(response2, data, 4);
                // Configure the ATQA and SAK accordingly
                response1[0] &= 0xBF;
                sak &= 0xFB;
                cuid = bytes_to_num(data, 4);
        }

        // Calculate the BitCountCheck (BCC) for the first 4 bytes of the UID.
        response2[4] = response2[0] ^ response2[1] ^ response2[2] ^ response2[3];

        // Prepare the mandatory SAK (for 4 and 7 byte UID)
        uint8_t response3[3]  = {sak, 0x00, 0x00};
        ComputeCrc14443(CRC_14443_A, response3, 1, &response3[1], &response3[2]);

        // Prepare the optional second SAK (for 7 byte UID), drop the cascade bit
        uint8_t response3a[3]  = {0x00};
        response3a[0] = sak & 0xFB;
        ComputeCrc14443(CRC_14443_A, response3a, 1, &response3a[1], &response3a[2]);

        // Tag NONCE.
        uint8_t response5[4]; 
        
        uint8_t response6[] = { 0x04, 0x58, 0x80, 0x02, 0x00, 0x00 };   // dummy ATS (pseudo-ATR), answer to RATS: 
        // Format byte = 0x58: FSCI=0x08 (FSC=256), TA(1) and TC(1) present, 
        // TA(1) = 0x80: different divisors not supported, DR = 1, DS = 1
        // TB(1) = not present. Defaults: FWI = 4 (FWT = 256 * 16 * 2^4 * 1/fc = 4833us), SFGI = 0 (SFG = 256 * 16 * 2^0 * 1/fc = 302us)
        // TC(1) = 0x02: CID supported, NAD not supported
        ComputeCrc14443(CRC_14443_A, response6, 4, &response6[4], &response6[5]);
        
        // Prepare GET_VERSION (different for UL EV-1 / NTAG)
        // uint8_t response7_EV1[] = {0x00, 0x04, 0x03, 0x01, 0x01, 0x00, 0x0b, 0x03, 0xfd, 0xf7};  //EV1 48bytes VERSION.
        // uint8_t response7_NTAG[] = {0x00, 0x04, 0x04, 0x02, 0x01, 0x00, 0x11, 0x03, 0x01, 0x9e}; //NTAG 215  
        // Prepare CHK_TEARING
        // uint8_t response9[] =  {0xBD,0x90,0x3f};
        
        #define TAG_RESPONSE_COUNT 10
        tag_response_info_t responses[TAG_RESPONSE_COUNT] = {
                { .response = response1,  .response_n = sizeof(response1)  },  // Answer to request - respond with card type
                { .response = response2,  .response_n = sizeof(response2)  },  // Anticollision cascade1 - respond with uid
                { .response = response2a, .response_n = sizeof(response2a) },  // Anticollision cascade2 - respond with 2nd half of uid if asked
                { .response = response3,  .response_n = sizeof(response3)  },  // Acknowledge select - cascade 1
                { .response = response3a, .response_n = sizeof(response3a) },  // Acknowledge select - cascade 2
                { .response = response5,  .response_n = sizeof(response5)  },  // Authentication answer (random nonce)
                { .response = response6,  .response_n = sizeof(response6)  },  // dummy ATS (pseudo-ATR), answer to RATS

                { .response = response8,   .response_n = sizeof(response8) }  // EV1/NTAG PACK response
        };      
                // { .response = response7_NTAG, .response_n = sizeof(response7_NTAG)}, // EV1/NTAG GET_VERSION response
                // { .response = response9,      .response_n = sizeof(response9)     }  // EV1/NTAG CHK_TEAR response
        

        // Allocate 512 bytes for the dynamic modulation, created when the reader queries for it
        // Such a response is less time critical, so we can prepare them on the fly
        #define DYNAMIC_RESPONSE_BUFFER_SIZE 64
        #define DYNAMIC_MODULATION_BUFFER_SIZE 512
        uint8_t dynamic_response_buffer[DYNAMIC_RESPONSE_BUFFER_SIZE];
        uint8_t dynamic_modulation_buffer[DYNAMIC_MODULATION_BUFFER_SIZE];
        tag_response_info_t dynamic_response_info = {
                .response = dynamic_response_buffer,
                .response_n = 0,
                .modulation = dynamic_modulation_buffer,
                .modulation_n = 0
        };
  
        // We need to listen to the high-frequency, peak-detected path.
        iso14443a_setup(FPGA_HF_ISO14443A_TAGSIM_LISTEN);

        BigBuf_free_keep_EM();
        clear_trace();
        set_tracing(TRUE);

        // allocate buffers:
        uint8_t *receivedCmd = BigBuf_malloc(MAX_FRAME_SIZE);
        uint8_t *receivedCmdPar = BigBuf_malloc(MAX_PARITY_SIZE);
        free_buffer_pointer = BigBuf_malloc(ALLOCATED_TAG_MODULATION_BUFFER_SIZE);

        // Prepare the responses of the anticollision phase
        // there will be not enough time to do this at the moment the reader sends it REQA
        for (size_t i=0; i<TAG_RESPONSE_COUNT; i++)
                prepare_allocated_tag_modulation(&responses[i]);

        int len = 0;

        // To control where we are in the protocol
        int order = 0;
        int lastorder;

        // Just to allow some checks
        int happened = 0;
        int happened2 = 0;
        int cmdsRecvd = 0;
        tag_response_info_t* p_response;

        LED_A_ON();
        for(;;) {       
                WDT_HIT();
                
                // Clean receive command buffer
                if(!GetIso14443aCommandFromReader(receivedCmd, receivedCmdPar, &len)) {
                        Dbprintf("Emulator stopped. Tracing: %d  trace length: %d ", tracing, BigBuf_get_traceLen());
                        break;
                }       
                p_response = NULL;
                
                // Okay, look at the command now.
                lastorder = order;
                if(receivedCmd[0] == ISO14443A_CMD_REQA) { // Received a REQUEST
                        p_response = &responses[0]; order = 1;
                } else if(receivedCmd[0] == ISO14443A_CMD_WUPA) { // Received a WAKEUP
                        p_response = &responses[0]; order = 6;
                } else if(receivedCmd[1] == 0x20 && receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT) {       // Received request for UID (cascade 1)
                        p_response = &responses[1]; order = 2;
                } else if(receivedCmd[1] == 0x20 && receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT_2) {     // Received request for UID (cascade 2)
                        p_response = &responses[2]; order = 20;
                } else if(receivedCmd[1] == 0x70 && receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT) {       // Received a SELECT (cascade 1)
                        p_response = &responses[3]; order = 3;
                } else if(receivedCmd[1] == 0x70 && receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT_2) {     // Received a SELECT (cascade 2)
                        p_response = &responses[4]; order = 30;         
                } else if(receivedCmd[0] == ISO14443A_CMD_READBLOCK) {  // Received a (plain) READ
                        uint8_t block = receivedCmd[1];
                        // if Ultralight or NTAG (4 byte blocks)
                        if ( tagType == 7 || tagType == 2 ) {
                                // first 12 blocks of emu are [getversion answer - check tearing - pack - 0x00 - signature]
                                uint16_t start = 4 * (block+12);  
                                uint8_t emdata[MAX_MIFARE_FRAME_SIZE];
                                emlGetMemBt( emdata, start, 16);
                                AppendCrc14443a(emdata, 16);
                                EmSendCmdEx(emdata, sizeof(emdata), false);
                                // We already responded, do not send anything with the EmSendCmd14443aRaw() that is called below
                                p_response = NULL;
                        } else { // all other tags (16 byte block tags)
                                uint8_t emdata[MAX_MIFARE_FRAME_SIZE];
                                emlGetMemBt( emdata, block, 16);
                                AppendCrc14443a(emdata, 16);
                                EmSendCmdEx(emdata, sizeof(emdata), false);
                                // EmSendCmdEx(data+(4*receivedCmd[1]),16,false);
                                // Dbprintf("Read request from reader: %x %x",receivedCmd[0],receivedCmd[1]);
                                // We already responded, do not send anything with the EmSendCmd14443aRaw() that is called below
                                p_response = NULL;
                        }
                } else if(receivedCmd[0] == MIFARE_ULEV1_FASTREAD) {    // Received a FAST READ (ranged read)                           
                        uint8_t emdata[MAX_FRAME_SIZE];
                        // first 12 blocks of emu are [getversion answer - check tearing - pack - 0x00 - signature]
                        int start =  (receivedCmd[1]+12) * 4; 
                        int len   = (receivedCmd[2] - receivedCmd[1] + 1) * 4;
                        emlGetMemBt( emdata, start, len);
                        AppendCrc14443a(emdata, len);
                        EmSendCmdEx(emdata, len+2, false);                              
                        p_response = NULL;              
                } else if(receivedCmd[0] == MIFARE_ULEV1_READSIG && tagType == 7) {     // Received a READ SIGNATURE -- 
                        // first 12 blocks of emu are [getversion answer - check tearing - pack - 0x00 - signature]
                        uint16_t start = 4 * 4;
                        uint8_t emdata[34];
                        emlGetMemBt( emdata, start, 32);
                        AppendCrc14443a(emdata, 32);
                        EmSendCmdEx(emdata, sizeof(emdata), false);
                        p_response = NULL;                                      
                } else if (receivedCmd[0] == MIFARE_ULEV1_READ_CNT && tagType == 7) {   // Received a READ COUNTER -- 
                        uint8_t index = receivedCmd[1];
                        uint8_t cmd[] =  {0x00,0x00,0x00,0x14,0xa5};
                        if ( counters[index] > 0) {
                                num_to_bytes(counters[index], 3, cmd);
                                AppendCrc14443a(cmd, sizeof(cmd)-2);
                        }
                        EmSendCmdEx(cmd,sizeof(cmd),false);                             
                        p_response = NULL;
                } else if (receivedCmd[0] == MIFARE_ULEV1_INCR_CNT && tagType == 7) {   // Received a INC COUNTER -- 
                        // number of counter
                        uint8_t counter = receivedCmd[1];
                        uint32_t val = bytes_to_num(receivedCmd+2,4);
                        counters[counter] = val;
                
                        // send ACK
                        uint8_t ack[] = {0x0a};
                        EmSendCmdEx(ack,sizeof(ack),false);
                        p_response = NULL;                      
                } else if(receivedCmd[0] == MIFARE_ULEV1_CHECKTEAR && tagType == 7) {   // Received a CHECK_TEARING_EVENT -- 
                        // first 12 blocks of emu are [getversion answer - check tearing - pack - 0x00 - signature]
                        uint8_t emdata[3];
                        uint8_t counter=0;
                        if (receivedCmd[1]<3) counter = receivedCmd[1];
                        emlGetMemBt( emdata, 10+counter, 1);
                        AppendCrc14443a(emdata, sizeof(emdata)-2);
                        EmSendCmdEx(emdata, sizeof(emdata), false);     
                        p_response = NULL;              
                } else if(receivedCmd[0] == ISO14443A_CMD_HALT) {       // Received a HALT
                        LogTrace(receivedCmd, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                        p_response = NULL;
                } else if(receivedCmd[0] == MIFARE_AUTH_KEYA || receivedCmd[0] == MIFARE_AUTH_KEYB) {   // Received an authentication request                           
                        if ( tagType == 7 ) {   // IF NTAG /EV1  0x60 == GET_VERSION, not a authentication request.
                                uint8_t emdata[10];
                                emlGetMemBt( emdata, 0, 8 );
                                AppendCrc14443a(emdata, sizeof(emdata)-2);
                                EmSendCmdEx(emdata, sizeof(emdata), false);
                                p_response = NULL;
                        } else {
                                                                
                                cardAUTHKEY = receivedCmd[0] - 0x60;
                                cardAUTHSC = receivedCmd[1] / 4; // received block num
                                
                                // incease nonce at AUTH requests. this is time consuming.
                                nonce = prand();
                                //num_to_bytes(nonce, 4, response5);
                                num_to_bytes(nonce, 4, dynamic_response_info.response);                         
                                dynamic_response_info.response_n = 4;

                                //prepare_tag_modulation(&responses[5], DYNAMIC_MODULATION_BUFFER_SIZE);
                                prepare_tag_modulation(&dynamic_response_info, DYNAMIC_MODULATION_BUFFER_SIZE);
                                p_response = &dynamic_response_info;
                                //p_response = &responses[5]; 
                                order = 7;
                        }
                } else if(receivedCmd[0] == ISO14443A_CMD_RATS) {       // Received a RATS request
                        if (tagType == 1 || tagType == 2) {     // RATS not supported
                                EmSend4bit(CARD_NACK_NA);
                                p_response = NULL;
                        } else {
                                p_response = &responses[6]; order = 70;
                        }
                } else if (order == 7 && len == 8) { // Received {nr] and {ar} (part of authentication)
                        LogTrace(receivedCmd, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                        uint32_t nr = bytes_to_num(receivedCmd,4);
                        uint32_t ar = bytes_to_num(receivedCmd+4,4);
                 
