--- /dev/null
+/*
+ * board-mapphone-emu_uart.c
+ *
+ * Copyright (C) 2009 Motorola, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+/* Date Author Comment
+ * =========== ============== ==============================================
+ * Jun-26-2009 Motorola Initial revision.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+
+#include <linux/spi/spi.h>
+#include <plat/system.h>
+#include <linux/irq.h>
+
+#include <plat/dma.h>
+#include <plat/clock.h>
+#include <plat/board-mapphone-emu_uart.h>
+#include <plat/hardware.h>
+#include <plat/omap34xx.h>
+
+/*
+ * Register definitions for CPCAP related SPI register
+ */
+#define OMAP2_MCSPI_MAX_FREQ 48000000
+
+#define OMAP2_MCSPI_REVISION 0x00
+#define OMAP2_MCSPI_SYSCONFIG 0x10
+#define OMAP2_MCSPI_SYSSTATUS 0x14
+#define OMAP2_MCSPI_IRQSTATUS 0x18
+#define OMAP2_MCSPI_IRQENABLE 0x1c
+#define OMAP2_MCSPI_WAKEUPENABLE 0x20
+#define OMAP2_MCSPI_SYST 0x24
+#define OMAP2_MCSPI_MODULCTRL 0x28
+
+/* per-channel banks, 0x14 bytes each, first is: */
+#define OMAP2_MCSPI_CHCONF0 0x2c
+#define OMAP2_MCSPI_CHSTAT0 0x30
+#define OMAP2_MCSPI_CHCTRL0 0x34
+#define OMAP2_MCSPI_TX0 0x38
+#define OMAP2_MCSPI_RX0 0x3c
+
+/* per-register bitmasks: */
+
+#define OMAP2_MCSPI_SYSCONFIG_AUTOIDLE (1 << 0)
+#define OMAP2_MCSPI_SYSCONFIG_SOFTRESET (1 << 1)
+#define OMAP2_AFTR_RST_SET_MASTER (0 << 2)
+
+#define OMAP2_MCSPI_SYSSTATUS_RESETDONE (1 << 0)
+#define OMAP2_MCSPI_SYS_CON_LVL_1 1
+#define OMAP2_MCSPI_SYS_CON_LVL_2 2
+
+#define OMAP2_MCSPI_MODULCTRL_SINGLE (1 << 0)
+#define OMAP2_MCSPI_MODULCTRL_MS (1 << 2)
+#define OMAP2_MCSPI_MODULCTRL_STEST (1 << 3)
+
+#define OMAP2_MCSPI_CHCONF_PHA (1 << 0)
+#define OMAP2_MCSPI_CHCONF_POL (1 << 1)
+#define OMAP2_MCSPI_CHCONF_CLKD_MASK (0x0f << 2)
+#define OMAP2_MCSPI_CHCONF_EPOL (1 << 6)
+#define OMAP2_MCSPI_CHCONF_WL_MASK (0x1f << 7)
+#define OMAP2_MCSPI_CHCONF_TRM_RX_ONLY (0x01 << 12)
+#define OMAP2_MCSPI_CHCONF_TRM_TX_ONLY (0x02 << 12)
+#define OMAP2_MCSPI_CHCONF_TRM_MASK (0x03 << 12)
+#define OMAP2_MCSPI_CHCONF_TRM_TXRX (~OMAP2_MCSPI_CHCONF_TRM_MASK)
+#define OMAP2_MCSPI_CHCONF_DMAW (1 << 14)
+#define OMAP2_MCSPI_CHCONF_DMAR (1 << 15)
+#define OMAP2_MCSPI_CHCONF_DPE0 (1 << 16)
+#define OMAP2_MCSPI_CHCONF_DPE1 (1 << 17)
+#define OMAP2_MCSPI_CHCONF_IS (1 << 18)
+#define OMAP2_MCSPI_CHCONF_TURBO (1 << 19)
+#define OMAP2_MCSPI_CHCONF_FORCE (1 << 20)
+#define OMAP2_MCSPI_CHCONF_TCS0 (1 << 25)
+#define OMAP2_MCSPI_CHCONF_TCS1 (1 << 26)
+#define OMAP2_MCSPI_CHCONF_TCS_MASK (0x03 << 25)
+
+#define OMAP2_MCSPI_SYSCFG_WKUP (1 << 2)
+#define OMAP2_MCSPI_SYSCFG_IDL (2 << 3)
+#define OMAP2_MCSPI_SYSCFG_CLK (2 << 8)
+#define OMAP2_MCSPI_WAKEUP_EN (1 << 1)
+#define OMAP2_MCSPI_IRQ_WKS (1 << 16)
+#define OMAP2_MCSPI_CHSTAT_RXS (1 << 0)
+#define OMAP2_MCSPI_CHSTAT_TXS (1 << 1)
+#define OMAP2_MCSPI_CHSTAT_EOT (1 << 2)
+
+#define OMAP2_MCSPI_CHCTRL_EN (1 << 0)
+#define OMAP2_MCSPI_MODE_IS_MASTER 0
+#define OMAP2_MCSPI_MODE_IS_SLAVE 1
+#define OMAP_MCSPI_WAKEUP_ENABLE 1
+
