]> git.zerfleddert.de Git - usb-driver/blob - README
typo
[usb-driver] / README
1 This library emulates Jungo Windrvr USB and parallel port functions in
2 userspace which are required by XILINX impact to access the Platform cable USB
3 and Parallel Cable III.
4 With this library it is possible to access the cables without loading a
5 proprietary kernel module which breaks with every new kernel release. It uses
6 the functionality provided by the libusb userspace library for USB access and
7 the kernel interface at /dev/parport0 for parallel port access instead and
8 should work on every kernel version which is supported by libusb and supports
9 ppdev. It was written against impact from ISE Webpack 9.1SP1 and tested with
10 the following software:
11
12 * ISE Webpack 9.1SP3
13 * ISE Webpack 9.1SP2
14 * ISE Webpack 9.1SP1
15 * ISE Webpack 8.2SP3
16 * ISE Webpack 8.1SP3
17 * ChipScope 9.1.03i
18 * ChipScope 9.1.02i
19 * ChipScope 8.2.04i
20 * EDK 8.2.02i
21 * EDK 8.1.02i
22
23 In addition to the XILINX USB and parallel cables, devices based on the FTDI
24 2232 serial converter chip are also experimentally supported. This includes
25 devices like the Amontec JTAGkey(-Tiny).
26
27 Build the library by calling `make'.
28
29 To use this library you have to preload the library before starting impact:
30
31 $ LD_PRELOAD=/path/to/libusb-driver.so impact
32 or
33 $ export LD_PRELOAD=/path/to/libusb-driver.so (for sh shells)
34 $ setenv LD_PRELOAD /path/to/libusb-driver.so (for csh shells)
35 $ impact
36
37 The source for this library can be found at:
38 http://cvs.zerfleddert.de/cgi-bin/viewcvs.cgi/usb-driver/
39
40 The main website is located at:
41 http://www.rmdir.de/~michael/xilinx/
42
43
44 Notes for the USB cable
45 =======================
46
47 To use the device as an ordinary user, put the following line in a new
48 file in /etc/udev/rules.d/ and restart udev:
49 ACTION=="add", BUS=="usb", SYSFS{idVendor}=="03fd", MODE="666"
50
51
52 If your cable does not have the ID 03fd:0008 in the output of lsusb,
53 the initial firmware has not been loaded (loading it changes the
54 product-ID from another value to 8). To load the firmware follow
55 these steps:
56
57 1. If you have no /etc/udev/rules.d/xusbdfwu.rules file, copy it from
58 /path/to/ISE/bin/lin/xusbdfwu.rules to /etc/udev/rules.d/xusbdfwu.rules
59
60 2. Install the package containing /sbin/fxload from your linux distribution.
61 It is usually called "fxload"
62
63 3. copy the file /path/to/ISE/bin/lin/xusbdfwu.hex to /usr/share/xusbdfwu.hex
64
65 4. restart udev and re-plug the cable
66
67
68 Notes for the parallel cable
69 ============================
70
71 To access the parallel port from userspace, the kernel needs to be built with
72 the features "Parallel port support" (CONFIG_PARPORT), "PC-style hardware"
73 (CONFIG_PARPORT_PC) and "Support for user-space parallel port device drivers"
74 (CONFIG_PPDEV) builtin or as modules. If these features are built as modules,
75 they need to be loaded before using this library.
76 These modules are called:
77 parport
78 parport_pc
79 ppdev
80
81
82 To use the device as an ordinary user, put the user in the group 'lp'
83
84
85 If you have an almost compatible cable which works with other software but not
86 with Impact, try adding -DFORCE_PC3_IDENT to the CFLAGS line in the Makefile.
87 This enables a hack by Stefan Ziegenbalg to force detection of a parallel cable.
88
89
90 Parallel Cable IV is currently only supported in 'compatibility mode', as no
91 attempt to configure the ECP registers is done by this library.
92
93
94 If you get "Programming failed" or "DONE did not go high" when programming
95 through the parallel cable with Impact 9.1, make sure to have the option "Use
96 HIGHZ instead of BYPASS" enabled in Edit -> Preferences -> iMPACT Configuration
97 Preferences.
98 If you are using batch mode, add the following line to your cmd file:
99 setPreference -pref UseHighz:TRUE
100 (This problem also occurs on windows and when using the real windrvr in linux
101 and is solved with the same workaround. Impact 8.2 is working fine with the same
102 boards and designs)
103
104
105 Notes for FTDI 2232 based cables
106 ================================
107
108 To build the driver with FTDI 2232 support, you need to have libftdi and
109 the libftdi development package installed. On debian, you can install both
110 by installing 'libftdi-dev'.
111
112 To set-up the device:
113 1. Find out the vendor and product id of your cable using lsusb:
114 Bus 003 Device 005: ID 0403:cff8 Future Technology Devices ...
115 ~~~~~~~~~
116
117 2. Copy the sample libusb-driverrc to ~/.libusb-driverrc, edit it and replace
118 the vendor and product-id in the example file with the values provided in
119 the lsusb-output. You can also change the 'parallel port' which is mapped to
120 this cable. Impact sees the device at that port as a Parallel Cable III.
121
122 3. To use the device as an ordinary user, put the following line in a new file
123 in /etc/udev/rules.d/ and restart udev:
124 ACTION=="add", BUS=="usb", SYSFS{idVendor}=="0403", SYSFS{idProduct}=="cff8", MODE="666"
125 (replace the vendor and product id with your values)
126
127 The support for FTDI 2232 based devices is experimental and they are currently
128 significantly slower than the other supported cables.
Impressum, Datenschutz