                        // Collect AR/NR per keytype & sector
                        if ( (flags & FLAG_NR_AR_ATTACK) == FLAG_NR_AR_ATTACK ) {
                                
                                int8_t index = -1;
                                int8_t empty = -1;
                                for (uint8_t i = 0; i < ATTACK_KEY_COUNT; i++) {
                                        // find which index to use
                                        if ( (cardAUTHSC == ar_nr_nonces[i].sector) &&  (cardAUTHKEY == ar_nr_nonces[i].keytype)) 
                                                index = i;

                                        // keep track of empty slots.
                                        if ( ar_nr_nonces[i].state == EMPTY)
                                                empty = i;
                                }
                                // if no empty slots.  Choose first and overwrite.
                                if ( index == -1 ) {
                                        if ( empty == -1 ) {
                                                index = 0;
                                                ar_nr_nonces[index].state = EMPTY;
                                        } else {
                                                index = empty;
                                        }
                                }

                                switch(ar_nr_nonces[index].state) {
                                        case EMPTY: {
                                                // first nonce collect
                                                ar_nr_nonces[index].cuid = cuid;
                                                ar_nr_nonces[index].sector = cardAUTHSC;
                                                ar_nr_nonces[index].keytype = cardAUTHKEY;
                                                ar_nr_nonces[index].nonce = nonce;
                                                ar_nr_nonces[index].nr = nr;
                                                ar_nr_nonces[index].ar = ar;
                                                ar_nr_nonces[index].state = FIRST;
                                                break;
                                        } 
                                        case FIRST : { 
                                                // second nonce collect
                                                ar_nr_nonces[index].nonce2 = nonce;
                                                ar_nr_nonces[index].nr2 = nr;
                                                ar_nr_nonces[index].ar2 = ar;
                                                ar_nr_nonces[index].state = SECOND;

                                                // send to client
                                                cmd_send(CMD_ACK, CMD_SIMULATE_MIFARE_CARD, 0, 0, &ar_nr_nonces[index], sizeof(nonces_t));
                                                
                                                ar_nr_nonces[index].state = EMPTY;
                                                ar_nr_nonces[index].sector = 0;
                                                ar_nr_nonces[index].keytype = 0;
                                                
                                                moebius_count++;
                                                break;
                                        }
                                        default: break;
                                }
                        }
                        p_response = NULL;
                        
                } else if (receivedCmd[0] == MIFARE_ULC_AUTH_1 ) { // ULC authentication, or Desfire Authentication
                } else if (receivedCmd[0] == MIFARE_ULEV1_AUTH) { // NTAG / EV-1 authentication
                        if ( tagType == 7 ) {
                                uint16_t start = 13; // first 4 blocks of emu are [getversion answer - check tearing - pack - 0x00]
                                uint8_t emdata[4];
                                emlGetMemBt( emdata, start, 2);
                                AppendCrc14443a(emdata, 2);
                                EmSendCmdEx(emdata, sizeof(emdata), false);
                                p_response = NULL;
                                uint32_t pwd = bytes_to_num(receivedCmd+1,4);
                                
                                if ( MF_DBGLEVEL >= 3) Dbprintf("Auth attempt: %08x", pwd);     
                        }
                } else {
                        // Check for ISO 14443A-4 compliant commands, look at left nibble
                        switch (receivedCmd[0]) {
                                case 0x02:
                                case 0x03: {  // IBlock (command no CID)
                                        dynamic_response_info.response[0] = receivedCmd[0];
                                        dynamic_response_info.response[1] = 0x90;
                                        dynamic_response_info.response[2] = 0x00;
                                        dynamic_response_info.response_n = 3;
                                } break;
                                case 0x0B:
                                case 0x0A: { // IBlock (command CID)
                                  dynamic_response_info.response[0] = receivedCmd[0];
                                  dynamic_response_info.response[1] = 0x00;
                                  dynamic_response_info.response[2] = 0x90;
                                  dynamic_response_info.response[3] = 0x00;
                                  dynamic_response_info.response_n = 4;
                                } break;

                                case 0x1A:
                                case 0x1B: { // Chaining command
                                  dynamic_response_info.response[0] = 0xaa | ((receivedCmd[0]) & 1);
                                  dynamic_response_info.response_n = 2;
                                } break;

                                case 0xAA:
                                case 0xBB: {
                                  dynamic_response_info.response[0] = receivedCmd[0] ^ 0x11;
                                  dynamic_response_info.response_n = 2;
                                } break;
                                  
                                case 0xBA: { // ping / pong
                                        dynamic_response_info.response[0] = 0xAB;
                                        dynamic_response_info.response[1] = 0x00;
                                        dynamic_response_info.response_n = 2;
                                } break;

                                case 0xCA:
                                case 0xC2: { // Readers sends deselect command
                                        dynamic_response_info.response[0] = 0xCA;
                                        dynamic_response_info.response[1] = 0x00;
                                        dynamic_response_info.response_n = 2;
                                } break;

                                default: {
                                        // Never seen this command before
                                        LogTrace(receivedCmd, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        Dbprintf("Received unknown command (len=%d):",len);
                                        Dbhexdump(len,receivedCmd,false);
                                        // Do not respond
                                        dynamic_response_info.response_n = 0;
                                } break;
                        }
      
                        if (dynamic_response_info.response_n > 0) {
                                // Copy the CID from the reader query
                                dynamic_response_info.response[1] = receivedCmd[1];

                                // Add CRC bytes, always used in ISO 14443A-4 compliant cards
                                AppendCrc14443a(dynamic_response_info.response, dynamic_response_info.response_n);
                                dynamic_response_info.response_n += 2;
        
                                if (prepare_tag_modulation(&dynamic_response_info,DYNAMIC_MODULATION_BUFFER_SIZE) == false) {
                                        DbpString("Error preparing tag response");
                                        LogTrace(receivedCmd, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        break;
                                }
                                p_response = &dynamic_response_info;
                        }
                }

                // Count number of wakeups received after a halt
                if(order == 6 && lastorder == 5) { happened++; }

                // Count number of other messages after a halt
                if(order != 6 && lastorder == 5) { happened2++; }

                // comment this limit if you want to simulation longer          
                if (!tracing) {
                        DbpString("Trace Full. Simulation stopped.");
                        break;
                }
                // comment this limit if you want to simulation longer
                if(cmdsRecvd > 999) {
                        DbpString("1000 commands later...");
                        break;
                }
                cmdsRecvd++;

                if (p_response != NULL) {
                        EmSendCmd14443aRaw(p_response->modulation, p_response->modulation_n, receivedCmd[0] == 0x52);
                        // do the tracing for the previous reader request and this tag answer:
                        uint8_t par[MAX_PARITY_SIZE] = {0x00};
                        GetParity(p_response->response, p_response->response_n, par);
        
                        EmLogTrace(Uart.output, 
                                                Uart.len, 
                                                Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, 
                                                Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, 
                                                Uart.parity,
                                                p_response->response, 
                                                p_response->response_n,
                                                LastTimeProxToAirStart*16 + DELAY_ARM2AIR_AS_TAG,
                                                (LastTimeProxToAirStart + p_response->ProxToAirDuration)*16 + DELAY_ARM2AIR_AS_TAG, 
                                                par);
                }
        }

        FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
        set_tracing(FALSE);
        BigBuf_free_keep_EM();
        LED_A_OFF();

        if (MF_DBGLEVEL >= 4){
                Dbprintf("-[ Wake ups after halt  [%d]", happened);
                Dbprintf("-[ Messages after halt  [%d]", happened2);
                Dbprintf("-[ Num of received cmd  [%d]", cmdsRecvd);
                Dbprintf("-[ Num of moebius tries [%d]", moebius_count);
        }
        
        cmd_send(CMD_ACK,1,0,0,0,0);
}

// prepare a delayed transfer. This simply shifts ToSend[] by a number
// of bits specified in the delay parameter.
void PrepareDelayedTransfer(uint16_t delay) {
        delay &= 0x07;
        if (!delay) return;

        uint8_t bitmask = 0;
        uint8_t bits_to_shift = 0;
        uint8_t bits_shifted = 0;
        uint16_t i = 0;

        for (i = 0; i < delay; ++i)
                bitmask |= (0x01 << i);

        ToSend[++ToSendMax] = 0x00;

        for (i = 0; i < ToSendMax; ++i) {
                        bits_to_shift = ToSend[i] & bitmask;
                        ToSend[i] = ToSend[i] >> delay;
                        ToSend[i] = ToSend[i] | (bits_shifted << (8 - delay));
                        bits_shifted = bits_to_shift;
                }
        }


//-------------------------------------------------------------------------------------
// Transmit the command (to the tag) that was placed in ToSend[].
// Parameter timing:
// if NULL: transfer at next possible time, taking into account
//                      request guard time and frame delay time
// if == 0:     transfer immediately and return time of transfer
// if != 0: delay transfer until time specified
//-------------------------------------------------------------------------------------
static void TransmitFor14443a(const uint8_t *cmd, uint16_t len, uint32_t *timing) {
        FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_ISO14443A | FPGA_HF_ISO14443A_READER_MOD);

        uint32_t ThisTransferTime = 0;

        if (timing) {
                if(*timing == 0) {                                                                              // Measure time
                        *timing = (GetCountSspClk() + 8) & 0xfffffff8;
                } else {
                        PrepareDelayedTransfer(*timing & 0x00000007);           // Delay transfer (fine tuning - up to 7 MF clock ticks)
                }
                if(MF_DBGLEVEL >= 4 && GetCountSspClk() >= (*timing & 0xfffffff8)) Dbprintf("TransmitFor14443a: Missed timing");
                while(GetCountSspClk() < (*timing & 0xfffffff8));               // Delay transfer (multiple of 8 MF clock ticks)
                LastTimeProxToAirStart = *timing;
        } else {
                ThisTransferTime = ((MAX(NextTransferTime, GetCountSspClk()) & 0xfffffff8) + 8);

                while(GetCountSspClk() < ThisTransferTime);

                LastTimeProxToAirStart = ThisTransferTime;
        }
        
        // clear TXRDY
        AT91C_BASE_SSC->SSC_THR = SEC_Y;

        uint16_t c = 0;
        for(;;) {
                if(AT91C_BASE_SSC->SSC_SR & (AT91C_SSC_TXRDY)) {
                        AT91C_BASE_SSC->SSC_THR = cmd[c];
                        ++c;
                        if(c >= len)
                                break;
                }
        }
        
        NextTransferTime = MAX(NextTransferTime, LastTimeProxToAirStart + REQUEST_GUARD_TIME);
}

//-----------------------------------------------------------------------------
// Prepare reader command (in bits, support short frames) to send to FPGA
//-----------------------------------------------------------------------------
void CodeIso14443aBitsAsReaderPar(const uint8_t *cmd, uint16_t bits, const uint8_t *parity) {
        int i, j;
        int last = 0;
        uint8_t b;

        ToSendReset();

        // Start of Communication (Seq. Z)
        ToSend[++ToSendMax] = SEC_Z;
        LastProxToAirDuration = 8 * (ToSendMax+1) - 6;

        size_t bytecount = nbytes(bits);
        // Generate send structure for the data bits
        for (i = 0; i < bytecount; i++) {
                // Get the current byte to send
                b = cmd[i];
                size_t bitsleft = MIN((bits-(i*8)),8);

                for (j = 0; j < bitsleft; j++) {
                        if (b & 1) {
                                // Sequence X
                                ToSend[++ToSendMax] = SEC_X;
                                LastProxToAirDuration = 8 * (ToSendMax+1) - 2;
                                last = 1;
                        } else {
                                if (last == 0) {
                                // Sequence Z
                                ToSend[++ToSendMax] = SEC_Z;
                                LastProxToAirDuration = 8 * (ToSendMax+1) - 6;
                                } else {
                                        // Sequence Y
                                        ToSend[++ToSendMax] = SEC_Y;
                                        last = 0;
                                }
                        }
                        b >>= 1;
                }