+/*mcspi base address: (0x48098000)1st SPI, (0x4809A00) 2nd SPI*/
+#define OMAP_MCSPI_BASE 0x48098000
+
+#define WORD_LEN 32
+#define CLOCK_DIV 12 /* 2^(12)=4096 48000000/4096<19200 */
+
+#define LEVEL1 1
+#define LEVEL2 2
+#define WRITE_CPCAP 1
+#define READ_CPCAP 0
+
+#define CM_ICLKEN1_CORE 0x48004A10
+#define CM_FCLKEN1_CORE 0x48004A00
+#define OMAP2_MCSPI_EN_MCSPI1 (1 << 18)
+
+#define RESET_FAIL 1
+#define RAW_MOD_REG_BIT(val, mask, set) do { \
+ if (set) \
+ val |= mask; \
+ else \
+ val &= ~mask; \
+} while (0)
+
+struct cpcap_dev {
+ u16 address;
+ u16 value;
+ u32 result;
+ int access_flag;
+};
+
+static char tx[4];
+static bool emu_uart_is_active = FALSE;
+
+/* Although SPI driver is provided through linux system as implemented above,
+ * it can not cover some special situation.
+ *
+ * During Debug phase, OMAP may need to acess CPCAP by SPI
+ * to configure or check related register when boot up is not finished.
+ * However, at this time, spi driver integrated in linux system may not
+ * be initialized properly.
+ *
+ * So we provode the following SPI driver with common API for access capcap
+ * by SPI directly, i.e. we will skip the linux system driver,
+ * but access SPI hardware directly to configure read/write specially for
+ * cpcap access.
+ *
+ * So developer should be very careful to use these APIs:
+ *
+ * read_cpcap_register_raw()
+ * write_cpcap_register_raw()
+ *
+ * Pay attention: Only use them when boot up phase.
+ * Rasons are as follows:
+ * 1. Although we provide protection on these two APIs for concurrency and
+ * race conditions, it may impact the performance of system
+ * because it will mask all interrupts during access.
+ * 2. Calling these APIs will reset all SPI registers, and may make previous
+ * data lost during run time.
+ *
+ * So, if developer wants to access CPCAP after boot up is finished,
+ * we suggest they should use poweric interface.
+ *
+ */
+static inline void raw_writel_reg(u32 value, u32 reg)
+{
+ unsigned int absolute_reg = (u32)OMAP_MCSPI_BASE + reg;
+#if defined(LOCAL_DEVELOPER_DEBUG)
+ printk(KERN_ERR " raw write reg =0x%x value=0x%x \n", absolute_reg,
+ value);
+#endif
+ omap_writel(value, absolute_reg);
+}
+
+static inline u32 raw_readl_reg(u32 reg)
+{
+ u32 result;
+ unsigned int absolute_reg = (u32)OMAP_MCSPI_BASE + reg;
+ result = omap_readl(absolute_reg);
+#if defined(LOCAL_DEVELOPER_DEBUG)
+ printk(KERN_ERR " raw read reg =0x%x result =0x%x \n",
+ absolute_reg, result);
+#endif
+ return result;
+}
+
+static void raw_omap_mcspi_wakeup_enable(int level)
+{
+ u32 result;
+
+ /* configure SYSCONFIG register... */
+ if (level == LEVEL1) {
+ result = raw_readl_reg(OMAP2_MCSPI_SYSCONFIG);
+ result =
+ result | OMAP2_MCSPI_SYSCFG_WKUP |
+ OMAP2_MCSPI_SYSCFG_IDL | OMAP2_MCSPI_SYSCFG_CLK |
+ OMAP2_MCSPI_SYSCONFIG_AUTOIDLE;
+ raw_writel_reg(result, OMAP2_MCSPI_SYSCONFIG);
+ }
+
+ if (level == LEVEL2) {
+ result = raw_readl_reg(OMAP2_MCSPI_SYSCONFIG);
+ result =
+ result | OMAP2_MCSPI_SYSCFG_WKUP |