                // Only transmit parity bit if we transmitted a complete byte
                if (j == 8 && parity != NULL) {
                        // Get the parity bit
                        if (parity[i>>3] & (0x80 >> (i&0x0007))) {
                                // Sequence X
                                ToSend[++ToSendMax] = SEC_X;
                                LastProxToAirDuration = 8 * (ToSendMax+1) - 2;
                                last = 1;
                        } else {
                                if (last == 0) {
                                        // Sequence Z
                                        ToSend[++ToSendMax] = SEC_Z;
                                        LastProxToAirDuration = 8 * (ToSendMax+1) - 6;
                                } else {
                                        // Sequence Y
                                        ToSend[++ToSendMax] = SEC_Y;
                                        last = 0;
                                }
                        }
                }
        }

        // End of Communication: Logic 0 followed by Sequence Y
        if (last == 0) {
                // Sequence Z
                ToSend[++ToSendMax] = SEC_Z;
                LastProxToAirDuration = 8 * (ToSendMax+1) - 6;
        } else {
                // Sequence Y
                ToSend[++ToSendMax] = SEC_Y;
                last = 0;
        }
        ToSend[++ToSendMax] = SEC_Y;

        // Convert to length of command:
        ++ToSendMax;
}

//-----------------------------------------------------------------------------
// Prepare reader command to send to FPGA
//-----------------------------------------------------------------------------
void CodeIso14443aAsReaderPar(const uint8_t *cmd, uint16_t len, const uint8_t *parity) {
  CodeIso14443aBitsAsReaderPar(cmd, len*8, parity);
}

//-----------------------------------------------------------------------------
// Wait for commands from reader
// Stop when button is pressed (return 1) or field was gone (return 2)
// Or return 0 when command is captured
//-----------------------------------------------------------------------------
int EmGetCmd(uint8_t *received, uint16_t *len, uint8_t *parity) {
        *len = 0;

        uint32_t timer = 0, vtime = 0;
        int analogCnt = 0;
        int analogAVG = 0;

        // Set FPGA mode to "simulated ISO 14443 tag", no modulation (listen
        // only, since we are receiving, not transmitting).
        // Signal field is off with the appropriate LED
        LED_D_OFF();
        FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_ISO14443A | FPGA_HF_ISO14443A_TAGSIM_LISTEN);

        // Set ADC to read field strength
        AT91C_BASE_ADC->ADC_CR = AT91C_ADC_SWRST;
        AT91C_BASE_ADC->ADC_MR =
                                ADC_MODE_PRESCALE(63) |
                                ADC_MODE_STARTUP_TIME(1) |
                                ADC_MODE_SAMPLE_HOLD_TIME(15);
        AT91C_BASE_ADC->ADC_CHER = ADC_CHANNEL(ADC_CHAN_HF);
        // start ADC
        AT91C_BASE_ADC->ADC_CR = AT91C_ADC_START;
        
        // Now run a 'software UART' on the stream of incoming samples.
        UartInit(received, parity);

        // Clear RXRDY:
    uint8_t b = (uint8_t)AT91C_BASE_SSC->SSC_RHR;
        
        for(;;) {
                WDT_HIT();

                if (BUTTON_PRESS()) return 1;

                // test if the field exists
                if (AT91C_BASE_ADC->ADC_SR & ADC_END_OF_CONVERSION(ADC_CHAN_HF)) {
                        analogCnt++;
                        analogAVG += AT91C_BASE_ADC->ADC_CDR[ADC_CHAN_HF];
                        AT91C_BASE_ADC->ADC_CR = AT91C_ADC_START;
                        if (analogCnt >= 32) {
                                if ((MAX_ADC_HF_VOLTAGE * (analogAVG / analogCnt) >> 10) < MF_MINFIELDV) {
                                        vtime = GetTickCount();
                                        if (!timer) timer = vtime;
                                        // 50ms no field --> card to idle state
                                        if (vtime - timer > 50) return 2;
                                } else
                                        if (timer) timer = 0;
                                analogCnt = 0;
                                analogAVG = 0;
                        }
                }

                // receive and test the miller decoding
        if(AT91C_BASE_SSC->SSC_SR & (AT91C_SSC_RXRDY)) {
            b = (uint8_t)AT91C_BASE_SSC->SSC_RHR;
                        if(MillerDecoding(b, 0)) {
                                *len = Uart.len;
                                return 0;
                        }
        }
        }
}

int EmSendCmd14443aRaw(uint8_t *resp, uint16_t respLen, bool correctionNeeded) {
        uint8_t b;
        uint16_t i = 0;
        uint32_t ThisTransferTime;
        
        // Modulate Manchester
        FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_ISO14443A | FPGA_HF_ISO14443A_TAGSIM_MOD);

        // include correction bit if necessary
        if (Uart.parityBits & 0x01) {
                correctionNeeded = TRUE;
        }
        // 1236, so correction bit needed
        i = (correctionNeeded) ? 0 : 1;

        // clear receiving shift register and holding register
        while(!(AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY));
        b = AT91C_BASE_SSC->SSC_RHR; (void) b;
        while(!(AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY));
        b = AT91C_BASE_SSC->SSC_RHR; (void) b;
        
        // wait for the FPGA to signal fdt_indicator == 1 (the FPGA is ready to queue new data in its delay line)
        for (uint8_t j = 0; j < 5; j++) {       // allow timeout - better late than never
                while(!(AT91C_BASE_SSC->SSC_SR & AT91C_SSC_RXRDY));
                if (AT91C_BASE_SSC->SSC_RHR) break;
        }

        while ((ThisTransferTime = GetCountSspClk()) & 0x00000007);

        // Clear TXRDY:
        AT91C_BASE_SSC->SSC_THR = SEC_F;

        // send cycle
        for(; i < respLen; ) {
                if(AT91C_BASE_SSC->SSC_SR & (AT91C_SSC_TXRDY)) {
                        AT91C_BASE_SSC->SSC_THR = resp[i++];
                        FpgaSendQueueDelay = (uint8_t)AT91C_BASE_SSC->SSC_RHR;
                }
        
                if(BUTTON_PRESS()) break;
        }

        // Ensure that the FPGA Delay Queue is empty before we switch to TAGSIM_LISTEN again:
        uint8_t fpga_queued_bits = FpgaSendQueueDelay >> 3;  // twich /8 ??   >>3, 
        for (i = 0; i <= fpga_queued_bits/8 + 1; ) {
                if(AT91C_BASE_SSC->SSC_SR & (AT91C_SSC_TXRDY)) {
                        AT91C_BASE_SSC->SSC_THR = SEC_F;
                        FpgaSendQueueDelay = (uint8_t)AT91C_BASE_SSC->SSC_RHR;
                        i++;
                }
        }
        LastTimeProxToAirStart = ThisTransferTime + (correctionNeeded?8:0);
        return 0;
}

int EmSend4bitEx(uint8_t resp, bool correctionNeeded){
        Code4bitAnswerAsTag(resp);
        int res = EmSendCmd14443aRaw(ToSend, ToSendMax, correctionNeeded);
        // do the tracing for the previous reader request and this tag answer:
        uint8_t par[1] = {0x00};
        GetParity(&resp, 1, par);
        EmLogTrace(Uart.output, 
                                Uart.len, 
                                Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, 
                                Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, 
                                Uart.parity,
                                &resp, 
                                1, 
                                LastTimeProxToAirStart*16 + DELAY_ARM2AIR_AS_TAG,
                                (LastTimeProxToAirStart + LastProxToAirDuration)*16 + DELAY_ARM2AIR_AS_TAG, 
                                par);
        return res;
}

int EmSend4bit(uint8_t resp){
        return EmSend4bitEx(resp, false);
}

int EmSendCmdExPar(uint8_t *resp, uint16_t respLen, bool correctionNeeded, uint8_t *par){
        CodeIso14443aAsTagPar(resp, respLen, par);
        int res = EmSendCmd14443aRaw(ToSend, ToSendMax, correctionNeeded);
        // do the tracing for the previous reader request and this tag answer:
        EmLogTrace(Uart.output, 
                                Uart.len, 
                                Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, 
                                Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, 
                                Uart.parity,
                                resp, 
                                respLen, 
                                LastTimeProxToAirStart*16 + DELAY_ARM2AIR_AS_TAG,
                                (LastTimeProxToAirStart + LastProxToAirDuration)*16 + DELAY_ARM2AIR_AS_TAG, 
                                par);
        return res;
}

int EmSendCmdEx(uint8_t *resp, uint16_t respLen, bool correctionNeeded){
        uint8_t par[MAX_PARITY_SIZE] = {0x00};
        GetParity(resp, respLen, par);
        return EmSendCmdExPar(resp, respLen, correctionNeeded, par);
}

int EmSendCmd(uint8_t *resp, uint16_t respLen){
        uint8_t par[MAX_PARITY_SIZE] = {0x00};
        GetParity(resp, respLen, par);
        return EmSendCmdExPar(resp, respLen, false, par);
}

int EmSendCmdPar(uint8_t *resp, uint16_t respLen, uint8_t *par){
        return EmSendCmdExPar(resp, respLen, false, par);
}

bool EmLogTrace(uint8_t *reader_data, uint16_t reader_len, uint32_t reader_StartTime, uint32_t reader_EndTime, uint8_t *reader_Parity,
                                 uint8_t *tag_data, uint16_t tag_len, uint32_t tag_StartTime, uint32_t tag_EndTime, uint8_t *tag_Parity)
{
        // we cannot exactly measure the end and start of a received command from reader. However we know that the delay from
        // end of the received command to start of the tag's (simulated by us) answer is n*128+20 or n*128+84 resp.
        // with n >= 9. The start of the tags answer can be measured and therefore the end of the received command be calculated:
        uint16_t reader_modlen = reader_EndTime - reader_StartTime;
        uint16_t approx_fdt = tag_StartTime - reader_EndTime;
        uint16_t exact_fdt = (approx_fdt - 20 + 32)/64 * 64 + 20;
        reader_EndTime = tag_StartTime - exact_fdt;
        reader_StartTime = reader_EndTime - reader_modlen;
                
        if (!LogTrace(reader_data, reader_len, reader_StartTime, reader_EndTime, reader_Parity, TRUE))
                return FALSE;
        else 
                return(!LogTrace(tag_data, tag_len, tag_StartTime, tag_EndTime, tag_Parity, FALSE));

}

//-----------------------------------------------------------------------------
// Wait a certain time for tag response
//  If a response is captured return TRUE
//  If it takes too long return FALSE
//-----------------------------------------------------------------------------
static int GetIso14443aAnswerFromTag(uint8_t *receivedResponse, uint8_t *receivedResponsePar, uint16_t offset) {
        uint32_t c = 0x00;
        
        // Set FPGA mode to "reader listen mode", no modulation (listen
        // only, since we are receiving, not transmitting).
        // Signal field is on with the appropriate LED
        LED_D_ON();
        FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_ISO14443A | FPGA_HF_ISO14443A_READER_LISTEN);
        
        // Now get the answer from the card
        DemodInit(receivedResponse, receivedResponsePar);

        // clear RXRDY:
    uint8_t b = (uint8_t)AT91C_BASE_SSC->SSC_RHR;

        for(;;) {
                WDT_HIT();

                if(AT91C_BASE_SSC->SSC_SR & (AT91C_SSC_RXRDY)) {
                        b = (uint8_t)AT91C_BASE_SSC->SSC_RHR;
                        if(ManchesterDecoding(b, offset, 0)) {
                                NextTransferTime = MAX(NextTransferTime, Demod.endTime - (DELAY_AIR2ARM_AS_READER + DELAY_ARM2AIR_AS_READER)/16 + FRAME_DELAY_TIME_PICC_TO_PCD);
                                return TRUE;
                        } else if (c++ > iso14a_timeout && Demod.state == DEMOD_UNSYNCD) {
                                return FALSE; 
                        }
                }
        }
}

void ReaderTransmitBitsPar(uint8_t* frame, uint16_t bits, uint8_t *par, uint32_t *timing) {

        CodeIso14443aBitsAsReaderPar(frame, bits, par);
        // Send command to tag
        TransmitFor14443a(ToSend, ToSendMax, timing);
        if(trigger) LED_A_ON();
  
        LogTrace(frame, nbytes(bits), (LastTimeProxToAirStart<<4) + DELAY_ARM2AIR_AS_READER, ((LastTimeProxToAirStart + LastProxToAirDuration)<<4) + DELAY_ARM2AIR_AS_READER, par, TRUE);
}

void ReaderTransmitPar(uint8_t* frame, uint16_t len, uint8_t *par, uint32_t *timing) {
  ReaderTransmitBitsPar(frame, len*8, par, timing);
}

void ReaderTransmitBits(uint8_t* frame, uint16_t len, uint32_t *timing) {
        // Generate parity and redirect
        uint8_t par[MAX_PARITY_SIZE] = {0x00};
        GetParity(frame, len/8, par);  
        ReaderTransmitBitsPar(frame, len, par, timing);
}

void ReaderTransmit(uint8_t* frame, uint16_t len, uint32_t *timing) {
        // Generate parity and redirect
        uint8_t par[MAX_PARITY_SIZE] = {0x00};
        GetParity(frame, len, par);
        ReaderTransmitBitsPar(frame, len*8, par, timing);
}

int ReaderReceiveOffset(uint8_t* receivedAnswer, uint16_t offset, uint8_t *parity) {
        if (!GetIso14443aAnswerFromTag(receivedAnswer, parity, offset))
                return FALSE;
        LogTrace(receivedAnswer, Demod.len, Demod.startTime*16 - DELAY_AIR2ARM_AS_READER, Demod.endTime*16 - DELAY_AIR2ARM_AS_READER, parity, FALSE);
        return Demod.len;
}

int ReaderReceive(uint8_t *receivedAnswer, uint8_t *parity) {
        if (!GetIso14443aAnswerFromTag(receivedAnswer, parity, 0))
                return FALSE;
        LogTrace(receivedAnswer, Demod.len, Demod.startTime*16 - DELAY_AIR2ARM_AS_READER, Demod.endTime*16 - DELAY_AIR2ARM_AS_READER, parity, FALSE);
        return Demod.len;
}

// performs iso14443a anticollision (optional) and card select procedure
// fills the uid and cuid pointer unless NULL
// fills the card info record unless NULL
// if anticollision is false, then the UID must be provided in uid_ptr[] 
// and num_cascades must be set (1: 4 Byte UID, 2: 7 Byte UID, 3: 10 Byte UID)
int iso14443a_select_card(byte_t *uid_ptr, iso14a_card_select_t *p_hi14a_card, uint32_t *cuid_ptr, bool anticollision, uint8_t num_cascades) {
        uint8_t wupa[]       = { ISO14443A_CMD_WUPA };  // 0x26 - ISO14443A_CMD_REQA  0x52 - ISO14443A_CMD_WUPA
        uint8_t sel_all[]    = { ISO14443A_CMD_ANTICOLL_OR_SELECT,0x20 };
        uint8_t sel_uid[]    = { ISO14443A_CMD_ANTICOLL_OR_SELECT,0x70,0x00,0x00,0x00,0x00,0x00,0x00,0x00};
        uint8_t rats[]       = { ISO14443A_CMD_RATS,0x80,0x00,0x00 }; // FSD=256, FSDI=8, CID=0
        uint8_t resp[MAX_FRAME_SIZE] = {0}; // theoretically. A usual RATS will be much smaller
        uint8_t resp_par[MAX_PARITY_SIZE] = {0};
        byte_t uid_resp[4] = {0};
        size_t uid_resp_len = 0;

        uint8_t sak = 0x04; // cascade uid
        int cascade_level = 0;
        int len;

        // Broadcast for a card, WUPA (0x52) will force response from all cards in the field
    ReaderTransmitBitsPar(wupa, 7, NULL, NULL);
        
        // Receive the ATQA
        if(!ReaderReceive(resp, resp_par)) return 0;

        if(p_hi14a_card) {
                memcpy(p_hi14a_card->atqa, resp, 2);
                p_hi14a_card->uidlen = 0;
                memset(p_hi14a_card->uid,0,10);
        }

        if (anticollision) {
                // clear uid
                if (uid_ptr)
                        memset(uid_ptr,0,10);
        }

        // reset the PCB block number
        iso14_pcb_blocknum = 0;
        
        // check for proprietary anticollision:
        if ((resp[0] & 0x1F) == 0) return 3;
        
        // OK we will select at least at cascade 1, lets see if first byte of UID was 0x88 in
        // which case we need to make a cascade 2 request and select - this is a long UID
        // While the UID is not complete, the 3nd bit (from the right) is set in the SAK.
        for(; sak & 0x04; cascade_level++) {
                // SELECT_* (L1: 0x93, L2: 0x95, L3: 0x97)
                sel_uid[0] = sel_all[0] = 0x93 + cascade_level * 2;

                if (anticollision) {
                // SELECT_ALL
                        ReaderTransmit(sel_all, sizeof(sel_all), NULL);
                        if (!ReaderReceive(resp, resp_par)) return 0;

                        if (Demod.collisionPos) {                       // we had a collision and need to construct the UID bit by bit
                                memset(uid_resp, 0, 4);
                                uint16_t uid_resp_bits = 0;
                                uint16_t collision_answer_offset = 0;
                                // anti-collision-loop:
                                while (Demod.collisionPos) {
                                        Dbprintf("Multiple tags detected. Collision after Bit %d", Demod.collisionPos);
                                        for (uint16_t i = collision_answer_offset; i < Demod.collisionPos; i++, uid_resp_bits++) {      // add valid UID bits before collision point
                                                uint16_t UIDbit = (resp[i/8] >> (i % 8)) & 0x01;
                                                uid_resp[uid_resp_bits / 8] |= UIDbit << (uid_resp_bits % 8);
                                        }
                                        uid_resp[uid_resp_bits/8] |= 1 << (uid_resp_bits % 8);                                  // next time select the card(s) with a 1 in the collision position
                                        uid_resp_bits++;
                                        // construct anticollosion command:
                                        sel_uid[1] = ((2 + uid_resp_bits/8) << 4) | (uid_resp_bits & 0x07);     // length of data in bytes and bits
                                        for (uint16_t i = 0; i <= uid_resp_bits/8; i++) {
                                                sel_uid[2+i] = uid_resp[i];
                                        }
                                        collision_answer_offset = uid_resp_bits%8;
                                        ReaderTransmitBits(sel_uid, 16 + uid_resp_bits, NULL);
                                        if (!ReaderReceiveOffset(resp, collision_answer_offset, resp_par)) return 0;
                                }
                                // finally, add the last bits and BCC of the UID
                                for (uint16_t i = collision_answer_offset; i < (Demod.len-1)*8; i++, uid_resp_bits++) {
                                        uint16_t UIDbit = (resp[i/8] >> (i%8)) & 0x01;
                                        uid_resp[uid_resp_bits/8] |= UIDbit << (uid_resp_bits % 8);
                                }

                        } else {                // no collision, use the response to SELECT_ALL as current uid
                                memcpy(uid_resp, resp, 4);
                        }
                        
                } else {
                        if (cascade_level < num_cascades - 1) {
                                uid_resp[0] = 0x88;
                                memcpy(uid_resp+1, uid_ptr+cascade_level*3, 3);
                        } else {
                                memcpy(uid_resp, uid_ptr+cascade_level*3, 4);
                        }
                }
                uid_resp_len = 4;

                // calculate crypto UID. Always use last 4 Bytes.
                if(cuid_ptr)
                        *cuid_ptr = bytes_to_num(uid_resp, 4);

                // Construct SELECT UID command
                sel_uid[1] = 0x70;                                                                                                      // transmitting a full UID (1 Byte cmd, 1 Byte NVB, 4 Byte UID, 1 Byte BCC, 2 Bytes CRC)
                memcpy(sel_uid+2, uid_resp, 4);                                                                         // the UID received during anticollision, or the provided UID
                sel_uid[6] = sel_uid[2] ^ sel_uid[3] ^ sel_uid[4] ^ sel_uid[5];         // calculate and add BCC
                AppendCrc14443a(sel_uid, 7);                                                                            // calculate and add CRC
                ReaderTransmit(sel_uid, sizeof(sel_uid), NULL);

                // Receive the SAK
                if (!ReaderReceive(resp, resp_par)) return 0;
                
                sak = resp[0];

                // Test if more parts of the uid are coming
                if ((sak & 0x04) /* && uid_resp[0] == 0x88 */) {
                        // Remove first byte, 0x88 is not an UID byte, it CT, see page 3 of:
                        // http://www.nxp.com/documents/application_note/AN10927.pdf
                        uid_resp[0] = uid_resp[1];
                        uid_resp[1] = uid_resp[2];
                        uid_resp[2] = uid_resp[3]; 
                        uid_resp_len = 3;
                }

                if(uid_ptr && anticollision)
                        memcpy(uid_ptr + (cascade_level*3), uid_resp, uid_resp_len);

                if(p_hi14a_card) {
                        memcpy(p_hi14a_card->uid + (cascade_level*3), uid_resp, uid_resp_len);
                        p_hi14a_card->uidlen += uid_resp_len;
                }
        }

        if(p_hi14a_card) {
                p_hi14a_card->sak = sak;
                p_hi14a_card->ats_len = 0;
        }

        // non iso14443a compliant tag
        if( (sak & 0x20) == 0) return 2; 

        // Request for answer to select
        AppendCrc14443a(rats, 2);
        ReaderTransmit(rats, sizeof(rats), NULL);

        if (!(len = ReaderReceive(resp, resp_par))) return 0;
        
        if(p_hi14a_card) {
                memcpy(p_hi14a_card->ats, resp, sizeof(p_hi14a_card->ats));
                p_hi14a_card->ats_len = len;
        }

        // set default timeout based on ATS
        iso14a_set_ATS_timeout(resp);
        return 1;       
}

void iso14443a_setup(uint8_t fpga_minor_mode) {

        FpgaDownloadAndGo(FPGA_BITSTREAM_HF);
        // Set up the synchronous serial port
        FpgaSetupSsc();
        // connect Demodulated Signal to ADC:
        SetAdcMuxFor(GPIO_MUXSEL_HIPKD);

        LED_D_OFF();
        // Signal field is on with the appropriate LED
        if (fpga_minor_mode == FPGA_HF_ISO14443A_READER_MOD ||
                fpga_minor_mode == FPGA_HF_ISO14443A_READER_LISTEN)
                LED_D_ON();

        FpgaWriteConfWord(FPGA_MAJOR_MODE_HF_ISO14443A | fpga_minor_mode);

        SpinDelay(20);
        
        // Start the timer
        StartCountSspClk();
        
        // Prepare the demodulation functions
        DemodReset();
        UartReset();
        NextTransferTime = 2 * DELAY_ARM2AIR_AS_READER;
        iso14a_set_timeout(10*106); // 20ms default     
}

int iso14_apdu(uint8_t *cmd, uint16_t cmd_len, void *data) {
        uint8_t parity[MAX_PARITY_SIZE] = {0x00};
        uint8_t real_cmd[cmd_len+4];
        real_cmd[0] = 0x0a; //I-Block
        // put block number into the PCB
        real_cmd[0] |= iso14_pcb_blocknum;
        real_cmd[1] = 0x00; //CID: 0 //FIXME: allow multiple selected cards
        memcpy(real_cmd+2, cmd, cmd_len);
        AppendCrc14443a(real_cmd,cmd_len+2);
 
        ReaderTransmit(real_cmd, cmd_len+4, NULL);
        size_t len = ReaderReceive(data, parity);
         //DATA LINK ERROR
        if (!len) return 0;
        
        uint8_t *data_bytes = (uint8_t *) data;

        // if we received an I- or R(ACK)-Block with a block number equal to the
        // current block number, toggle the current block number
        if (len >= 4 // PCB+CID+CRC = 4 bytes
                 && ((data_bytes[0] & 0xC0) == 0 // I-Block
                     || (data_bytes[0] & 0xD0) == 0x80) // R-Block with ACK bit set to 0
                 && (data_bytes[0] & 0x01) == iso14_pcb_blocknum) // equal block numbers
        {
                iso14_pcb_blocknum ^= 1;
        }
        return len;
}