+ OMAP2_MCSPI_SYSCFG_IDL |
+ OMAP2_MCSPI_SYSCONFIG_AUTOIDLE;
+ RAW_MOD_REG_BIT(result, OMAP2_MCSPI_SYSCFG_CLK, 0);
+ raw_writel_reg(result, OMAP2_MCSPI_SYSCONFIG);
+ }
+
+ /* configure wakeupenable register... */
+ raw_writel_reg(OMAP2_MCSPI_WAKEUP_EN, OMAP2_MCSPI_WAKEUPENABLE);
+
+ /* configure enable interrupt register... */
+ result = raw_readl_reg(OMAP2_MCSPI_IRQENABLE);
+ result = result | OMAP2_MCSPI_IRQ_WKS;
+ raw_writel_reg(result, OMAP2_MCSPI_IRQENABLE);
+}
+
+static void raw_omap2_mcspi_set_master_mode(void)
+{
+ u32 result;
+
+ /* configure MCSPI_MODULCTRL register... */
+ result = raw_readl_reg(OMAP2_MCSPI_MODULCTRL);
+
+ RAW_MOD_REG_BIT(result, OMAP2_MCSPI_MODULCTRL_STEST, 0);
+ RAW_MOD_REG_BIT(result, OMAP2_MCSPI_MODULCTRL_MS,
+ OMAP2_MCSPI_MODE_IS_MASTER);
+ RAW_MOD_REG_BIT(result, OMAP2_MCSPI_MODULCTRL_SINGLE, 1);
+
+ raw_writel_reg(result, OMAP2_MCSPI_MODULCTRL);
+}
+
+static void raw_omap2_mcspi_channel_config(void)
+{
+ u32 result;
+
+ /* select channel 0... otherwise 0x14*channel_num */
+ result = raw_readl_reg(OMAP2_MCSPI_CHCONF0);
+
+ /* TCS Chip select Timing(2.5 clock cycles) */
+ result &= ~(OMAP2_MCSPI_CHCONF_TCS_MASK);
+ result |= OMAP2_MCSPI_CHCONF_TCS1;
+
+ /* configure master mode... */
+ result &= ~OMAP2_MCSPI_CHCONF_IS;
+ result &= ~OMAP2_MCSPI_CHCONF_DPE1;
+ result |= OMAP2_MCSPI_CHCONF_DPE0;
+
+ /* configure wordlength */
+ result &= ~OMAP2_MCSPI_CHCONF_WL_MASK;
+ result |= (WORD_LEN - 1) << 7;
+
+ /* configure active high */
+ result &= ~OMAP2_MCSPI_CHCONF_EPOL;
+
+ /* set clock divisor */
+ result &= ~OMAP2_MCSPI_CHCONF_CLKD_MASK;
+ result |= CLOCK_DIV << 2;
+
+ /* configure mode polarity=0 phase=0 */
+ result &= ~OMAP2_MCSPI_CHCONF_POL;
+ result &= ~OMAP2_MCSPI_CHCONF_PHA;
+
+ raw_writel_reg(result, OMAP2_MCSPI_CHCONF0);
+
+}
+
+static void raw_mcspi_setup(void)
+{
+ raw_omap_mcspi_wakeup_enable(LEVEL1);
+ raw_omap2_mcspi_set_master_mode();
+ raw_omap2_mcspi_channel_config();
+ raw_omap_mcspi_wakeup_enable(LEVEL2);
+}
+
+static int raw_mcspi_reset(void)
+{
+ unsigned long timeout;
+ u32 tmp;
+
+ raw_omap_mcspi_wakeup_enable(LEVEL1);
+
+ raw_writel_reg(OMAP2_MCSPI_SYSCONFIG_SOFTRESET,
+ OMAP2_MCSPI_SYSCONFIG);
+
+ timeout = jiffies + msecs_to_jiffies(1000);
+
+ do {
+ tmp = raw_readl_reg(OMAP2_MCSPI_SYSSTATUS);
+ if (time_after(jiffies, timeout)) {
+ printk(KERN_ERR "SPI Error: Reset is time out!\n");
+ return -RESET_FAIL;
+ }
+ } while (!(tmp & OMAP2_MCSPI_SYSSTATUS_RESETDONE));
+
+ /*configure all modules in reset master mode */
+ raw_writel_reg(OMAP2_AFTR_RST_SET_MASTER, OMAP2_MCSPI_MODULCTRL);
+
+ /* call wakeup function to set sysconfig as per pm activity */
+ raw_omap_mcspi_wakeup_enable(LEVEL1);
+ raw_omap_mcspi_wakeup_enable(LEVEL2);
+
+ return 0;
+}
+
+static void raw_omap2_mcspi_force_cs(int enable_tag)
+{
+ u32 result;
+ result = raw_readl_reg(OMAP2_MCSPI_CHCONF0);
+ /*
+ * Manual spim_csx assertion to keep spim_csx for channel x active
+ * RW 0x0 between SPI words (single channel master mode only).