//-----------------------------------------------------------------------------
// Read an ISO 14443a tag. Send out commands and store answers.
//-----------------------------------------------------------------------------
void ReaderIso14443a(UsbCommand *c) {
        iso14a_command_t param = c->arg[0];
        size_t len = c->arg[1] & 0xffff;
        size_t lenbits = c->arg[1] >> 16;
        uint32_t timeout = c->arg[2];
        uint8_t *cmd = c->d.asBytes;
        uint32_t arg0 = 0;
        byte_t buf[USB_CMD_DATA_SIZE] = {0x00};
        uint8_t par[MAX_PARITY_SIZE] = {0x00};
  
        if (param & ISO14A_CONNECT)
                clear_trace();

        set_tracing(TRUE);

        if (param & ISO14A_REQUEST_TRIGGER)
                iso14a_set_trigger(TRUE);

        if (param & ISO14A_CONNECT) {
                iso14443a_setup(FPGA_HF_ISO14443A_READER_LISTEN);
                if(!(param & ISO14A_NO_SELECT)) {
                        iso14a_card_select_t *card = (iso14a_card_select_t*)buf;
                        arg0 = iso14443a_select_card(NULL,card,NULL, true, 0);
                        cmd_send(CMD_ACK, arg0, card->uidlen, 0, buf, sizeof(iso14a_card_select_t));
                        // if it fails,  the cmdhf14a.c client quites.. however this one still executes.
                        if ( arg0 == 0 ) return;
                }
        }

        if (param & ISO14A_SET_TIMEOUT)
                iso14a_set_timeout(timeout);

        if (param & ISO14A_APDU) {
                arg0 = iso14_apdu(cmd, len, buf);
                cmd_send(CMD_ACK,arg0,0,0,buf,sizeof(buf));
        }

        if (param & ISO14A_RAW) {
                if (param & ISO14A_APPEND_CRC) {
                        if (param & ISO14A_TOPAZMODE)
                                AppendCrc14443b(cmd,len);
                        else
                                AppendCrc14443a(cmd,len);
                        
                        len += 2;
                        if (lenbits) lenbits += 16;
                }
                if (lenbits>0) {                                // want to send a specific number of bits (e.g. short commands)
                        if (param & ISO14A_TOPAZMODE) {
                                int bits_to_send = lenbits;
                                uint16_t i = 0;
                                ReaderTransmitBitsPar(&cmd[i++], MIN(bits_to_send, 7), NULL, NULL);             // first byte is always short (7bits) and no parity
                                bits_to_send -= 7;
                                while (bits_to_send > 0) {
                                        ReaderTransmitBitsPar(&cmd[i++], MIN(bits_to_send, 8), NULL, NULL);     // following bytes are 8 bit and no parity
                                        bits_to_send -= 8;
                                }
                        } else {
                        GetParity(cmd, lenbits/8, par);
                                ReaderTransmitBitsPar(cmd, lenbits, par, NULL);                                                 // bytes are 8 bit with odd parity
                        }
                } else {                                        // want to send complete bytes only
                        if (param & ISO14A_TOPAZMODE) {
                                uint16_t i = 0;
                                ReaderTransmitBitsPar(&cmd[i++], 7, NULL, NULL);                                                // first byte: 7 bits, no paritiy
                                while (i < len) {
                                        ReaderTransmitBitsPar(&cmd[i++], 8, NULL, NULL);                                        // following bytes: 8 bits, no paritiy
                                }
                } else {
                                ReaderTransmit(cmd,len, NULL);                                                                                  // 8 bits, odd parity
                        }
                }
                arg0 = ReaderReceive(buf, par);
                cmd_send(CMD_ACK,arg0,0,0,buf,sizeof(buf));
        }

        if (param & ISO14A_REQUEST_TRIGGER)
                iso14a_set_trigger(FALSE);

        if (param & ISO14A_NO_DISCONNECT)
                return;

        FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
        set_tracing(FALSE);
        LEDsoff();
}

// Determine the distance between two nonces.
// Assume that the difference is small, but we don't know which is first.
// Therefore try in alternating directions.
int32_t dist_nt(uint32_t nt1, uint32_t nt2) {

        if (nt1 == nt2) return 0;
        
        uint32_t nttmp1 = nt1;
        uint32_t nttmp2 = nt2;

        // 0xFFFF -- Half up and half down to find distance between nonces
        for (uint16_t i = 1; i < 32768/8; i += 8) {
                nttmp1 = prng_successor(nttmp1, 1);     if (nttmp1 == nt2) return i;
                nttmp1 = prng_successor(nttmp1, 1);     if (nttmp1 == nt2) return i+1;
                nttmp1 = prng_successor(nttmp1, 1);     if (nttmp1 == nt2) return i+2;
                nttmp1 = prng_successor(nttmp1, 1);     if (nttmp1 == nt2) return i+3;
                nttmp1 = prng_successor(nttmp1, 1);     if (nttmp1 == nt2) return i+4;
                nttmp1 = prng_successor(nttmp1, 1);     if (nttmp1 == nt2) return i+5;
                nttmp1 = prng_successor(nttmp1, 1);     if (nttmp1 == nt2) return i+6;
                nttmp1 = prng_successor(nttmp1, 1);     if (nttmp1 == nt2) return i+7;
                
                nttmp2 = prng_successor(nttmp2, 1);     if (nttmp2 == nt1) return -i;
                nttmp2 = prng_successor(nttmp2, 1);     if (nttmp2 == nt1) return -(i+1);
                nttmp2 = prng_successor(nttmp2, 1);     if (nttmp2 == nt1) return -(i+2);
                nttmp2 = prng_successor(nttmp2, 1);     if (nttmp2 == nt1) return -(i+3);
                nttmp2 = prng_successor(nttmp2, 1);     if (nttmp2 == nt1) return -(i+4);
                nttmp2 = prng_successor(nttmp2, 1);     if (nttmp2 == nt1) return -(i+5);
                nttmp2 = prng_successor(nttmp2, 1);     if (nttmp2 == nt1) return -(i+6);
                nttmp2 = prng_successor(nttmp2, 1);     if (nttmp2 == nt1) return -(i+7);               
        }
        // either nt1 or nt2 are invalid nonces 
        return(-99999); 
}

//-----------------------------------------------------------------------------
// Recover several bits of the cypher stream. This implements (first stages of)
// the algorithm described in "The Dark Side of Security by Obscurity and
// Cloning MiFare Classic Rail and Building Passes, Anywhere, Anytime"
// (article by Nicolas T. Courtois, 2009)
//-----------------------------------------------------------------------------

void ReaderMifare(bool first_try, uint8_t block, uint8_t keytype ) {
        
        uint8_t mf_auth[]       = { keytype, block, 0x00, 0x00 };
        uint8_t mf_nr_ar[]      = { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 };
        uint8_t uid[10]         = {0,0,0,0,0,0,0,0,0,0};
        uint8_t par_list[8]     = {0,0,0,0,0,0,0,0};
        uint8_t ks_list[8]      = {0,0,0,0,0,0,0,0};
        uint8_t receivedAnswer[MAX_MIFARE_FRAME_SIZE] = {0x00};
        uint8_t receivedAnswerPar[MAX_MIFARE_PARITY_SIZE] = {0x00};
        uint8_t par[1] = {0};   // maximum 8 Bytes to be sent here, 1 byte parity is therefore enough
        byte_t nt_diff = 0;
        uint32_t nt = 0;
        uint32_t previous_nt = 0;       
        uint32_t cuid = 0;
        
        int32_t catch_up_cycles = 0;
        int32_t last_catch_up = 0;
        int32_t isOK = 0;
        int32_t nt_distance = 0;
        
        uint16_t elapsed_prng_sequences = 1;
        uint16_t consecutive_resyncs = 0;
        uint16_t unexpected_random = 0;
        uint16_t sync_tries = 0;

        // static variables here, is re-used in the next call
        static uint32_t nt_attacked = 0;
        static uint32_t sync_time = 0;
        static uint32_t sync_cycles = 0;
        static uint8_t par_low = 0;
        static uint8_t mf_nr_ar3 = 0;
        
        #define PRNG_SEQUENCE_LENGTH    (1 << 16)
        #define MAX_UNEXPECTED_RANDOM   4               // maximum number of unexpected (i.e. real) random numbers when trying to sync. Then give up.
        #define MAX_SYNC_TRIES          32
        
        AppendCrc14443a(mf_auth, 2);
        
        BigBuf_free(); BigBuf_Clear_ext(false); 
        clear_trace();
        set_tracing(FALSE);     
        iso14443a_setup(FPGA_HF_ISO14443A_READER_MOD);

        sync_time = GetCountSspClk() & 0xfffffff8;
        sync_cycles = PRNG_SEQUENCE_LENGTH; // Mifare Classic's random generator repeats every 2^16 cycles (and so do the nonces).              
        nt_attacked = 0;
        
   if (MF_DBGLEVEL >= 4)        Dbprintf("Mifare::Sync %u", sync_time);
                                
        if (first_try) {
                mf_nr_ar3 = 0;
                par_low = 0;
        } else {
                // we were unsuccessful on a previous call. 
                // Try another READER nonce (first 3 parity bits remain the same)
                ++mf_nr_ar3;
                mf_nr_ar[3] = mf_nr_ar3;
                par[0] = par_low;
        }

        bool have_uid = FALSE;
        uint8_t cascade_levels = 0;

        LED_C_ON(); 
        uint16_t i;
        for(i = 0; TRUE; ++i) {

                WDT_HIT();

                // Test if the action was cancelled
                if(BUTTON_PRESS()) {
                        isOK = -1;
                        break;
                }
                
                // this part is from Piwi's faster nonce collecting part in Hardnested.
                if (!have_uid) { // need a full select cycle to get the uid first
                        iso14a_card_select_t card_info;         
                        if(!iso14443a_select_card(uid, &card_info, &cuid, true, 0)) {
                                if (MF_DBGLEVEL >= 4)   Dbprintf("Mifare: Can't select card (ALL)");
                                break;
                        }
                        switch (card_info.uidlen) {
                                case 4 : cascade_levels = 1; break;
                                case 7 : cascade_levels = 2; break;
                                case 10: cascade_levels = 3; break;
                                default: break;
                        }
                        have_uid = TRUE;        
                } else { // no need for anticollision. We can directly select the card
                        if(!iso14443a_select_card(uid, NULL, &cuid, false, cascade_levels)) {
                                if (MF_DBGLEVEL >= 4)   Dbprintf("Mifare: Can't select card (UID)");
                                continue;
                        }
                }
                
                // Sending timeslot of ISO14443a frame          
                sync_time = (sync_time & 0xfffffff8 ) + sync_cycles + catch_up_cycles;
                catch_up_cycles = 0;
                                                                
                // if we missed the sync time already, advance to the next nonce repeat
                while( GetCountSspClk() > sync_time) {
                        ++elapsed_prng_sequences;
                        sync_time = (sync_time & 0xfffffff8 ) + sync_cycles;
                }               

                // Transmit MIFARE_CLASSIC_AUTH at synctime. Should result in returning the same tag nonce (== nt_attacked)
                ReaderTransmit(mf_auth, sizeof(mf_auth), &sync_time);

                // Receive the (4 Byte) "random" nonce from TAG
                if (!ReaderReceive(receivedAnswer, receivedAnswerPar))
                        continue;

                previous_nt = nt;
                nt = bytes_to_num(receivedAnswer, 4);
                
                // Transmit reader nonce with fake par
                ReaderTransmitPar(mf_nr_ar, sizeof(mf_nr_ar), par, NULL);
        
                // we didn't calibrate our clock yet,
                // iceman: has to be calibrated every time.
                if (previous_nt && !nt_attacked) { 

                        nt_distance = dist_nt(previous_nt, nt);
                        
                        // if no distance between,  then we are in sync.
                        if (nt_distance == 0) {
                                nt_attacked = nt;
                        } else {
                                if (nt_distance == -99999) { // invalid nonce received
                                        ++unexpected_random;
                                        if (unexpected_random > MAX_UNEXPECTED_RANDOM) {
                                                isOK = -3;              // Card has an unpredictable PRNG. Give up      
                                                break;
                                        } else {                                                
                                                if (sync_cycles <= 0) sync_cycles += PRNG_SEQUENCE_LENGTH;
                                                LED_B_OFF();
                                                continue;               // continue trying...
                                        }
                                }
                                
                                if (++sync_tries > MAX_SYNC_TRIES) {
                                        isOK = -4;                      // Card's PRNG runs at an unexpected frequency or resets unexpectedly
                                        break;
                                }
                                
                                sync_cycles = (sync_cycles - nt_distance)/elapsed_prng_sequences;
                                
                                if (sync_cycles <= 0)
                                        sync_cycles += PRNG_SEQUENCE_LENGTH;
                                
                                if (MF_DBGLEVEL >= 4)
                                        Dbprintf("calibrating in cycle %d. nt_distance=%d, elapsed_prng_sequences=%d, new sync_cycles: %d\n", i, nt_distance, elapsed_prng_sequences, sync_cycles);

                                LED_B_OFF();
                                continue;
                        }
                }
                LED_B_OFF();

                if ( (nt != nt_attacked) && nt_attacked) {      // we somehow lost sync. Try to catch up again...
                        
                        catch_up_cycles = ABS(dist_nt(nt_attacked, nt));
                        if (catch_up_cycles == 99999) {                 // invalid nonce received. Don't resync on that one.
                                catch_up_cycles = 0;
                                continue;
                        }               
                        // average? 
                        catch_up_cycles /= elapsed_prng_sequences;
                
                        if (catch_up_cycles == last_catch_up) {
                                ++consecutive_resyncs;
                        } else {
                                last_catch_up = catch_up_cycles;
                            consecutive_resyncs = 0;
                        }               
                        
                        if (consecutive_resyncs < 3) {
                                if (MF_DBGLEVEL >= 4)
                                        Dbprintf("Lost sync in cycle %d. nt_distance=%d. Consecutive Resyncs = %d. Trying one time catch up...\n", i, catch_up_cycles, consecutive_resyncs);
                        } else {        
                                sync_cycles += catch_up_cycles;
                                
                                if (MF_DBGLEVEL >= 4) 
                                        Dbprintf("Lost sync in cycle %d for the fourth time consecutively (nt_distance = %d). Adjusting sync_cycles to %d.\n", i, catch_up_cycles, sync_cycles);

                                last_catch_up = 0;
                                catch_up_cycles = 0;
                                consecutive_resyncs = 0;
                        }
                        continue;
                }
 
                // Receive answer. This will be a 4 Bit NACK when the 8 parity bits are OK after decoding
                if (ReaderReceive(receivedAnswer, receivedAnswerPar)) {
                        catch_up_cycles = 8;    // the PRNG is delayed by 8 cycles due to the NAC (4Bits = 0x05 encrypted) transfer
        
                        if (nt_diff == 0)
                                par_low = par[0] & 0xE0; // there is no need to check all parities for other nt_diff. Parity Bits for mf_nr_ar[0..2] won't change

                        par_list[nt_diff] = SwapBits(par[0], 8);
                        ks_list[nt_diff] = receivedAnswer[0] ^ 0x05;  // xor with NACK value to get keystream

                        // Test if the information is complete
                        if (nt_diff == 0x07) {
                                isOK = 1;
                                break;
                        }

                        nt_diff = (nt_diff + 1) & 0x07;
                        mf_nr_ar[3] = (mf_nr_ar[3] & 0x1F) | (nt_diff << 5);
                        par[0] = par_low;
                        
                } else {
                        // No NACK.     
                        if (nt_diff == 0 && first_try) {
                                par[0]++;
                                if (par[0] == 0x00) {   // tried all 256 possible parities without success. Card doesn't send NACK.
                                        isOK = -2;
                                        break;
                                }
                        } else {
                                // Why this?
                                par[0] = ((par[0] & 0x1F) + 1) | par_low;
                        }
                }
                
                // reset the resyncs since we got a complete transaction on right time.
                consecutive_resyncs = 0;
        } // end for loop

        mf_nr_ar[3] &= 0x1F;

        if (MF_DBGLEVEL >= 4) Dbprintf("Number of sent auth requestes: %u", i);
        
        uint8_t buf[28] = {0x00};
        memset(buf, 0x00, sizeof(buf));
        num_to_bytes(cuid, 4, buf);
        num_to_bytes(nt, 4, buf + 4);
        memcpy(buf + 8,  par_list, 8);
        memcpy(buf + 16, ks_list, 8);
        memcpy(buf + 24, mf_nr_ar, 4);
                
        cmd_send(CMD_ACK, isOK, 0, 0, buf, sizeof(buf) );

        FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
        LEDsoff();
        set_tracing(FALSE);
}


/**
  *MIFARE 1K simulate.
  *
  *@param flags :
  *     FLAG_INTERACTIVE                - In interactive mode, we are expected to finish the operation with an ACK
  * FLAG_4B_UID_IN_DATA         - use 4-byte UID in the data-section
  * FLAG_7B_UID_IN_DATA         - use 7-byte UID in the data-section
  * FLAG_10B_UID_IN_DATA        - use 10-byte UID in the data-section
  * FLAG_UID_IN_EMUL            - use 4-byte UID from emulator memory
  *     FLAG_NR_AR_ATTACK               - collect NR_AR responses for bruteforcing later
  *@param exitAfterNReads, exit simulation after n blocks have been read, 0 is inifite
  */
void Mifare1ksim(uint8_t flags, uint8_t exitAfterNReads, uint8_t arg2, uint8_t *datain) {

        // init pseudorand
        fast_prand( GetTickCount() );
        
        int cardSTATE = MFEMUL_NOFIELD;
        int _UID_LEN = 0;  // 4, 7, 10
        int vHf = 0;    // in mV
        int res = 0;
        uint32_t selTimer = 0;
        uint32_t authTimer = 0;
        uint16_t len = 0;
        uint8_t cardWRBL = 0;
        uint8_t cardAUTHSC = 0;
        uint8_t cardAUTHKEY = 0xff;  // no authentication
        uint32_t cuid = 0;
        uint32_t ans = 0;
        uint32_t cardINTREG = 0;
        uint8_t cardINTBLOCK = 0;
        struct Crypto1State mpcs = {0, 0};
        struct Crypto1State *pcs;
        pcs = &mpcs;
        uint32_t numReads = 0;  // Counts numer of times reader read a block
        uint8_t receivedCmd[MAX_MIFARE_FRAME_SIZE] = {0x00};
        uint8_t receivedCmd_par[MAX_MIFARE_PARITY_SIZE] = {0x00};
        uint8_t response[MAX_MIFARE_FRAME_SIZE] = {0x00};
        uint8_t response_par[MAX_MIFARE_PARITY_SIZE] = {0x00};
        
        uint8_t atqa[]   = {0x04, 0x00}; // Mifare classic 1k
        uint8_t sak_4[]  = {0x0C, 0x00, 0x00}; // CL1 - 4b uid
        uint8_t sak_7[]  = {0x0C, 0x00, 0x00}; // CL2 - 7b uid
        uint8_t sak_10[] = {0x0C, 0x00, 0x00}; // CL3 - 10b uid
        // uint8_t sak[] = {0x09, 0x3f, 0xcc };  // Mifare Mini 
        
        uint8_t rUIDBCC1[] = {0xde, 0xad, 0xbe, 0xaf, 0x62}; 
        uint8_t rUIDBCC2[] = {0xde, 0xad, 0xbe, 0xaf, 0x62}; 
        uint8_t rUIDBCC3[] = {0xde, 0xad, 0xbe, 0xaf, 0x62};

        // TAG Nonce - Authenticate response
        uint8_t rAUTH_NT[4];
        uint32_t nonce = prand();
        num_to_bytes(nonce, 4, rAUTH_NT);
        
        // uint8_t rAUTH_NT[] = {0x55, 0x41, 0x49, 0x92};// nonce from nested? why this?
        uint8_t rAUTH_AT[] = {0x00, 0x00, 0x00, 0x00};
        
        // Here, we collect CUID, NT, NR, AR, CUID2, NT2, NR2, AR2
        // This can be used in a reader-only attack.
        nonces_t ar_nr_nonces[ATTACK_KEY_COUNT];
        memset(ar_nr_nonces, 0x00, sizeof(ar_nr_nonces));

        // -- Determine the UID
        // Can be set from emulator memory or incoming data
        // Length: 4,7,or 10 bytes
        if ( (flags & FLAG_UID_IN_EMUL) == FLAG_UID_IN_EMUL)
                emlGetMemBt(datain, 0, 10);  // load 10bytes from EMUL to the datain pointer. to be used below.
        
        if ( (flags & FLAG_4B_UID_IN_DATA) == FLAG_4B_UID_IN_DATA) {
                memcpy(rUIDBCC1, datain, 4);
                _UID_LEN = 4;
        } else if ( (flags & FLAG_7B_UID_IN_DATA) == FLAG_7B_UID_IN_DATA) {
                memcpy(&rUIDBCC1[1], datain,   3);
                memcpy( rUIDBCC2,    datain+3, 4);
                _UID_LEN = 7;
        } else if ( (flags & FLAG_10B_UID_IN_DATA) == FLAG_10B_UID_IN_DATA) {
                memcpy(&rUIDBCC1[1], datain,   3);
                memcpy(&rUIDBCC2[1], datain+3, 3);
                memcpy( rUIDBCC3,    datain+6, 4);
                _UID_LEN = 10;
        }

        switch (_UID_LEN) {
                case 4:
                        sak_4[0] &= 0xFB;               
                        // save CUID
                        cuid = bytes_to_num(rUIDBCC1, 4);
                        // BCC
                        rUIDBCC1[4] = rUIDBCC1[0] ^ rUIDBCC1[1] ^ rUIDBCC1[2] ^ rUIDBCC1[3];
                        if (MF_DBGLEVEL >= 2)   {
                                Dbprintf("4B UID: %02x%02x%02x%02x", 
                                        rUIDBCC1[0],
                                        rUIDBCC1[1],
                                        rUIDBCC1[2],
                                        rUIDBCC1[3]
                                );
                        }
                        break;
                case 7:
                        atqa[0] |= 0x40;
                        sak_7[0] &= 0xFB;                                               
                        // save CUID
                        cuid = bytes_to_num(rUIDBCC2, 4);                       
                         // CascadeTag, CT
                        rUIDBCC1[0] = 0x88;
                        // BCC
                        rUIDBCC1[4] = rUIDBCC1[0] ^ rUIDBCC1[1] ^ rUIDBCC1[2] ^ rUIDBCC1[3]; 
                        rUIDBCC2[4] = rUIDBCC2[0] ^ rUIDBCC2[1] ^ rUIDBCC2[2] ^ rUIDBCC2[3]; 
                        if (MF_DBGLEVEL >= 2)   {
                                Dbprintf("7B UID: %02x %02x %02x %02x %02x %02x %02x",
                                        rUIDBCC1[1],
                                        rUIDBCC1[2],
                                        rUIDBCC1[3],
                                        rUIDBCC2[0],
                                        rUIDBCC2[1],
                                        rUIDBCC2[2],
                                        rUIDBCC2[3]
                                );
                        }
                        break;
                case 10:
                        atqa[0] |= 0x80;
                        sak_10[0] &= 0xFB;                                      
                        // save CUID
                        cuid = bytes_to_num(rUIDBCC3, 4);
                         // CascadeTag, CT
                        rUIDBCC1[0] = 0x88;
                        rUIDBCC2[0] = 0x88;
                        // BCC
                        rUIDBCC1[4] = rUIDBCC1[0] ^ rUIDBCC1[1] ^ rUIDBCC1[2] ^ rUIDBCC1[3];
                        rUIDBCC2[4] = rUIDBCC2[0] ^ rUIDBCC2[1] ^ rUIDBCC2[2] ^ rUIDBCC2[3];
                        rUIDBCC3[4] = rUIDBCC3[0] ^ rUIDBCC3[1] ^ rUIDBCC3[2] ^ rUIDBCC3[3];

                        if (MF_DBGLEVEL >= 2)   {
                                Dbprintf("10B UID: %02x %02x %02x %02x %02x %02x %02x %02x %02x %02x",
                                        rUIDBCC1[1],
                                        rUIDBCC1[2],
                                        rUIDBCC1[3],
                                        rUIDBCC2[1],
                                        rUIDBCC2[2],
                                        rUIDBCC2[3],
                                        rUIDBCC3[0],
                                        rUIDBCC3[1],
                                        rUIDBCC3[2],
                                        rUIDBCC3[3]
                                );
                        }
                        break;
                default: 
                        break;
        }
        // calc some crcs
        ComputeCrc14443(CRC_14443_A, sak_4, 1, &sak_4[1], &sak_4[2]);
        ComputeCrc14443(CRC_14443_A, sak_7, 1, &sak_7[1], &sak_7[2]);
        ComputeCrc14443(CRC_14443_A, sak_10, 1, &sak_10[1], &sak_10[2]);
        
        // We need to listen to the high-frequency, peak-detected path.
        iso14443a_setup(FPGA_HF_ISO14443A_TAGSIM_LISTEN);

        // free eventually allocated BigBuf memory but keep Emulator Memory
        BigBuf_free_keep_EM();
        clear_trace();
        set_tracing(TRUE);

        bool finished = FALSE;
        while (!BUTTON_PRESS() && !finished && !usb_poll_validate_length()) {
                WDT_HIT();

                // find reader field
                if (cardSTATE == MFEMUL_NOFIELD) {
                        vHf = (MAX_ADC_HF_VOLTAGE * AvgAdc(ADC_CHAN_HF)) >> 10;
                        if (vHf > MF_MINFIELDV) {
                                cardSTATE_TO_IDLE();
                                LED_A_ON();
                        }
                } 
                if (cardSTATE == MFEMUL_NOFIELD) continue;