+ */
+ RAW_MOD_REG_BIT(result, OMAP2_MCSPI_CHCONF_FORCE, enable_tag);
+ raw_writel_reg(result, OMAP2_MCSPI_CHCONF0);
+}
+
+static void raw_omap2_mcspi_set_enable(int enable)
+{
+ u32 result;
+
+ result = enable ? OMAP2_MCSPI_CHCTRL_EN : 0;
+ raw_writel_reg(result, OMAP2_MCSPI_CHCTRL0);
+}
+
+
+static int raw_mcspi_wait_for_reg_bit(unsigned long reg, unsigned long bit)
+{
+ unsigned long timeout;
+
+ timeout = jiffies + msecs_to_jiffies(1000);
+
+ while (!(raw_readl_reg(reg) & bit)) {
+ if (time_after(jiffies, timeout))
+ return -1;
+ }
+
+ return 0;
+}
+
+static void parser_cpcap(struct cpcap_dev *dev)
+{
+ if (dev->access_flag == WRITE_CPCAP) {
+ tx[3] = ((dev->address >> 6) & 0x000000FF) | 0x80;
+ tx[2] = (dev->address << 2) & 0x000000FF;
+ tx[1] = (dev->value >> 8) & 0x000000FF;
+ tx[0] = dev->value & 0x000000FF;
+ } else {
+ tx[3] = ((dev->address >> 6) & 0x000000FF);
+ tx[2] = (dev->address << 2) & 0x000000FF;
+ tx[1] = 1;
+ tx[0] = 1;
+ }
+}
+
+static void raw_omap2_mcspi_txrx_pio(struct cpcap_dev *dev)
+{
+ u32 result;
+ u32 tx_32bit;
+
+ /* config tranmission mode --- tx rx together */
+ result = raw_readl_reg(OMAP2_MCSPI_CHCONF0);
+ result &= ~OMAP2_MCSPI_CHCONF_TRM_MASK;
+ raw_writel_reg(result, OMAP2_MCSPI_CHCONF0);
+
+ /* enable the mcspi port! */
+ raw_omap2_mcspi_set_enable(1);
+
+ parser_cpcap(dev);
+
+ memcpy((void *)&tx_32bit, (void *)tx, 4);
+
+ if (raw_mcspi_wait_for_reg_bit(OMAP2_MCSPI_CHSTAT0,
+ OMAP2_MCSPI_CHSTAT_TXS) < 0) {
+ printk(KERN_ERR "SPI Error: TXS timed out\n");
+ goto out;
+ }
+ raw_writel_reg(tx_32bit, OMAP2_MCSPI_TX0);
+
+ if (raw_mcspi_wait_for_reg_bit(OMAP2_MCSPI_CHSTAT0,
+ OMAP2_MCSPI_CHSTAT_RXS) < 0) {
+ printk(KERN_ERR "SPI Error: RXS timed out\n");
+ goto out;
+ }
+
+ result = raw_readl_reg(OMAP2_MCSPI_RX0);
+
+ dev->result = result;
+
+out:
+ /* disable the mcspi port! */
+ raw_omap2_mcspi_set_enable(0);
+}
+
+static void raw_mcspi_run(struct cpcap_dev *dev)
+{
+ raw_omap_mcspi_wakeup_enable(LEVEL1);
+ raw_omap2_mcspi_set_master_mode();
+ raw_omap2_mcspi_channel_config();
+ raw_omap2_mcspi_force_cs(1);
+ raw_omap2_mcspi_txrx_pio(dev);
+ raw_omap2_mcspi_force_cs(0);
+ raw_omap_mcspi_wakeup_enable(LEVEL2);
+}
+
+static void raw_omap_mcspi_enable_IFclock(void)
+{
+ u32 result;
+
+ result = omap_readl(CM_FCLKEN1_CORE);
+ RAW_MOD_REG_BIT(result, OMAP2_MCSPI_EN_MCSPI1, 1);
+ omap_writel(result, CM_FCLKEN1_CORE);
+
+ result = omap_readl(CM_ICLKEN1_CORE);
+ RAW_MOD_REG_BIT(result, OMAP2_MCSPI_EN_MCSPI1, 1);
+ omap_writel(result, CM_ICLKEN1_CORE);
+
+}
+
+/*
+ * write_cpcap_register_raw is for cpcap spi write directly
+ * @return 0 on success; less than zero on failure.
+ */
+static int write_cpcap_register_raw(u16 addr, u16 val)
+{
+ int result;
+ unsigned long intr_flags;
+ struct cpcap_dev cpcap_write;
+
+#ifdef CONFIG_EMU_UART_DEBUG
+ if (is_emu_uart_active() && (addr == 897 || addr == 411))
+ return 0;
+#endif
+
+ local_irq_save(intr_flags);
+ raw_omap_mcspi_enable_IFclock();
+
+ result = raw_mcspi_reset();
+ if (result < 0) {
+ local_irq_restore(intr_flags);
+ printk(KERN_ERR "reset failed !\n");
+ return result;
+ }
+
+ raw_mcspi_setup();
+
+ cpcap_write.address = addr;
+ cpcap_write.value = val;
+ cpcap_write.access_flag = WRITE_CPCAP;
+ raw_mcspi_run(&cpcap_write);
+
+ local_irq_restore(intr_flags);
+
+ return result;
+}
+
+/*
+ * read_cpcap_register_raw is for cpcap spi read directly,
+ * read result is in val
+ * @return 0 on success; less than zero on failure.
+ */
+static int read_cpcap_register_raw(u16 addr, u16 *val)
+{
+ int result;
+ unsigned long intr_flag;
+ struct cpcap_dev cpcap_read;
+
+ local_irq_save(intr_flag);
+ raw_omap_mcspi_enable_IFclock();
+
+ result = raw_mcspi_reset();
+ if (result < 0) {
+ local_irq_restore(intr_flag);
+ printk(KERN_ERR "reset failed !\n");
+ return result;
+ }
+
+ raw_mcspi_setup();
+
+ cpcap_read.address = addr;
+ cpcap_read.access_flag = READ_CPCAP;
+ raw_mcspi_run(&cpcap_read);
+ *val = cpcap_read.result;
+
+ local_irq_restore(intr_flag);
+
+ return result;
+}
+
+/*
+ * Check if the writting is allowed. If MiniUSB port has already been
+ * configured as UART3, we should ignore some SCM register writting.
+ */
+int is_emu_uart_iomux_reg(unsigned short offset)
+{
+ if ((emu_uart_is_active) && \
+ ((offset >= 0x1A2 && offset < 0x1BA) || (offset == 0x19E)))
+ return 1;
+ else
+ return 0;
+}
+
+bool is_emu_uart_active(void)
+{
+ return emu_uart_is_active;
+}
+
+static void write_omap_mux_register(u16 offset, u8 mode, u8 input_en)
+{
+ u16 tmp_val, reg_val;
+ u32 reg = OMAP343X_CTRL_BASE + offset;
+
+ reg_val = mode | (input_en << 8);
+ tmp_val = omap_readw(reg) & ~(0x0007 | (1 << 8));
+ reg_val = reg_val | tmp_val;
+ omap_writew(reg_val, reg);
+}
+
+void activate_emu_uart(void)
+{
+ int i;
+ u16 tmp = 0;
+
+ read_cpcap_register_raw(18, &tmp);
+ printk(KERN_ALERT "Reading CPCAP vendor_version: 0x%04X\n", tmp);
+ /*
+ * Step 1:
+ * Configure OMAP SCM to set all ULPI pin of USB OTG to SAFE MODE
+ */
+ for (i = 0; i < 0x18; i += 2)
+ write_omap_mux_register(0x1A2 + i, 7, 0);
+
+ /*
+ * Step 2:
+ * Configure CPCAP to route UART3 to USB port; Switch VBUSIN to supply
+ * UART/USB transeiver and set VBUS standby mode 3
+ */
+ write_cpcap_register_raw(897, 0x0101);
+ write_cpcap_register_raw(411, 0x014C);
+
+ /* Step 3:
+ * Configure OMAP SCM to set ULPI port as UART3 function
+ */
+ /*
+ * Set UART3 RX pin in safe mode
+ */
+ write_omap_mux_register(0x19E, 7, 0);
+ /*
+ * Route UART3 TX to ULPIDATA0, RX to ULPIDATA1
+ */
+ write_omap_mux_register(0x1AA, 2, 0);
+ write_omap_mux_register(0x1AC, 2, 1);
+
+ emu_uart_is_active = TRUE;
+ printk
+ (KERN_ALERT "WARNING: MiniUSB port works in UART3 mode,"
+ "the USB functionality UNAVAILABLE!\n");
+
+}
projects / ms2-kexec / commitdiff