                // Now, get data
                res = EmGetCmd(receivedCmd, &len, receivedCmd_par);
                if (res == 2) { //Field is off!
                        cardSTATE = MFEMUL_NOFIELD;
                        LEDsoff();
                        continue;
                } else if (res == 1) {
                        break;  // return value 1 means button press
                }
                        
                // REQ or WUP request in ANY state and WUP in HALTED state
                // this if-statement doesn't match the specification above. (iceman)
                if (len == 1 && ((receivedCmd[0] == ISO14443A_CMD_REQA && cardSTATE != MFEMUL_HALTED) || receivedCmd[0] == ISO14443A_CMD_WUPA)) {
                        selTimer = GetTickCount();
                        EmSendCmdEx(atqa, sizeof(atqa), (receivedCmd[0] == ISO14443A_CMD_WUPA));
                        cardSTATE = MFEMUL_SELECT1;
                        crypto1_destroy(pcs);
                        cardAUTHKEY = 0xff;
                        LEDsoff();
                        nonce = prand(); 
                        continue;
                }
                
                switch (cardSTATE) {
                        case MFEMUL_NOFIELD:
                        case MFEMUL_HALTED:
                        case MFEMUL_IDLE:{
                                LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                break;
                        }
                        case MFEMUL_SELECT1:{
                                if (len == 2 && (receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT && receivedCmd[1] == 0x20)) {
                                        if (MF_DBGLEVEL >= 4)   Dbprintf("SELECT ALL received");
                                        EmSendCmd(rUIDBCC1, sizeof(rUIDBCC1));
                                        break;
                                }
                                // select card
                                if (len == 9 && 
                                                ( receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT &&
                                                  receivedCmd[1] == 0x70 && 
                                                  memcmp(&receivedCmd[2], rUIDBCC1, 4) == 0)) {
                                        
                                        // SAK 4b 
                                        EmSendCmd(sak_4, sizeof(sak_4));
                                        switch(_UID_LEN){
                                                case 4:
                                                        cardSTATE = MFEMUL_WORK;
                                                        LED_B_ON();
                                                        if (MF_DBGLEVEL >= 4)   Dbprintf("--> WORK. anticol1 time: %d", GetTickCount() - selTimer);
                                                        continue;
                                                case 7:
                                                case 10:
                                                        cardSTATE = MFEMUL_SELECT2;
                                                        continue;
                                                default:break;
                                        }
                                } else {
                                        cardSTATE_TO_IDLE();
                                }
                                break;
                        }
                        case MFEMUL_SELECT2:{
                                if (!len) { 
                                        LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        break;
                                }
                                if (len == 2 && (receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT_2 && receivedCmd[1] == 0x20)) {
                                        EmSendCmd(rUIDBCC2, sizeof(rUIDBCC2));
                                        break;
                                }
                                if (len == 9 && 
                                                (receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT_2 &&
                                                 receivedCmd[1] == 0x70 && 
                                                 memcmp(&receivedCmd[2], rUIDBCC2, 4) == 0) ) {
                                                         
                                        EmSendCmd(sak_7, sizeof(sak_7));
                                        switch(_UID_LEN){
                                                case 7:
                                                        cardSTATE = MFEMUL_WORK;
                                                        LED_B_ON();
                                                        if (MF_DBGLEVEL >= 4)   Dbprintf("--> WORK. anticol2 time: %d", GetTickCount() - selTimer);
                                                        continue;
                                                case 10:
                                                        cardSTATE = MFEMUL_SELECT3;
                                                        continue;
                                                default:break;
                                        }
                                } 
                                cardSTATE_TO_IDLE();
                                break;
                        }
                        case MFEMUL_SELECT3:{
                                if (!len) { 
                                        LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        break;
                                }
                                if (len == 2 && (receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT_3 && receivedCmd[1] == 0x20)) {
                                        EmSendCmd(rUIDBCC3, sizeof(rUIDBCC3));
                                        break;
                                }
                                if (len == 9 && 
                                                (receivedCmd[0] == ISO14443A_CMD_ANTICOLL_OR_SELECT_3 &&
                                                 receivedCmd[1] == 0x70 && 
                                                 memcmp(&receivedCmd[2], rUIDBCC3, 4) == 0) ) {

                                        EmSendCmd(sak_10, sizeof(sak_10));
                                        cardSTATE = MFEMUL_WORK;
                                        LED_B_ON();
                                        if (MF_DBGLEVEL >= 4)   Dbprintf("--> WORK. anticol3 time: %d", GetTickCount() - selTimer);
                                        break;
                                }
                                cardSTATE_TO_IDLE();
                                break;
                        }
                        case MFEMUL_AUTH1:{
                                if( len != 8) {
                                        cardSTATE_TO_IDLE();
                                        LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        break;
                                }

                                uint32_t nr = bytes_to_num(receivedCmd, 4);
                                uint32_t ar = bytes_to_num(&receivedCmd[4], 4);

                                // Collect AR/NR per keytype & sector
                                if ( (flags & FLAG_NR_AR_ATTACK) == FLAG_NR_AR_ATTACK ) {
                                        
                                        int8_t index = -1;
                                        int8_t empty = -1;
                                        for (uint8_t i = 0; i < ATTACK_KEY_COUNT; i++) {
                                                // find which index to use
                                                if ( (cardAUTHSC == ar_nr_nonces[i].sector) &&  (cardAUTHKEY == ar_nr_nonces[i].keytype)) 
                                                        index = i;

                                                // keep track of empty slots.
                                                if ( ar_nr_nonces[i].state == EMPTY)
                                                        empty = i;
                                        }
                                        // if no empty slots.  Choose first and overwrite.
                                        if ( index == -1 ) {
                                                if ( empty == -1 ) {
                                                        index = 0;
                                                        ar_nr_nonces[index].state = EMPTY;
                                                } else {
                                                        index = empty;
                                                }
                                        }

                                        switch(ar_nr_nonces[index].state) {
                                                case EMPTY: {
                                                        // first nonce collect
                                                        ar_nr_nonces[index].cuid = cuid;
                                                        ar_nr_nonces[index].sector = cardAUTHSC;
                                                        ar_nr_nonces[index].keytype = cardAUTHKEY;
                                                        ar_nr_nonces[index].nonce = nonce;
                                                        ar_nr_nonces[index].nr = nr;
                                                        ar_nr_nonces[index].ar = ar;
                                                        ar_nr_nonces[index].state = FIRST;
                                                        break;
                                                } 
                                                case FIRST : { 
                                                        // second nonce collect
                                                        ar_nr_nonces[index].nonce2 = nonce;
                                                        ar_nr_nonces[index].nr2 = nr;
                                                        ar_nr_nonces[index].ar2 = ar;
                                                        ar_nr_nonces[index].state = SECOND;

                                                        // send to client
                                                        cmd_send(CMD_ACK, CMD_SIMULATE_MIFARE_CARD, 0, 0, &ar_nr_nonces[index], sizeof(nonces_t));
                                                        
                                                        ar_nr_nonces[index].state = EMPTY;
                                                        ar_nr_nonces[index].sector = 0;
                                                        ar_nr_nonces[index].keytype = 0;
                                                        break;
                                                }
                                                default: break;
                                        }
                                }

                                crypto1_word(pcs, nr , 1);
                                uint32_t cardRr = ar ^ crypto1_word(pcs, 0, 0);
                                
                                //test if auth OK
                                if (cardRr != prng_successor(nonce, 64)){
                                        
                                        if (MF_DBGLEVEL >= 3) {
                                                Dbprintf("AUTH FAILED for sector %d with key %c. [nr=%08x  cardRr=%08x] [nt=%08x succ=%08x]"
                                                        , cardAUTHSC
                                                        , (cardAUTHKEY == 0) ? 'A' : 'B'
                                                        , nr
                                                        , cardRr
                                                        , nonce // nt
                                                        , prng_successor(nonce, 64)
                                                );
                                        }
                                        // Shouldn't we respond anything here?
                                        // Right now, we don't nack or anything, which causes the
                                        // reader to do a WUPA after a while. /Martin
                                        // -- which is the correct response. /piwi
                                        cardSTATE_TO_IDLE();
                                        LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        break;
                                }
                                
                                ans = prng_successor(nonce, 96) ^ crypto1_word(pcs, 0, 0);
                                num_to_bytes(ans, 4, rAUTH_AT);
                                EmSendCmd(rAUTH_AT, sizeof(rAUTH_AT));
                                LED_C_ON();
                                
                                if (MF_DBGLEVEL >= 1) {
                                        Dbprintf("AUTH COMPLETED for sector %d with key %c. time=%d", 
                                                cardAUTHSC, 
                                                cardAUTHKEY == 0 ? 'A' : 'B',
                                                GetTickCount() - authTimer
                                        );
                                }
                                cardSTATE = MFEMUL_WORK;
                                break;
                        }
                        case MFEMUL_WORK:{
                                if (len == 0) {
                                        LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        break;
                                }               
                                bool encrypted_data = (cardAUTHKEY != 0xFF) ;

                                if(encrypted_data)
                                        mf_crypto1_decrypt(pcs, receivedCmd, len);
                                
                                if (len == 4 && (receivedCmd[0] == MIFARE_AUTH_KEYA || 
                                                 receivedCmd[0] == MIFARE_AUTH_KEYB)  ) {

                                        authTimer = GetTickCount();
                                        cardAUTHSC = receivedCmd[1] / 4;  // received block -> sector
                                        cardAUTHKEY = receivedCmd[0] & 0x1;
                                        crypto1_destroy(pcs);
                                        
                                        // load key into crypto
                                        crypto1_create(pcs, emlGetKey(cardAUTHSC, cardAUTHKEY));

                                        if (!encrypted_data) {
                                                // first authentication
                                                // Update crypto state init  (UID ^ NONCE)
                                                crypto1_word(pcs, cuid ^ nonce, 0);
                                                num_to_bytes(nonce, 4, rAUTH_AT);
                                        } else {
                                                // nested authentication
                                                ans = nonce ^ crypto1_word(pcs, cuid ^ nonce, 0); 
                                                num_to_bytes(ans, 4, rAUTH_AT);

                                                if (MF_DBGLEVEL >= 3) Dbprintf("Reader doing nested authentication for block %d (0x%02x) with key %c", receivedCmd[1], receivedCmd[1],  cardAUTHKEY == 0 ? 'A' : 'B');
                                        }

                                        EmSendCmd(rAUTH_AT, sizeof(rAUTH_AT));
                                        cardSTATE = MFEMUL_AUTH1;
                                        break;
                                }
                                
                                // rule 13 of 7.5.3. in ISO 14443-4. chaining shall be continued
                                // BUT... ACK --> NACK
                                if (len == 1 && receivedCmd[0] == CARD_ACK) {
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                        break;
                                }
                                
                                // rule 12 of 7.5.3. in ISO 14443-4. R(NAK) --> R(ACK)
                                if (len == 1 && receivedCmd[0] == CARD_NACK_NA) {
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_ACK));
                                        break;
                                }
                                
                                if(len != 4) {
                                        LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        break;
                                }

                                if ( receivedCmd[0] == ISO14443A_CMD_READBLOCK ||
                                         receivedCmd[0] == ISO14443A_CMD_WRITEBLOCK ||
                                         receivedCmd[0] == MIFARE_CMD_INC ||
                                         receivedCmd[0] == MIFARE_CMD_DEC ||
                                         receivedCmd[0] == MIFARE_CMD_RESTORE ||
                                         receivedCmd[0] == MIFARE_CMD_TRANSFER ) {
                                                
                                        if (receivedCmd[1] >= 16 * 4) {
                                                EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                                if (MF_DBGLEVEL >= 4) Dbprintf("Reader tried to operate (0x%02) on out of range block: %d (0x%02x), nacking",receivedCmd[0],receivedCmd[1],receivedCmd[1]);
                                                break;
                                        }

                                        if (receivedCmd[1] / 4 != cardAUTHSC) {
                                                EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                                if (MF_DBGLEVEL >= 4) Dbprintf("Reader tried to operate (0x%02) on block (0x%02x) not authenticated for (0x%02x), nacking",receivedCmd[0],receivedCmd[1],cardAUTHSC);
                                                break;
                                        }
                                }
                                // read block
                                if (receivedCmd[0] == ISO14443A_CMD_READBLOCK) {
                                        if (MF_DBGLEVEL >= 4) Dbprintf("Reader reading block %d (0x%02x)", receivedCmd[1], receivedCmd[1]);

                                        emlGetMem(response, receivedCmd[1], 1);
                                        AppendCrc14443a(response, 16);
                                        mf_crypto1_encrypt(pcs, response, 18, response_par);
                                        EmSendCmdPar(response, 18, response_par);
                                        numReads++;
                                        if(exitAfterNReads > 0 && numReads >= exitAfterNReads) {
                                                Dbprintf("%d reads done, exiting", numReads);
                                                finished = true;
                                        }
                                        break;
                                }
                                // write block
                                if (receivedCmd[0] == ISO14443A_CMD_WRITEBLOCK) {
                                        if (MF_DBGLEVEL >= 4) Dbprintf("RECV 0xA0 write block %d (%02x)", receivedCmd[1], receivedCmd[1]);
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_ACK));
                                        cardSTATE = MFEMUL_WRITEBL2;
                                        cardWRBL = receivedCmd[1];
                                        break;
                                }
                                // increment, decrement, restore
                                if ( receivedCmd[0] == MIFARE_CMD_INC || 
                                     receivedCmd[0] == MIFARE_CMD_DEC || 
                                         receivedCmd[0] == MIFARE_CMD_RESTORE) {

                                         if (MF_DBGLEVEL >= 4) Dbprintf("RECV 0x%02x inc(0xC1)/dec(0xC0)/restore(0xC2) block %d (%02x)",receivedCmd[0], receivedCmd[1], receivedCmd[1]);

                                        if (emlCheckValBl(receivedCmd[1])) {
                                                if (MF_DBGLEVEL >= 4) Dbprintf("Reader tried to operate on block, but emlCheckValBl failed, nacking");
                                                EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                                break;
                                        }
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_ACK));
                                        if (receivedCmd[0] == MIFARE_CMD_INC)           cardSTATE = MFEMUL_INTREG_INC;
                                        if (receivedCmd[0] == MIFARE_CMD_DEC)           cardSTATE = MFEMUL_INTREG_DEC;
                                        if (receivedCmd[0] == MIFARE_CMD_RESTORE)       cardSTATE = MFEMUL_INTREG_REST;
                                        cardWRBL = receivedCmd[1];
                                        break;
                                }
                                // transfer
                                if (receivedCmd[0] == MIFARE_CMD_TRANSFER) {
                                        if (MF_DBGLEVEL >= 4) Dbprintf("RECV 0x%02x transfer block %d (%02x)", receivedCmd[0], receivedCmd[1], receivedCmd[1]);
                                        if (emlSetValBl(cardINTREG, cardINTBLOCK, receivedCmd[1]))
                                                EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                        else
                                                EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_ACK));
                                        break;
                                }
                                // halt
                                if (receivedCmd[0] == ISO14443A_CMD_HALT && receivedCmd[1] == 0x00) {
                                        LED_B_OFF();
                                        LED_C_OFF();
                                        cardSTATE = MFEMUL_HALTED;
                                        if (MF_DBGLEVEL >= 4)   Dbprintf("--> HALTED. Selected time: %d ms",  GetTickCount() - selTimer);
                                        LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                        break;
                                }
                                // RATS
                                if (receivedCmd[0] == ISO14443A_CMD_RATS) {
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                        break;
                                }
                                // command not allowed
                                if (MF_DBGLEVEL >= 4)   Dbprintf("Received command not allowed, nacking");
                                EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                break;
                        }
                        case MFEMUL_WRITEBL2:{
                                if (len == 18) {
                                        mf_crypto1_decrypt(pcs, receivedCmd, len);
                                        emlSetMem(receivedCmd, cardWRBL, 1);
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_ACK));
                                        cardSTATE = MFEMUL_WORK;
                                } else {
                                        cardSTATE_TO_IDLE();
                                        LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                }
                                break;
                        }
                        case MFEMUL_INTREG_INC:{
                                mf_crypto1_decrypt(pcs, receivedCmd, len);
                                memcpy(&ans, receivedCmd, 4);
                                if (emlGetValBl(&cardINTREG, &cardINTBLOCK, cardWRBL)) {
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                        cardSTATE_TO_IDLE();
                                        break;
                                } 
                                LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                cardINTREG = cardINTREG + ans;
                                cardSTATE = MFEMUL_WORK;
                                break;
                        }
                        case MFEMUL_INTREG_DEC:{
                                mf_crypto1_decrypt(pcs, receivedCmd, len);
                                memcpy(&ans, receivedCmd, 4);
                                if (emlGetValBl(&cardINTREG, &cardINTBLOCK, cardWRBL)) {
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                        cardSTATE_TO_IDLE();
                                        break;
                                }
                                LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                cardINTREG = cardINTREG - ans;
                                cardSTATE = MFEMUL_WORK;
                                break;
                        }
                        case MFEMUL_INTREG_REST:{
                                mf_crypto1_decrypt(pcs, receivedCmd, len);
                                memcpy(&ans, receivedCmd, 4);
                                if (emlGetValBl(&cardINTREG, &cardINTBLOCK, cardWRBL)) {
                                        EmSend4bit(mf_crypto1_encrypt4bit(pcs, CARD_NACK_NA));
                                        cardSTATE_TO_IDLE();
                                        break;
                                }
                                LogTrace(Uart.output, Uart.len, Uart.startTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.endTime*16 - DELAY_AIR2ARM_AS_TAG, Uart.parity, TRUE);
                                cardSTATE = MFEMUL_WORK;
                                break;
                        }
                }
        }

        if (MF_DBGLEVEL >= 1) 
                Dbprintf("Emulator stopped. Tracing: %d  trace length: %d ", tracing, BigBuf_get_traceLen());
        
        cmd_send(CMD_ACK,1,0,0,0,0);    FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
        LEDsoff();
        set_tracing(FALSE);
}


//-----------------------------------------------------------------------------
// MIFARE sniffer. 
// 
// if no activity for 2sec, it sends the collected data to the client.
//-----------------------------------------------------------------------------
// "hf mf sniff"
void RAMFUNC SniffMifare(uint8_t param) {

        LEDsoff();

        // free eventually allocated BigBuf memory
        BigBuf_free(); BigBuf_Clear_ext(false);
        clear_trace();
        set_tracing(TRUE);

        // The command (reader -> tag) that we're receiving.
        uint8_t receivedCmd[MAX_MIFARE_FRAME_SIZE] = {0x00};    
        uint8_t receivedCmdPar[MAX_MIFARE_PARITY_SIZE] = {0x00};

        // The response (tag -> reader) that we're receiving.
        uint8_t receivedResponse[MAX_MIFARE_FRAME_SIZE] = {0x00};
        uint8_t receivedResponsePar[MAX_MIFARE_PARITY_SIZE] = {0x00};

        iso14443a_setup(FPGA_HF_ISO14443A_SNIFFER);

        // allocate the DMA buffer, used to stream samples from the FPGA
        // [iceman] is this sniffed data unsigned?
        uint8_t *dmaBuf = BigBuf_malloc(DMA_BUFFER_SIZE);
        uint8_t *data = dmaBuf;
        uint8_t previous_data = 0;
        int maxDataLen = 0;
        int dataLen = 0;
        bool ReaderIsActive = FALSE;
        bool TagIsActive = FALSE;

        // Set up the demodulator for tag -> reader responses.
        DemodInit(receivedResponse, receivedResponsePar);

        // Set up the demodulator for the reader -> tag commands
        UartInit(receivedCmd, receivedCmdPar);

        // Setup and start DMA.
        // set transfer address and number of bytes. Start transfer.
        if ( !FpgaSetupSscDma((uint8_t*) dmaBuf, DMA_BUFFER_SIZE) ){
                if (MF_DBGLEVEL > 1) Dbprintf("FpgaSetupSscDma failed. Exiting"); 
                return;
        }

        LED_D_OFF();

        MfSniffInit();

        // And now we loop, receiving samples.
        for(uint32_t sniffCounter = 0;; ) {

                LED_A_ON();
                WDT_HIT();
        
                if(BUTTON_PRESS()) {
                        DbpString("cancelled by button");
                        break;
                }
        
                if ((sniffCounter & 0x0000FFFF) == 0) { // from time to time
                        // check if a transaction is completed (timeout after 2000ms).
                        // if yes, stop the DMA transfer and send what we have so far to the client
                        if (MfSniffSend(2000)) {                        
                                // Reset everything - we missed some sniffed data anyway while the DMA was stopped
                                sniffCounter = 0;
                                data = dmaBuf;
                                maxDataLen = 0;
                                ReaderIsActive = FALSE;
                                TagIsActive = FALSE;
                                // Setup and start DMA. set transfer address and number of bytes. Start transfer.
                                if ( !FpgaSetupSscDma((uint8_t*) dmaBuf, DMA_BUFFER_SIZE) ){
                                        if (MF_DBGLEVEL > 1) Dbprintf("FpgaSetupSscDma failed. Exiting"); 
                                        return;
                                }                               
                        }
                }
                
                int register readBufDataP = data - dmaBuf;      // number of bytes we have processed so far
                int register dmaBufDataP = DMA_BUFFER_SIZE - AT91C_BASE_PDC_SSC->PDC_RCR; // number of bytes already transferred

                if (readBufDataP <= dmaBufDataP)                        // we are processing the same block of data which is currently being transferred
                        dataLen = dmaBufDataP - readBufDataP;   // number of bytes still to be processed
                else
                        dataLen = DMA_BUFFER_SIZE - readBufDataP + dmaBufDataP; // number of bytes still to be processed

                // test for length of buffer
                if(dataLen > maxDataLen) {                                      // we are more behind than ever...
                        maxDataLen = dataLen;                                   
                        if(dataLen > (9 * DMA_BUFFER_SIZE / 10)) {
                                Dbprintf("blew circular buffer! dataLen=0x%x", dataLen);
                                break;
                        }
                }
                if(dataLen < 1) continue;

                // primary buffer was stopped ( <-- we lost data!
                if (!AT91C_BASE_PDC_SSC->PDC_RCR) {
                        AT91C_BASE_PDC_SSC->PDC_RPR = (uint32_t) dmaBuf;
                        AT91C_BASE_PDC_SSC->PDC_RCR = DMA_BUFFER_SIZE;
                        Dbprintf("RxEmpty ERROR, data length:%d", dataLen); // temporary
                }
                // secondary buffer sets as primary, secondary buffer was stopped
                if (!AT91C_BASE_PDC_SSC->PDC_RNCR) {
                        AT91C_BASE_PDC_SSC->PDC_RNPR = (uint32_t) dmaBuf;
                        AT91C_BASE_PDC_SSC->PDC_RNCR = DMA_BUFFER_SIZE;
                }

                LED_A_OFF();
                
                if (sniffCounter & 0x01) {

                        // no need to try decoding tag data if the reader is sending
                        if(!TagIsActive) {              
                                uint8_t readerdata = (previous_data & 0xF0) | (*data >> 4);
                                if(MillerDecoding(readerdata, (sniffCounter-1)*4)) {
                                        LED_C_INV();

                                        if (MfSniffLogic(receivedCmd, Uart.len, Uart.parity, Uart.bitCount, TRUE)) break;

                                        UartInit(receivedCmd, receivedCmdPar);
                                        DemodReset();
                                }
                                ReaderIsActive = (Uart.state != STATE_UNSYNCD);
                        }
                        
                        // no need to try decoding tag data if the reader is sending
                        if(!ReaderIsActive) {           
                                uint8_t tagdata = (previous_data << 4) | (*data & 0x0F);
                                if(ManchesterDecoding(tagdata, 0, (sniffCounter-1)*4)) {
                                        LED_C_INV();

                                        if (MfSniffLogic(receivedResponse, Demod.len, Demod.parity, Demod.bitCount, FALSE)) break;

                                        DemodReset();
                                        UartInit(receivedCmd, receivedCmdPar);
                                }
                                TagIsActive = (Demod.state != DEMOD_UNSYNCD);
                        }
                }

                previous_data = *data;
                sniffCounter++;
                data++;

                if(data == dmaBuf + DMA_BUFFER_SIZE)
                        data = dmaBuf;

        } // main cycle
        
        if (MF_DBGLEVEL >= 1) Dbprintf("maxDataLen=%x, Uart.state=%x, Uart.len=%x", maxDataLen, Uart.state, Uart.len);
        
        FpgaDisableSscDma();
        MfSniffEnd();
        FpgaWriteConfWord(FPGA_MAJOR_MODE_OFF);
        LEDsoff();
        set_tracing(FALSE);
}